mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 00:47:26 +00:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
1561 lines
47 KiB
C
1561 lines
47 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2014 Gateworks Corporation
|
|
* Author: Tim Harvey <tharvey@gateworks.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <linux/types.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/mx6-ddr.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/io.h>
|
|
#include <asm/types.h>
|
|
#include <wait_bit.h>
|
|
|
|
#if defined(CONFIG_MX6_DDRCAL)
|
|
static void reset_read_data_fifos(void)
|
|
{
|
|
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
|
|
/* Reset data FIFOs twice. */
|
|
setbits_le32(&mmdc0->mpdgctrl0, 1 << 31);
|
|
wait_for_bit_le32(&mmdc0->mpdgctrl0, 1 << 31, 0, 100, 0);
|
|
|
|
setbits_le32(&mmdc0->mpdgctrl0, 1 << 31);
|
|
wait_for_bit_le32(&mmdc0->mpdgctrl0, 1 << 31, 0, 100, 0);
|
|
}
|
|
|
|
static void precharge_all(const bool cs0_enable, const bool cs1_enable)
|
|
{
|
|
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
|
|
/*
|
|
* Issue the Precharge-All command to the DDR device for both
|
|
* chip selects. Note, CON_REQ bit should also remain set. If
|
|
* only using one chip select, then precharge only the desired
|
|
* chip select.
|
|
*/
|
|
if (cs0_enable) { /* CS0 */
|
|
writel(0x04008050, &mmdc0->mdscr);
|
|
wait_for_bit_le32(&mmdc0->mdscr, 1 << 14, 1, 100, 0);
|
|
}
|
|
|
|
if (cs1_enable) { /* CS1 */
|
|
writel(0x04008058, &mmdc0->mdscr);
|
|
wait_for_bit_le32(&mmdc0->mdscr, 1 << 14, 1, 100, 0);
|
|
}
|
|
}
|
|
|
|
static void force_delay_measurement(int bus_size)
|
|
{
|
|
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
|
|
|
writel(0x800, &mmdc0->mpmur0);
|
|
if (bus_size == 0x2)
|
|
writel(0x800, &mmdc1->mpmur0);
|
|
}
|
|
|
|
static void modify_dg_result(u32 *reg_st0, u32 *reg_st1, u32 *reg_ctrl)
|
|
{
|
|
u32 dg_tmp_val, dg_dl_abs_offset, dg_hc_del, val_ctrl;
|
|
|
|
/*
|
|
* DQS gating absolute offset should be modified from reflecting
|
|
* (HW_DG_LOWx + HW_DG_UPx)/2 to reflecting (HW_DG_UPx - 0x80)
|
|
*/
|
|
|
|
val_ctrl = readl(reg_ctrl);
|
|
val_ctrl &= 0xf0000000;
|
|
|
|
dg_tmp_val = ((readl(reg_st0) & 0x07ff0000) >> 16) - 0xc0;
|
|
dg_dl_abs_offset = dg_tmp_val & 0x7f;
|
|
dg_hc_del = (dg_tmp_val & 0x780) << 1;
|
|
|
|
val_ctrl |= dg_dl_abs_offset + dg_hc_del;
|
|
|
|
dg_tmp_val = ((readl(reg_st1) & 0x07ff0000) >> 16) - 0xc0;
|
|
dg_dl_abs_offset = dg_tmp_val & 0x7f;
|
|
dg_hc_del = (dg_tmp_val & 0x780) << 1;
|
|
|
|
val_ctrl |= (dg_dl_abs_offset + dg_hc_del) << 16;
|
|
|
|
writel(val_ctrl, reg_ctrl);
|
|
}
|
|
|
|
static void correct_mpwldectr_result(void *reg)
|
|
{
|
|
/* Limit is 200/256 of CK, which is WL_HC_DELx | 0x48. */
|
|
const unsigned int limit = 0x148;
|
|
u32 val = readl(reg);
|
|
u32 old = val;
|
|
|
|
if ((val & 0x17f) > limit)
|
|
val &= 0xffff << 16;
|
|
|
|
if (((val >> 16) & 0x17f) > limit)
|
|
val &= 0xffff;
|
|
|
|
if (old != val)
|
|
writel(val, reg);
|
|
}
|
|
|
|
int mmdc_do_write_level_calibration(struct mx6_ddr_sysinfo const *sysinfo)
|
|
{
|
|
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
|
u32 esdmisc_val, zq_val;
|
|
u32 errors = 0;
|
|
u32 ldectrl[4] = {0};
|
|
u32 ddr_mr1 = 0x4;
|
|
u32 rwalat_max;
|
|
|
|
/*
|
|
* Stash old values in case calibration fails,
|
|
* we need to restore them
|
|
*/
|
|
ldectrl[0] = readl(&mmdc0->mpwldectrl0);
|
|
ldectrl[1] = readl(&mmdc0->mpwldectrl1);
|
|
if (sysinfo->dsize == 2) {
|
|
ldectrl[2] = readl(&mmdc1->mpwldectrl0);
|
|
ldectrl[3] = readl(&mmdc1->mpwldectrl1);
|
|
}
|
|
|
|
/* disable DDR logic power down timer */
|
|
clrbits_le32(&mmdc0->mdpdc, 0xff00);
|
|
|
|
/* disable Adopt power down timer */
|
|
setbits_le32(&mmdc0->mapsr, 0x1);
|
|
|
|
debug("Starting write leveling calibration.\n");
|
|
|
|
/*
|
|
* 2. disable auto refresh and ZQ calibration
|
|
* before proceeding with Write Leveling calibration
|
|
*/
|
|
esdmisc_val = readl(&mmdc0->mdref);
|
|
writel(0x0000C000, &mmdc0->mdref);
|
|
zq_val = readl(&mmdc0->mpzqhwctrl);
|
|
writel(zq_val & ~0x3, &mmdc0->mpzqhwctrl);
|
|
|
|
/* 3. increase walat and ralat to maximum */
|
|
rwalat_max = (1 << 6) | (1 << 7) | (1 << 8) | (1 << 16) | (1 << 17);
|
|
setbits_le32(&mmdc0->mdmisc, rwalat_max);
|
|
if (sysinfo->dsize == 2)
|
|
setbits_le32(&mmdc1->mdmisc, rwalat_max);
|
|
/*
|
|
* 4 & 5. Configure the external DDR device to enter write-leveling
|
|
* mode through Load Mode Register command.
