mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 19:10:13 +00:00
93e1459641
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Drop changes for PEP 4 following python tools] Signed-off-by: Tom Rini <trini@ti.com>
102 lines
4.2 KiB
Text
102 lines
4.2 KiB
Text
RAMBOOT for MPC85xx Platforms
|
|
==============================
|
|
|
|
RAMBOOT literally means boot from DDR. But since DDR is volatile memory some
|
|
pre-mechanism is required to load the DDR with the bootloader binary.
|
|
- In case of SD and SPI boot this is done by BootROM code inside the chip
|
|
itself.
|
|
- In case of NAND boot FCM supports loading initial 4K code from NAND flash
|
|
which can initialize the DDR and get the complete bootloader copied to DDR.
|
|
|
|
In addition to the above there could be some more methods to initialize the DDR
|
|
and load it manually.
|
|
Two of them are described below.There is also an explanation as to where these
|
|
methods could be handy.
|
|
1. Load the RAM based bootloader onto DDR via JTAG/BDI interface. And then
|
|
execute the bootloader from DDR.
|
|
This may be handy in the following cases:
|
|
- In very early stage of platform bringup where other boot options are not
|
|
functional because of various reasons.
|
|
- In case the support to program the flashes on the board is not available.
|
|
|
|
2. Load the RAM based bootloader onto DDR using already existing bootloader on
|
|
the board.And then execute the bootloader from DDR.
|
|
Some usecases where this may be used:
|
|
- While developing some new feature of u-boot, for example USB driver or
|
|
SPI driver.
|
|
Suppose the board already has a working bootloader on it. And you would
|
|
prefer to keep it intact, at the same time want to test your bootloader.
|
|
In this case you can get your test bootloader binary into DDR via tftp
|
|
for example. Then execute the test bootloader.
|
|
- Suppose a platform already has a propreitery bootloader which does not
|
|
support for example AMP boot. In this case also RAM boot loader can be
|
|
utilized.
|
|
|
|
So basically when the original bootloader is required to be kept intact
|
|
RAM based bootloader can offer an updated bootloader on the system.
|
|
|
|
Both the above Bootloaders are slight variants of SDcard or SPI Flash
|
|
bootloader or for that matter even NAND bootloader.
|
|
All of them define CONFIG_SYS_RAMBOOT.
|
|
The main difference among all of them is the way the pre-environment is getting
|
|
configured and who is doing that.
|
|
- In case of SD card and SPI flash bootloader this is done by On Chip BootROM inside the Si itself.
|
|
- In case of NAND boot SPL/TPL code does it with some support from Si itself.
|
|
- In case of the pure RAM based bootloaders we have to do it by JTAG manually or already existing bootloader.
|
|
|
|
How to use them:
|
|
1. Using JTAG
|
|
Boot up in core hold off mode or stop the core after reset using JTAG
|
|
interface.
|
|
Preconfigure DDR/L2SRAM through JTAG interface.
|
|
- setup DDR controller registers.
|
|
- setup DDR LAWs
|
|
- setup DDR TLB
|
|
Load the RAM based boot loader to the proper location in DDR/L2SRAM.
|
|
set up IAR (Instruction counter properly)
|
|
Enable the core to execute.
|
|
|
|
2. Using already existing bootloader.
|
|
get the rambased boot loader binary into DDR/L2SRAM via tftp.
|
|
execute the RAM based bootloader.
|
|
=> tftp 11000000 u-boot-ram.bin
|
|
=> go 1107f000
|
|
|
|
Please note that L2SRAM can also be used instead of DDR if the SOC has
|
|
sufficient size of L2SRAM.
|
|
|
|
Necessary Code changes Required:
|
|
=====================================
|
|
Please note that below mentioned changes are for 85xx platforms.
|
|
They have been tested on P1020/P2020/P1010 RDB.
|
|
|
|
The main difference between the above two methods from technical perspective is
|
|
that in 1st case SOC is just out of reset so it is in default configuration.
|
|
(CCSRBAR is at 0xff700000).
|
|
In the 2nd case bootloader has already re-located CCSRBAR to 0xffe00000
|
|
|
|
1. File name-> boards.cfg
|
|
There can be added specific Make options for RAMBoot. We can keep different
|
|
options for the two cases mentioned above.
|
|
for example
|
|
P1020RDB_JTAG_RAMBOOT and P1020RDB_GO_RAMBOOT.
|
|
|
|
2. platform config file
|
|
for example include/configs/P1_P2_RDB.h
|
|
|
|
#ifdef CONFIG_RAMBOOT
|
|
#define CONFIG_SDCARD
|
|
#endif
|
|
|
|
This will finally use the CONFIG_SYS_RAMBOOT.
|
|
|
|
3. File name-> arch/powerpc/include/asm/config_mpc85xx.h
|
|
In the section of the particular SOC, for example P1020,
|
|
|
|
#if defined(CONFIG_GO)
|
|
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xffe00000
|
|
#else
|
|
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
|
|
#endif
|
|
|
|
For JTAG RAMBOOT this is not required because CCSRBAR is at ff700000.
|