u-boot/include/configs/zmx25.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

103 lines
2.1 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (c) 2011 Graf-Syteco, Matthias Weisser
* <weisserm@arcor.de>
*
* Configuation settings for the zmx25 board
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/imx-regs.h>
#define CONFIG_SYS_TIMER_RATE 32768
#define CONFIG_SYS_TIMER_COUNTER \
(&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
#define CONFIG_MACH_TYPE MACH_TYPE_ZMX25
/*
* Environment settings
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"gs_fast_boot=setenv bootdelay 5\0" \
"gs_slow_boot=setenv bootdelay 10\0" \
"bootcmd=dcache off; mw.l 0x81000000 0 1024; usb start;" \
"fatls usb 0; fatload usb 0 0x81000000 zmx25-init.bin;" \
"bootm 0x81000000; bootelf 0x81000000\0"
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/*
* Hardware drivers
*/
/*
* Serial
*/
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART2_BASE
/*
* Ethernet
*/
#define CONFIG_FEC_MXC
#define CONFIG_FEC_MXC_PHYADDR 0x00
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
/*
* Command line configuration.
*/
/*
* Additional command
*/
/*
* USB
*/
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI_MXC
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC MXC_EHCI_MODE_SERIAL
#define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
/* SDRAM */
#define PHYS_SDRAM 0x80000000 /* start address of LPDDRRAM */
#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_SP_ADDR 0x78020000 /* end of internal SRAM */
/*
* FLASH and environment organization
*/
#define CONFIG_SYS_FLASH_BASE 0xA0000000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 256
/*
* CFI FLASH driver setup
*/
#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM + (512*1024))
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM + PHYS_SDRAM_SIZE)
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (0x400000 - 0x8000)
#endif /* __CONFIG_H */