|
|
* Register setting:
|
|
* Bits[31:16] MR1 value (0x0080 write leveling enable)
|
|
* Bit[9] set WL_EN to enable MMDC DQS output
|
|
* Bits[6:4] set CMD bits for Load Mode Register programming
|
|
* Bits[2:0] set CMD_BA to 0x1 for DDR MR1 programming
|
|
*/
|
|
writel(0x00808231, &mmdc0->mdscr);
|
|
|
|
/* 6. Activate automatic calibration by setting MPWLGCR[HW_WL_EN] */
|
|
writel(0x00000001, &mmdc0->mpwlgcr);
|
|
|
|
/*
|
|
* 7. Upon completion of this process the MMDC de-asserts
|
|
* the MPWLGCR[HW_WL_EN]
|
|
*/
|
|
wait_for_bit_le32(&mmdc0->mpwlgcr, 1 << 0, 0, 100, 0);
|
|
|
|
/*
|
|
* 8. check for any errors: check both PHYs for x64 configuration,
|
|
* if x32, check only PHY0
|
|
*/
|
|
if (readl(&mmdc0->mpwlgcr) & 0x00000F00)
|
|
errors |= 1;
|
|
if (sysinfo->dsize == 2)
|
|
if (readl(&mmdc1->mpwlgcr) & 0x00000F00)
|
|
errors |= 2;
|
|
|
|
debug("Ending write leveling calibration. Error mask: 0x%x\n", errors);
|
|
|
|
/* check to see if cal failed */
|
|
if ((readl(&mmdc0->mpwldectrl0) == 0x001F001F) &&
|
|
(readl(&mmdc0->mpwldectrl1) == 0x001F001F) &&
|
|
((sysinfo->dsize < 2) ||
|
|
((readl(&mmdc1->mpwldectrl0) == 0x001F001F) &&
|
|
(readl(&mmdc1->mpwldectrl1) == 0x001F001F)))) {
|
|
debug("Cal seems to have soft-failed due to memory not supporting write leveling on all channels. Restoring original write leveling values.\n");
|
|
writel(ldectrl[0], &mmdc0->mpwldectrl0);
|
|
writel(ldectrl[1], &mmdc0->mpwldectrl1);
|
|
if (sysinfo->dsize == 2) {
|
|
writel(ldectrl[2], &mmdc1->mpwldectrl0);
|
|
writel(ldectrl[3], &mmdc1->mpwldectrl1);
|
|
}
|
|
errors |= 4;
|
|
}
|
|
|
|
correct_mpwldectr_result(&mmdc0->mpwldectrl0);
|
|
correct_mpwldectr_result(&mmdc0->mpwldectrl1);
|
|
if (sysinfo->dsize == 2) {
|
|
correct_mpwldectr_result(&mmdc1->mpwldectrl0);
|
|
correct_mpwldectr_result(&mmdc1->mpwldectrl1);
|
|
}
|
|
|
|
/*
|
|
* User should issue MRS command to exit write leveling mode
|
|
* through Load Mode Register command
|
|
* Register setting:
|
|
* Bits[31:16] MR1 value "ddr_mr1" value from initialization
|
|
* Bit[9] clear WL_EN to disable MMDC DQS output
|
|
* Bits[6:4] set CMD bits for Load Mode Register programming
|
|
* Bits[2:0] set CMD_BA to 0x1 for DDR MR1 programming
|
|
*/
|
|
writel((ddr_mr1 << 16) + 0x8031, &mmdc0->mdscr);
|
|
|
|
/* re-enable auto refresh and zq cal */
|
|
writel(esdmisc_val, &mmdc0->mdref);
|
|
writel(zq_val, &mmdc0->mpzqhwctrl);
|
|
|
|
debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n",
|
|
readl(&mmdc0->mpwldectrl0));
|
|
debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n",
|
|
readl(&mmdc0->mpwldectrl1));
|
|
if (sysinfo->dsize == 2) {
|
|
debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n",
|
|
readl(&mmdc1->mpwldectrl0));
|
|
debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n",
|
|
readl(&mmdc1->mpwldectrl1));
|
|
}
|
|
|
|
/* We must force a readback of these values, to get them to stick */
|
|
readl(&mmdc0->mpwldectrl0);
|
|
readl(&mmdc0->mpwldectrl1);
|
|
if (sysinfo->dsize == 2) {
|
|
readl(&mmdc1->mpwldectrl0);
|
|
readl(&mmdc1->mpwldectrl1);
|
|
}
|
|
|
|
/* enable DDR logic power down timer: */
|
|
setbits_le32(&mmdc0->mdpdc, 0x00005500);
|
|
|
|
/* Enable Adopt power down timer: */
|
|
clrbits_le32(&mmdc0->mapsr, 0x1);
|
|
|
|
/* Clear CON_REQ */
|
|
writel(0, &mmdc0->mdscr);
|
|
|
|
return errors;
|
|
}
|
|
|
|
int mmdc_do_dqs_calibration(struct mx6_ddr_sysinfo const *sysinfo)
|
|
{
|
|
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
|
struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux =
|
|
(struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE;
|
|
bool cs0_enable;
|
|
bool cs1_enable;
|
|
bool cs0_enable_initial;
|
|
bool cs1_enable_initial;
|
|
u32 esdmisc_val;
|
|
u32 temp_ref;
|
|
u32 pddword = 0x00ffff00; /* best so far, place into MPPDCMPR1 */
|
|
u32 errors = 0;
|
|
u32 initdelay = 0x40404040;
|
|
|
|
/* check to see which chip selects are enabled */
|
|
cs0_enable_initial = readl(&mmdc0->mdctl) & 0x80000000;
|
|
cs1_enable_initial = readl(&mmdc0->mdctl) & 0x40000000;
|
|
|
|
/* disable DDR logic power down timer: */
|
|
clrbits_le32(&mmdc0->mdpdc, 0xff00);
|
|
|
|
/* disable Adopt power down timer: */
|
|
setbits_le32(&mmdc0->mapsr, 0x1);
|
|
|
|
/* set DQS pull ups */
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000);
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000);
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000);
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000);
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000);
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000);
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000);
|
|
setbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000);
|
|
|
|
/* Save old RALAT and WALAT values */
|
|
esdmisc_val = readl(&mmdc0->mdmisc);
|
|
|
|
setbits_le32(&mmdc0->mdmisc,
|
|
(1 << 6) | (1 << 7) | (1 << 8) | (1 << 16) | (1 << 17));
|
|
|
|
/* Disable auto refresh before proceeding with calibration */
|
|
temp_ref = readl(&mmdc0->mdref);
|
|
writel(0x0000c000, &mmdc0->mdref);
|
|
|
|
/*
|
|
* Per the ref manual, issue one refresh cycle MDSCR[CMD]= 0x2,
|
|
* this also sets the CON_REQ bit.
|
|
*/
|
|
if (cs0_enable_initial)
|
|
writel(0x00008020, &mmdc0->mdscr);
|
|
if (cs1_enable_initial)
|
|
writel(0x00008028, &mmdc0->mdscr);
|
|
|
|
/* poll to make sure the con_ack bit was asserted */
|
|
wait_for_bit_le32(&mmdc0->mdscr, 1 << 14, 1, 100, 0);
|
|
|
|
/*
|
|
* Check MDMISC register CALIB_PER_CS to see which CS calibration
|
|
* is targeted to (under normal cases, it should be cleared
|
|
* as this is the default value, indicating calibration is directed
|
|
* to CS0).
|
|
* Disable the other chip select not being target for calibration
|
|
* to avoid any potential issues. This will get re-enabled at end
|
|
* of calibration.
|
|
*/
|
|
if ((readl(&mmdc0->mdmisc) & 0x00100000) == 0)
|
|
clrbits_le32(&mmdc0->mdctl, 1 << 30); /* clear SDE_1 */
|
|
else
|
|
clrbits_le32(&mmdc0->mdctl, 1 << 31); /* clear SDE_0 */
|
|
|
|
/*
|
|
* Check to see which chip selects are now enabled for
|
|
* the remainder of the calibration.
|
|
*/
|
|
cs0_enable = readl(&mmdc0->mdctl) & 0x80000000;
|
|
cs1_enable = readl(&mmdc0->mdctl) & 0x40000000;
|
|
|
|
precharge_all(cs0_enable, cs1_enable);
|
|
|
|
/* Write the pre-defined value into MPPDCMPR1 */
|
|
writel(pddword, &mmdc0->mppdcmpr1);
|
|
|
|
/*
|
|
* Issue a write access to the external DDR device by setting
|
|
* the bit SW_DUMMY_WR (bit 0) in the MPSWDAR0 and then poll
|
|
* this bit until it clears to indicate completion of the write access.
|
|
*/
|
|
setbits_le32(&mmdc0->mpswdar0, 1);
|
|
wait_for_bit_le32(&mmdc0->mpswdar0, 1 << 0, 0, 100, 0);
|
|
|
|
/* Set the RD_DL_ABS# bits to their default values
|
|
* (will be calibrated later in the read delay-line calibration).
|
|
* Both PHYs for x64 configuration, if x32, do only PHY0.
|
|
*/
|
|
writel(initdelay, &mmdc0->mprddlctl);
|
|
if (sysinfo->dsize == 0x2)
|
|
writel(initdelay, &mmdc1->mprddlctl);
|
|
|
|
/* Force a measurment, for previous delay setup to take effect. */
|
|
force_delay_measurement(sysinfo->dsize);
|
|
|
|
/*
|
|
* ***************************
|
|
* Read DQS Gating calibration
|
|
* ***************************
|
|
*/
|
|
debug("Starting Read DQS Gating calibration.\n");
|
|
|
|
/*
|
|
* Reset the read data FIFOs (two resets); only need to issue reset
|
|
* to PHY0 since in x64 mode, the reset will also go to PHY1.
|
|
*/
|
|
reset_read_data_fifos();
|
|
|
|
/*
|
|
* Start the automatic read DQS gating calibration process by
|
|
* asserting MPDGCTRL0[HW_DG_EN] and MPDGCTRL0[DG_CMP_CYC]
|
|
* and then poll MPDGCTRL0[HW_DG_EN]] until this bit clears
|
|
* to indicate completion.
|
|
* Also, ensure that MPDGCTRL0[HW_DG_ERR] is clear to indicate
|
|
* no errors were seen during calibration.
|
|
*/
|
|
|
|
/*
|
|
* Set bit 30: chooses option to wait 32 cycles instead of
|
|
* 16 before comparing read data.
|
|
*/
|
|
setbits_le32(&mmdc0->mpdgctrl0, 1 << 30);
|
|
if (sysinfo->dsize == 2)
|
|
setbits_le32(&mmdc1->mpdgctrl0, 1 << 30);
|
|
|
|
/* Set bit 28 to start automatic read DQS gating calibration */
|
|
setbits_le32(&mmdc0->mpdgctrl0, 5 << 28);
|
|
|
|
/* Poll for completion. MPDGCTRL0[HW_DG_EN] should be 0 */
|
|
wait_for_bit_le32(&mmdc0->mpdgctrl0, 1 << 28, 0, 100, 0);
|
|
|
|
/*
|
|
* Check to see if any errors were encountered during calibration
|
|
* (check MPDGCTRL0[HW_DG_ERR]).
|
|
* Check both PHYs for x64 configuration, if x32, check only PHY0.
|
|
*/
|
|
if (readl(&mmdc0->mpdgctrl0) & 0x00001000)
|
|
errors |= 1;
|
|
|
|
if ((sysinfo->dsize == 0x2) && (readl(&mmdc1->mpdgctrl0) & 0x00001000))
|
|
errors |= 2;
|
|
|
|
/* now disable mpdgctrl0[DG_CMP_CYC] */
|
|
clrbits_le32(&mmdc0->mpdgctrl0, 1 << 30);
|
|
if (sysinfo->dsize == 2)
|
|
clrbits_le32(&mmdc1->mpdgctrl0, 1 << 30);
|
|
|
|
/*
|
|
* DQS gating absolute offset should be modified from
|
|
* reflecting (HW_DG_LOWx + HW_DG_UPx)/2 to
|
|
* reflecting (HW_DG_UPx - 0x80)
|
|
*/
|
|
modify_dg_result(&mmdc0->mpdghwst0, &mmdc0->mpdghwst1,
|
|
&mmdc0->mpdgctrl0);
|
|
modify_dg_result(&mmdc0->mpdghwst2, &mmdc0->mpdghwst3,
|
|
&mmdc0->mpdgctrl1);
|
|
if (sysinfo->dsize == 0x2) {
|
|
modify_dg_result(&mmdc1->mpdghwst0, &mmdc1->mpdghwst1,
|
|
&mmdc1->mpdgctrl0);
|
|
modify_dg_result(&mmdc1->mpdghwst2, &mmdc1->mpdghwst3,
|
|
&mmdc1->mpdgctrl1);
|
|
}
|
|
debug("Ending Read DQS Gating calibration. Error mask: 0x%x\n", errors);
|
|
|
|
/*
|
|
* **********************
|
|
* Read Delay calibration
|
|
* **********************
|
|
*/
|
|
debug("Starting Read Delay calibration.\n");
|
|
|
|
reset_read_data_fifos();
|
|
|
|
/*
|
|
* 4. Issue the Precharge-All command to the DDR device for both
|
|
* chip selects. If only using one chip select, then precharge
|
|
* only the desired chip select.
|
|
*/
|
|
precharge_all(cs0_enable, cs1_enable);
|
|
|
|
/*
|
|
* 9. Read delay-line calibration
|
|
* Start the automatic read calibration process by asserting
|
|
* MPRDDLHWCTL[HW_RD_DL_EN].
|
|
*/
|
|
writel(0x00000030, &mmdc0->mprddlhwctl);
|
|
|
|
/*
|
|
* 10. poll for completion
|
|
* MMDC indicates that the write data calibration had finished by
|
|
* setting MPRDDLHWCTL[HW_RD_DL_EN] = 0. Also, ensure that
|
|
* no error bits were set.
|
|
*/
|
|
wait_for_bit_le32(&mmdc0->mprddlhwctl, 1 << 4, 0, 100, 0);
|
|
|
|
/* check both PHYs for x64 configuration, if x32, check only PHY0 */
|
|
if (readl(&mmdc0->mprddlhwctl) & 0x0000000f)
|
|
errors |= 4;
|
|
|
|
if ((sysinfo->dsize == 0x2) &&
|
|
(readl(&mmdc1->mprddlhwctl) & 0x0000000f))
|
|
errors |= 8;
|
|
|
|
debug("Ending Read Delay calibration. Error mask: 0x%x\n", errors);
|
|
|
|
/*
|
|
* ***********************
|
|
* Write Delay Calibration
|
|
* ***********************
|
|
*/
|
|
debug("Starting Write Delay calibration.\n");
|
|
|
|
reset_read_data_fifos();
|
|
|
|
/*
|
|
* 4. Issue the Precharge-All command to the DDR device for both
|
|
* chip selects. If only using one chip select, then precharge
|
|
* only the desired chip select.
|
|
*/
|
|
precharge_all(cs0_enable, cs1_enable);
|
|
|
|
/*
|
|
* 8. Set the WR_DL_ABS# bits to their default values.
|
|
* Both PHYs for x64 configuration, if x32, do only PHY0.
|
|
*/
|
|
writel(initdelay, &mmdc0->mpwrdlctl);
|
|
if (sysinfo->dsize == 0x2)
|
|
writel(initdelay, &mmdc1->mpwrdlctl);
|
|
|
|
/*
|
|
* XXX This isn't in the manual. Force a measurement,
|
|
* for previous delay setup to effect.
|
|
*/
|
|
force_delay_measurement(sysinfo->dsize);
|
|
|
|
/*
|
|
* 9. 10. Start the automatic write calibration process
|
|
* by asserting MPWRDLHWCTL0[HW_WR_DL_EN].
|
|
*/
|
|
writel(0x00000030, &mmdc0->mpwrdlhwctl);
|
|
|
|
/*
|
|
* Poll for completion.
|
|
* MMDC indicates that the write data calibration had finished
|
|
* by setting MPWRDLHWCTL[HW_WR_DL_EN] = 0.
|
|
* Also, ensure that no error bits were set.
|
|
*/
|
|
wait_for_bit_le32(&mmdc0->mpwrdlhwctl, 1 << 4, 0, 100, 0);
|
|
|
|
/* Check both PHYs for x64 configuration, if x32, check only PHY0 */
|
|
if (readl(&mmdc0->mpwrdlhwctl) & 0x0000000f)
|
|
errors |= 16;
|
|
|
|
if ((sysinfo->dsize == 0x2) &&
|
|
(readl(&mmdc1->mpwrdlhwctl) & 0x0000000f))
|
|
errors |= 32;
|
|
|
|
debug("Ending Write Delay calibration. Error mask: 0x%x\n", errors);
|
|
|
|
reset_read_data_fifos();
|
|
|
|
/* Enable DDR logic power down timer */
|
|
setbits_le32(&mmdc0->mdpdc, 0x00005500);
|
|
|
|
/* Enable Adopt power down timer */
|
|
clrbits_le32(&mmdc0->mapsr, 0x1);
|
|
|
|
/* Restore MDMISC value (RALAT, WALAT) to MMDCP1 */
|
|
writel(esdmisc_val, &mmdc0->mdmisc);
|
|
|
|
/* Clear DQS pull ups */
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000);
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000);
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000);
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000);
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000);
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000);
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000);
|
|
clrbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000);
|
|
|
|
/* Re-enable SDE (chip selects) if they were set initially */
|
|
if (cs1_enable_initial)
|
|
/* Set SDE_1 */
|
|
setbits_le32(&mmdc0->mdctl, 1 << 30);
|
|
|
|
if (cs0_enable_initial)
|
|
/* Set SDE_0 */
|
|
setbits_le32(&mmdc0->mdctl, 1 << 31);
|
|
|
|
/* Re-enable to auto refresh */
|
|
writel(temp_ref, &mmdc0->mdref);
|
|
|
|
/* Clear the MDSCR (including the con_req bit) */
|
|
writel(0x0, &mmdc0->mdscr); /* CS0 */
|
|
|
|
/* Poll to make sure the con_ack bit is clear */
|
|
wait_for_bit_le32(&mmdc0->mdscr, 1 << 14, 0, 100, 0);
|
|
|
|
/*
|
|
* Print out the registers that were updated as a result
|
|
* of the calibration process.
|
|
*/
|
|
debug("MMDC registers updated from calibration\n");
|
|
debug("Read DQS gating calibration:\n");
|
|
debug("\tMPDGCTRL0 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl0));
|
|
debug("\tMPDGCTRL1 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl1));
|
|
if (sysinfo->dsize == 2) {
|
|
debug("\tMPDGCTRL0 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl0));
|
|
debug("\tMPDGCTRL1 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl1));
|
|
}
|
|
debug("Read calibration:\n");
|
|
debug("\tMPRDDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mprddlctl));
|
|
if (sysinfo->dsize == 2)
|
|
debug("\tMPRDDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mprddlctl));
|
|
debug("Write calibration:\n");
|
|
debug("\tMPWRDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mpwrdlctl));
|
|
if (sysinfo->dsize == 2)
|
|
debug("\tMPWRDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mpwrdlctl));
|
|
|
|
/*
|
|
* Registers below are for debugging purposes. These print out
|
|
* the upper and lower boundaries captured during
|
|
* read DQS gating calibration.
|
|
*/
|
|
debug("Status registers bounds for read DQS gating:\n");
|
|
debug("\tMPDGHWST0 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst0));
|
|
debug("\tMPDGHWST1 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst1));
|
|
debug("\tMPDGHWST2 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst2));
|
|
debug("\tMPDGHWST3 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst3));
|
|
if (sysinfo->dsize == 2) {
|
|
debug("\tMPDGHWST0 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst0));
|
|
debug("\tMPDGHWST1 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst1));
|
|
debug("\tMPDGHWST2 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst2));
|
|
debug("\tMPDGHWST3 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst3));
|
|
}
|
|
|
|
debug("Final do_dqs_calibration error mask: 0x%x\n", errors);
|
|
|
|
return errors;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_MX6SX)
|
|
/* Configure MX6SX mmdc iomux */
|
|
void mx6sx_dram_iocfg(unsigned width,
|
|
const struct mx6sx_iomux_ddr_regs *ddr,
|
|
const struct mx6sx_iomux_grp_regs *grp)
|
|
{
|
|
struct mx6sx_iomux_ddr_regs *mx6_ddr_iomux;
|
|
struct mx6sx_iomux_grp_regs *mx6_grp_iomux;
|
|
|
|
mx6_ddr_iomux = (struct mx6sx_iomux_ddr_regs *)MX6SX_IOM_DDR_BASE;
|
|
mx6_grp_iomux = (struct mx6sx_iomux_grp_regs *)MX6SX_IOM_GRP_BASE;
|
|
|
|
/* DDR IO TYPE */
|
|
writel(grp->grp_ddr_type, &mx6_grp_iomux->grp_ddr_type);
|
|
writel(grp->grp_ddrpke, &mx6_grp_iomux->grp_ddrpke);
|
|
|
|
/* CLOCK */
|
|
writel(ddr->dram_sdclk_0, &mx6_ddr_iomux->dram_sdclk_0);
|
|
|
|
/* ADDRESS */
|
|
writel(ddr->dram_cas, &mx6_ddr_iomux->dram_cas);
|
|
writel(ddr->dram_ras, &mx6_ddr_iomux->dram_ras);
|
|
writel(grp->grp_addds, &mx6_grp_iomux->grp_addds);
|
|
|
|
/* Control */
|
|
writel(ddr->dram_reset, &mx6_ddr_iomux->dram_reset);
|
|
writel(ddr->dram_sdba2, &mx6_ddr_iomux->dram_sdba2);
|
|
writel(ddr->dram_sdcke0, &mx6_ddr_iomux->dram_sdcke0);
|
|
writel(ddr->dram_sdcke1, &mx6_ddr_iomux->dram_sdcke1);
|
|
writel(ddr->dram_odt0, &mx6_ddr_iomux->dram_odt0);
|
|
writel(ddr->dram_odt1, &mx6_ddr_iomux->dram_odt1);
|
|
writel(grp->grp_ctlds, &mx6_grp_iomux->grp_ctlds);
|
|
|
|
/* Data Strobes */
|
|
writel(grp->grp_ddrmode_ctl, &mx6_grp_iomux->grp_ddrmode_ctl);
|
|
writel(ddr->dram_sdqs0, &mx6_ddr_iomux->dram_sdqs0);
|
|
writel(ddr->dram_sdqs1, &mx6_ddr_iomux->dram_sdqs1);
|
|
if (width >= 32) {
|
|
writel(ddr->dram_sdqs2, &mx6_ddr_iomux->dram_sdqs2);
|
|
writel(ddr->dram_sdqs3, &mx6_ddr_iomux->dram_sdqs3);
|
|
}
|
|
|
|
/* Data */
|
|
writel(grp->grp_ddrmode, &mx6_grp_iomux->grp_ddrmode);
|
|
writel(grp->grp_b0ds, &mx6_grp_iomux->grp_b0ds);
|
|
writel(grp->grp_b1ds, &mx6_grp_iomux->grp_b1ds);
|
|
if (width >= 32) {
|
|
writel(grp->grp_b2ds, &mx6_grp_iomux->grp_b2ds);
|
|
writel(grp->grp_b3ds, &mx6_grp_iomux->grp_b3ds);
|
|
}
|
|
writel(ddr->dram_dqm0, &mx6_ddr_iomux->dram_dqm0);
|
|
writel(ddr->dram_dqm1, &mx6_ddr_iomux->dram_dqm1);
|
|
if (width >= 32) {
|
|
writel(ddr->dram_dqm2, &mx6_ddr_iomux->dram_dqm2);
|
|
writel(ddr->dram_dqm3, &mx6_ddr_iomux->dram_dqm3);
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_MX6UL) || defined(CONFIG_MX6ULL)
|
|
void mx6ul_dram_iocfg(unsigned width,
|
|
const struct mx6ul_iomux_ddr_regs *ddr,
|
|
const struct mx6ul_iomux_grp_regs *grp)
|
|
{
|
|
struct mx6ul_iomux_ddr_regs *mx6_ddr_iomux;
|
|
struct mx6ul_iomux_grp_regs *mx6_grp_iomux;
|
|
|
|
mx6_ddr_iomux = (struct mx6ul_iomux_ddr_regs *)MX6UL_IOM_DDR_BASE;
|
|
mx6_grp_iomux = (struct mx6ul_iomux_grp_regs *)MX6UL_IOM_GRP_BASE;
|
|
|
|
/* DDR IO TYPE */
|
|
writel(grp->grp_ddr_type, &mx6_grp_iomux->grp_ddr_type);
|
|
writel(grp->grp_ddrpke, &mx6_grp_iomux->grp_ddrpke);
|
|
|
|
/* CLOCK */
|
|
writel(ddr->dram_sdclk_0, &mx6_ddr_iomux->dram_sdclk_0);
|
|
|
|
/* ADDRESS */
|
|
writel(ddr->dram_cas, &mx6_ddr_iomux->dram_cas);
|
|
writel(ddr->dram_ras, &mx6_ddr_iomux->dram_ras);
|
|
writel(grp->grp_addds, &mx6_grp_iomux->grp_addds);
|
|
|
|
/* Control */
|
|
writel(ddr->dram_reset, &mx6_ddr_iomux->dram_reset);
|
|
writel(ddr->dram_sdba2, &mx6_ddr_iomux->dram_sdba2);
|
|
writel(ddr->dram_odt0, &mx6_ddr_iomux->dram_odt0);
|
|
writel(ddr->dram_odt1, &mx6_ddr_iomux->dram_odt1);
|
|
writel(grp->grp_ctlds, &mx6_grp_iomux->grp_ctlds);
|
|
|
|
/* Data Strobes */
|
|
writel(grp->grp_ddrmode_ctl, &mx6_grp_iomux->grp_ddrmode_ctl);
|
|
writel(ddr->dram_sdqs0, &mx6_ddr_iomux->dram_sdqs0);
|
|
writel(ddr->dram_sdqs1, &mx6_ddr_iomux->dram_sdqs1);
|
|
|
|
/* Data */
|
|
writel(grp->grp_ddrmode, &mx6_grp_iomux->grp_ddrmode);
|
|
writel(grp->grp_b0ds, &mx6_grp_iomux->grp_b0ds);
|
|
writel(grp->grp_b1ds, &mx6_grp_iomux->grp_b1ds);
|
|
writel(ddr->dram_dqm0, &mx6_ddr_iomux->dram_dqm0);
|
|
writel(ddr->dram_dqm1, &mx6_ddr_iomux->dram_dqm1);
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_MX6SL)
|
|
void mx6sl_dram_iocfg(unsigned width,
|
|
const struct mx6sl_iomux_ddr_regs *ddr,
|
|
const struct mx6sl_iomux_grp_regs *grp)
|
|
{
|
|
struct mx6sl_iomux_ddr_regs *mx6_ddr_iomux;
|
|
struct mx6sl_iomux_grp_regs *mx6_grp_iomux;
|
|
|
|
mx6_ddr_iomux = (struct mx6sl_iomux_ddr_regs *)MX6SL_IOM_DDR_BASE;
|
|
mx6_grp_iomux = (struct mx6sl_iomux_grp_regs *)MX6SL_IOM_GRP_BASE;
|
|
|
|
/* DDR IO TYPE */
|
|
mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type;
|
|
mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke;
|
|
|
|
/* CLOCK */
|
|
mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0;
|
|
|
|
/* ADDRESS */
|
|
mx6_ddr_iomux->dram_cas = ddr->dram_cas;
|
|
mx6_ddr_iomux->dram_ras = ddr->dram_ras;
|
|
mx6_grp_iomux->grp_addds = grp->grp_addds;
|
|
|
|
/* Control */
|
|
mx6_ddr_iomux->dram_reset = ddr->dram_reset;
|
|
mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2;
|
|
mx6_grp_iomux->grp_ctlds = grp->grp_ctlds;
|
|
|
|
/* Data Strobes */
|
|
mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl;
|
|
mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0;
|
|
mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1;
|
|
if (width >= 32) {
|
|
mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2;
|
|
mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3;
|
|
}
|
|
|
|
/* Data */
|
|
mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode;
|
|
mx6_grp_iomux->grp_b0ds = grp->grp_b0ds;
|
|
mx6_grp_iomux->grp_b1ds = grp->grp_b1ds;
|
|
if (width >= 32) {
|
|
mx6_grp_iomux->grp_b2ds = grp->grp_b2ds;
|
|
mx6_grp_iomux->grp_b3ds = grp->grp_b3ds;
|
|
}
|
|
|
|
mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0;
|
|
mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1;
|
|
if (width >= 32) {
|
|
mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2;
|
|
mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
|
|
/* Configure MX6DQ mmdc iomux */
|
|
void mx6dq_dram_iocfg(unsigned width,
|
|
const struct mx6dq_iomux_ddr_regs *ddr,
|
|
const struct mx6dq_iomux_grp_regs *grp)
|
|
{
|
|
volatile struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux;
|
|
volatile struct mx6dq_iomux_grp_regs *mx6_grp_iomux;
|
|
|
|
mx6_ddr_iomux = (struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE;
|
|
mx6_grp_iomux = (struct mx6dq_iomux_grp_regs *)MX6DQ_IOM_GRP_BASE;
|
|
|
|
/* DDR IO Type */
|
|
mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type;
|
|
mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke;
|
|
|
|
/* Clock */
|
|
mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0;
|
|
mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1;
|
|
|
|
/* Address */
|
|
mx6_ddr_iomux->dram_cas = ddr->dram_cas;
|
|
mx6_ddr_iomux->dram_ras = ddr->dram_ras;
|
|
mx6_grp_iomux->grp_addds = grp->grp_addds;
|
|
|
|
/* Control */
|
|
mx6_ddr_iomux->dram_reset = ddr->dram_reset;
|
|
mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0;
|
|
mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1;
|
|
mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2;
|
|
mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0;
|
|
mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1;
|
|
mx6_grp_iomux->grp_ctlds = grp->grp_ctlds;
|
|
|
|
/* Data Strobes */
|
|
mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl;
|
|
mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0;
|
|
mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1;
|
|
if (width >= 32) {
|
|
mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2;
|
|
mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3;
|
|
}
|
|
if (width >= 64) {
|
|
mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4;
|
|
mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5;
|
|
mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6;
|
|
mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7;
|
|
}
|
|
|
|
/* Data */
|
|
mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode;
|
|
mx6_grp_iomux->grp_b0ds = grp->grp_b0ds;
|
|
mx6_grp_iomux->grp_b1ds = grp->grp_b1ds;
|
|
if (width >= 32) {
|
|
mx6_grp_iomux->grp_b2ds = grp->grp_b2ds;
|
|
mx6_grp_iomux->grp_b3ds = grp->grp_b3ds;
|
|
}
|
|
if (width >= 64) {
|
|
mx6_grp_iomux->grp_b4ds = grp->grp_b4ds;
|
|
mx6_grp_iomux->grp_b5ds = grp->grp_b5ds;
|
|
mx6_grp_iomux->grp_b6ds = grp->grp_b6ds;
|
|
mx6_grp_iomux->grp_b7ds = grp->grp_b7ds;
|
|
}
|
|
mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0;
|
|
mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1;
|
|
if (width >= 32) {
|
|
mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2;
|
|
mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3;
|
|
}
|
|
if (width >= 64) {
|
|
mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4;
|
|
mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5;
|
|
mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6;
|
|
mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
|
|
/* Configure MX6SDL mmdc iomux */
|
|
void mx6sdl_dram_iocfg(unsigned width,
|
|
const struct mx6sdl_iomux_ddr_regs *ddr,
|
|
const struct mx6sdl_iomux_grp_regs *grp)
|
|
{
|
|
volatile struct mx6sdl_iomux_ddr_regs *mx6_ddr_iomux;
|
|
volatile struct mx6sdl_iomux_grp_regs *mx6_grp_iomux;
|
|
|
|
mx6_ddr_iomux = (struct mx6sdl_iomux_ddr_regs *)MX6SDL_IOM_DDR_BASE;
|
|
mx6_grp_iomux = (struct mx6sdl_iomux_grp_regs *)MX6SDL_IOM_GRP_BASE;
|
|
|
|
/* DDR IO Type */
|
|
mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type;
|
|
mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke;
|
|
|
|
/* Clock */
|
|
mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0;
|
|
mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1;
|
|
|
|
/* Address */
|
|
mx6_ddr_iomux->dram_cas = ddr->dram_cas;
|
|
mx6_ddr_iomux->dram_ras = ddr->dram_ras;
|
|
mx6_grp_iomux->grp_addds = grp->grp_addds;
|
|
|
|
/* Control */
|
|
mx6_ddr_iomux->dram_reset = ddr->dram_reset;
|
|
mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0;
|
|
mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1;
|
|
mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2;
|
|
mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0;
|
|
mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1;
|
|
mx6_grp_iomux->grp_ctlds = grp->grp_ctlds;
|
|
|
|
/* Data Strobes */
|
|
mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl;
|
|
mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0;
|
|
mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1;
|
|
if (width >= 32) {
|
|
mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2;
|
|
mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3;
|
|
}
|
|
if (width >= 64) {
|
|
mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4;
|
|
mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5;
|
|
mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6;
|
|
mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7;
|
|
}
|
|
|
|
/* Data */
|
|
mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode;
|
|
mx6_grp_iomux->grp_b0ds = grp->grp_b0ds;
|
|
mx6_grp_iomux->grp_b1ds = grp->grp_b1ds;
|
|
if (width >= 32) {
|
|
mx6_grp_iomux->grp_b2ds = grp->grp_b2ds;
|
|
mx6_grp_iomux->grp_b3ds = grp->grp_b3ds;
|
|
}
|
|
if (width >= 64) {
|
|
mx6_grp_iomux->grp_b4ds = grp->grp_b4ds;
|
|
mx6_grp_iomux->grp_b5ds = grp->grp_b5ds;
|
|
mx6_grp_iomux->grp_b6ds = grp->grp_b6ds;
|
|
mx6_grp_iomux->grp_b7ds = grp->grp_b7ds;
|
|
}
|
|
mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0;
|
|
mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1;
|
|
if (width >= 32) {
|
|
mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2;
|
|
mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3;
|
|
}
|
|
if (width >= 64) {
|
|
mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4;
|
|
mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5;
|
|
mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6;
|
|
mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* Configure mx6 mmdc registers based on:
|
|
* - board-specific memory configuration
|
|
* - board-specific calibration data
|
|
* - ddr3/lpddr2 chip details
|
|
*
|
|
* The various calculations here are derived from the Freescale
|
|
* 1. i.Mx6DQSDL DDR3 Script Aid spreadsheet (DOC-94917) designed to generate
|
|
* MMDC configuration registers based on memory system and memory chip
|
|
* parameters.
|
|
*
|
|
* 2. i.Mx6SL LPDDR2 Script Aid spreadsheet V0.04 designed to generate MMDC
|
|
* configuration registers based on memory system and memory chip
|
|
* parameters.
|
|
*
|
|
* The defaults here are those which were specified in the spreadsheet.
|
|
* For details on each register, refer to the IMX6DQRM and/or IMX6SDLRM
|
|
* and/or IMX6SLRM section titled MMDC initialization.
|
|
*/
|
|
#define MR(val, ba, cmd, cs1) \
|
|
((val << 16) | (1 << 15) | (cmd << 4) | (cs1 << 3) | ba)
|
|
#define MMDC1(entry, value) do { \
|
|
if (!is_mx6sx() && !is_mx6ul() && !is_mx6ull() && !is_mx6sl()) \
|
|
mmdc1->entry = value; \
|
|
} while (0)
|
|
|
|
/*
|
|
* According JESD209-2B-LPDDR2: Table 103
|
|
* WL: write latency
|
|
*/
|
|
static int lpddr2_wl(uint32_t mem_speed)
|
|
{
|
|
switch (mem_speed) {
|
|
case 1066:
|
|
case 933:
|
|
return 4;
|
|
case 800:
|
|
return 3;
|
|
case 677:
|
|
case 533:
|
|
return 2;
|
|
case 400:
|
|
case 333:
|
|
return 1;
|
|
default:
|
|
puts("invalid memory speed\n");
|
|
hang();
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* According JESD209-2B-LPDDR2: Table 103
|
|
* RL: read latency
|
|
*/
|
|
static int lpddr2_rl(uint32_t mem_speed)
|
|
{
|
|
switch (mem_speed) {
|
|
case 1066:
|
|
return 8;
|
|
case 933:
|
|
return 7;
|
|
case 800:
|
|
return 6;
|
|
case 677:
|
|
return 5;
|
|
case 533:
|
|
return 4;
|
|
case 400:
|
|
case 333:
|
|
return 3;
|
|
default:
|
|
puts("invalid memory speed\n");
|
|
hang();
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
void mx6_lpddr2_cfg(const struct mx6_ddr_sysinfo *sysinfo,
|
|
const struct mx6_mmdc_calibration *calib,
|
|
const struct mx6_lpddr2_cfg *lpddr2_cfg)
|
|
{
|
|
volatile struct mmdc_p_regs *mmdc0;
|
|
u32 val;
|
|
u8 tcke, tcksrx, tcksre, trrd;
|
|
u8 twl, txp, tfaw, tcl;
|
|
u16 tras, twr, tmrd, trtp, twtr, trfc, txsr;
|
|
u16 trcd_lp, trppb_lp, trpab_lp, trc_lp;
|
|
u16 cs0_end;
|
|
u8 coladdr;
|
|
int clkper; /* clock period in picoseconds */
|
|
int clock; /* clock freq in mHz */
|
|
int cs;
|
|
|
|
/* only support 16/32 bits */
|
|
if (sysinfo->dsize > 1)
|
|
hang();
|
|
|
|
mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
|
|
clock = mxc_get_clock(MXC_DDR_CLK) / 1000000U;
|
|
clkper = (1000 * 1000) / clock; /* pico seconds */
|
|
|
|
twl = lpddr2_wl(lpddr2_cfg->mem_speed) - 1;
|
|
|
|
/* LPDDR2-S2 and LPDDR2-S4 have the same tRFC value. */
|
|
switch (lpddr2_cfg->density) {
|
|
case 1:
|
|
case 2:
|
|
case 4:
|
|
trfc = DIV_ROUND_UP(130000, clkper) - 1;
|
|
txsr = DIV_ROUND_UP(140000, clkper) - 1;
|
|
break;
|
|
case 8:
|
|
trfc = DIV_ROUND_UP(210000, clkper) - 1;
|
|
txsr = DIV_ROUND_UP(220000, clkper) - 1;
|
|
break;
|
|
default:
|
|
/*
|
|
* 64Mb, 128Mb, 256Mb, 512Mb are not supported currently.
|
|
*/
|
|
hang();
|
|
break;
|
|
}
|
|
/*
|
|
* txpdll, txpr, taonpd and taofpd are not relevant in LPDDR2 mode,
|
|
* set them to 0. */
|
|
txp = DIV_ROUND_UP(7500, clkper) - 1;
|
|
tcke = 3;
|
|
if (lpddr2_cfg->mem_speed == 333)
|
|
tfaw = DIV_ROUND_UP(60000, clkper) - 1;
|
|
else
|
|
tfaw = DIV_ROUND_UP(50000, clkper) - 1;
|
|
trrd = DIV_ROUND_UP(10000, clkper) - 1;
|
|
|
|
/* tckesr for LPDDR2 */
|
|
tcksre = DIV_ROUND_UP(15000, clkper);
|
|
tcksrx = tcksre;
|
|
twr = DIV_ROUND_UP(15000, clkper) - 1;
|
|
/*
|
|
* tMRR: 2, tMRW: 5
|
|
* tMRD should be set to max(tMRR, tMRW)
|
|
*/
|
|
tmrd = 5;
|
|
tras = DIV_ROUND_UP(lpddr2_cfg->trasmin, clkper / 10) - 1;
|
|
/* LPDDR2 mode use tRCD_LP filed in MDCFG3. */
|
|
trcd_lp = DIV_ROUND_UP(lpddr2_cfg->trcd_lp, clkper / 10) - 1;
|
|
trc_lp = DIV_ROUND_UP(lpddr2_cfg->trasmin + lpddr2_cfg->trppb_lp,
|
|
clkper / 10) - 1;
|
|
trppb_lp = DIV_ROUND_UP(lpddr2_cfg->trppb_lp, clkper / 10) - 1;
|
|
trpab_lp = DIV_ROUND_UP(lpddr2_cfg->trpab_lp, clkper / 10) - 1;
|
|
/* To LPDDR2, CL in MDCFG0 refers to RL */
|
|
tcl = lpddr2_rl(lpddr2_cfg->mem_speed) - 3;
|
|
twtr = DIV_ROUND_UP(7500, clkper) - 1;
|
|
trtp = DIV_ROUND_UP(7500, clkper) - 1;
|
|
|
|
cs0_end = 4 * sysinfo->cs_density - 1;
|
|
|
|
debug("density:%d Gb (%d Gb per chip)\n",
|
|
sysinfo->cs_density, lpddr2_cfg->density);
|
|
debug("clock: %dMHz (%d ps)\n", clock, clkper);
|
|
debug("memspd:%d\n", lpddr2_cfg->mem_speed);
|
|
debug("trcd_lp=%d\n", trcd_lp);
|
|
debug("trppb_lp=%d\n", trppb_lp);
|
|
debug("trpab_lp=%d\n", trpab_lp);
|
|
debug("trc_lp=%d\n", trc_lp);
|
|
debug("tcke=%d\n", tcke);
|
|
debug("tcksrx=%d\n", tcksrx);
|
|
debug("tcksre=%d\n", tcksre);
|
|
debug("trfc=%d\n", trfc);
|
|
debug("txsr=%d\n", txsr);
|
|
debug("txp=%d\n", txp);
|
|
debug("tfaw=%d\n", tfaw);
|
|
debug("tcl=%d\n", tcl);
|
|
debug("tras=%d\n", tras);
|
|
debug("twr=%d\n", twr);
|
|
debug("tmrd=%d\n", tmrd);
|
|
debug("twl=%d\n", twl);
|
|
debug("trtp=%d\n", trtp);
|
|
debug("twtr=%d\n", twtr);
|
|
debug("trrd=%d\n", trrd);
|
|
debug("cs0_end=%d\n", cs0_end);
|
|
debug("ncs=%d\n", sysinfo->ncs);
|
|
|
|
/*
|
|
* board-specific configuration:
|
|
* These values are determined empirically and vary per board layout
|
|
*/
|
|
mmdc0->mpwldectrl0 = calib->p0_mpwldectrl0;
|
|
mmdc0->mpwldectrl1 = calib->p0_mpwldectrl1;
|
|
mmdc0->mpdgctrl0 = calib->p0_mpdgctrl0;
|
|
mmdc0->mpdgctrl1 = calib->p0_mpdgctrl1;
|
|
mmdc0->mprddlctl = calib->p0_mprddlctl;
|
|
mmdc0->mpwrdlctl = calib->p0_mpwrdlctl;
|
|
mmdc0->mpzqlp2ctl = calib->mpzqlp2ctl;
|
|
|
|
/* Read data DQ Byte0-3 delay */
|
|
mmdc0->mprddqby0dl = 0x33333333;
|
|
mmdc0->mprddqby1dl = 0x33333333;
|
|
if (sysinfo->dsize > 0) {
|
|
mmdc0->mprddqby2dl = 0x33333333;
|
|
mmdc0->mprddqby3dl = 0x33333333;
|
|
}
|
|
|
|
/* Write data DQ Byte0-3 delay */
|
|
mmdc0->mpwrdqby0dl = 0xf3333333;
|
|
mmdc0->mpwrdqby1dl = 0xf3333333;
|
|
if (sysinfo->dsize > 0) {
|
|
mmdc0->mpwrdqby2dl = 0xf3333333;
|
|
mmdc0->mpwrdqby3dl = 0xf3333333;
|
|
}
|
|
|
|
/*
|
|
* In LPDDR2 mode this register should be cleared,
|
|
* so no termination will be activated.
|
|
*/
|
|
mmdc0->mpodtctrl = 0;
|
|
|
|
/* complete calibration */
|
|
val = (1 << 11); /* Force measurement on delay-lines */
|
|
mmdc0->mpmur0 = val;
|
|
|
|
/* Step 1: configuration request */
|
|
mmdc0->mdscr = (u32)(1 << 15); /* config request */
|
|
|
|
/* Step 2: Timing configuration */
|
|
mmdc0->mdcfg0 = (trfc << 24) | (txsr << 16) | (txp << 13) |
|
|
(tfaw << 4) | tcl;
|
|
mmdc0->mdcfg1 = (tras << 16) | (twr << 9) | (tmrd << 5) | twl;
|
|
mmdc0->mdcfg2 = (trtp << 6) | (twtr << 3) | trrd;
|
|
mmdc0->mdcfg3lp = (trc_lp << 16) | (trcd_lp << 8) |
|
|
(trppb_lp << 4) | trpab_lp;
|
|
mmdc0->mdotc = 0;
|
|
|
|
mmdc0->mdasp = cs0_end; /* CS addressing */
|
|
|
|
/* Step 3: Configure DDR type */
|
|
mmdc0->mdmisc = (sysinfo->cs1_mirror << 19) | (sysinfo->walat << 16) |
|
|
(sysinfo->bi_on << 12) | (sysinfo->mif3_mode << 9) |
|
|
(sysinfo->ralat << 6) | (1 << 3);
|
|
|
|
/* Step 4: Configure delay while leaving reset */
|
|
mmdc0->mdor = (sysinfo->sde_to_rst << 8) |
|
|
(sysinfo->rst_to_cke << 0);
|
|
|
|
/* Step 5: Configure DDR physical parameters (density and burst len) */
|
|
coladdr = lpddr2_cfg->coladdr;
|
|
if (lpddr2_cfg->coladdr == 8) /* 8-bit COL is 0x3 */
|
|
coladdr += 4;
|
|
else if (lpddr2_cfg->coladdr == 12) /* 12-bit COL is 0x4 */
|
|
coladdr += 1;
|
|
mmdc0->mdctl = (lpddr2_cfg->rowaddr - 11) << 24 | /* ROW */
|
|
(coladdr - 9) << 20 | /* COL */
|
|
(0 << 19) | /* Burst Length = 4 for LPDDR2 */
|
|
(sysinfo->dsize << 16); /* DDR data bus size */
|
|
|
|
/* Step 6: Perform ZQ calibration */
|
|
val = 0xa1390003; /* one-time HW ZQ calib */
|
|
mmdc0->mpzqhwctrl = val;
|
|
|
|
/* Step 7: Enable MMDC with desired chip select */
|
|
mmdc0->mdctl |= (1 << 31) | /* SDE_0 for CS0 */
|
|
((sysinfo->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */
|
|
|
|
/* Step 8: Write Mode Registers to Init LPDDR2 devices */
|
|
for (cs = 0; cs < sysinfo->ncs; cs++) {
|
|
/* MR63: reset */
|
|
mmdc0->mdscr = MR(63, 0, 3, cs);
|
|
/* MR10: calibration,
|
|
* 0xff is calibration command after intilization.
|
|
*/
|
|
val = 0xA | (0xff << 8);
|
|
mmdc0->mdscr = MR(val, 0, 3, cs);
|
|
/* MR1 */
|
|
val = 0x1 | (0x82 << 8);
|
|
mmdc0->mdscr = MR(val, 0, 3, cs);
|
|
/* MR2 */
|
|
val = 0x2 | (0x04 << 8);
|
|
mmdc0->mdscr = MR(val, 0, 3, cs);
|
|
/* MR3 */
|
|
val = 0x3 | (0x02 << 8);
|
|
mmdc0->mdscr = MR(val, 0, 3, cs);
|
|
}
|
|
|
|
/* Step 10: Power down control and self-refresh */
|
|
mmdc0->mdpdc = (tcke & 0x7) << 16 |
|
|
5 << 12 | /* PWDT_1: 256 cycles */
|
|
5 << 8 | /* PWDT_0: 256 cycles */
|
|
1 << 6 | /* BOTH_CS_PD */
|
|
(tcksrx & 0x7) << 3 |
|
|
(tcksre & 0x7);
|
|
mmdc0->mapsr = 0x00001006; /* ADOPT power down enabled */
|
|
|
|
/* Step 11: Configure ZQ calibration: one-time and periodic 1ms */
|
|
val = 0xa1310003;
|
|
mmdc0->mpzqhwctrl = val;
|
|
|
|
/* Step 12: Configure and activate periodic refresh */
|
|
mmdc0->mdref = (sysinfo->refsel << 14) | (sysinfo->refr << 11);
|
|
|
|
/* Step 13: Deassert config request - init complete */
|
|
mmdc0->mdscr = 0x00000000;
|
|
|
|
/* wait for auto-ZQ calibration to complete */
|
|
mdelay(1);
|
|
}
|
|
|
|
void mx6_ddr3_cfg(const struct mx6_ddr_sysinfo *sysinfo,
|
|
const struct mx6_mmdc_calibration *calib,
|
|
const struct mx6_ddr3_cfg *ddr3_cfg)
|
|
{
|
|
volatile struct mmdc_p_regs *mmdc0;
|
|
volatile struct mmdc_p_regs *mmdc1;
|
|
u32 val;
|
|
u8 tcke, tcksrx, tcksre, txpdll, taofpd, taonpd, trrd;
|
|
u8 todtlon, taxpd, tanpd, tcwl, txp, tfaw, tcl;
|
|
u8 todt_idle_off = 0x4; /* from DDR3 Script Aid spreadsheet */
|
|
u16 trcd, trc, tras, twr, tmrd, trtp, trp, twtr, trfc, txs, txpr;
|
|
u16 cs0_end;
|
|
u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */
|
|
u8 coladdr;
|
|
int clkper; /* clock period in picoseconds */
|
|
int clock; /* clock freq in MHz */
|
|
int cs;
|
|
u16 mem_speed = ddr3_cfg->mem_speed;
|
|
|
|
mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
if (!is_mx6sx() && !is_mx6ul() && !is_mx6ull() && !is_mx6sl())
|
|
mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
|
|
|
/* Limit mem_speed for MX6D/MX6Q */
|
|
if (is_mx6dq() || is_mx6dqp()) {
|
|
if (mem_speed > 1066)
|
|
mem_speed = 1066; /* 1066 MT/s */
|
|
|
|
tcwl = 4;
|
|
}
|
|
/* Limit mem_speed for MX6S/MX6DL */
|
|
else {
|
|
if (mem_speed > 800)
|
|
mem_speed = 800; /* 800 MT/s */
|
|
|
|
tcwl = 3;
|
|
}
|
|
|
|
clock = mem_speed / 2;
|
|
/*
|
|
* Data rate of 1066 MT/s requires 533 MHz DDR3 clock, but MX6D/Q supports
|
|
* up to 528 MHz, so reduce the clock to fit chip specs
|
|
*/
|
|
if (is_mx6dq() || is_mx6dqp()) {
|
|
if (clock > 528)
|
|
clock = 528; /* 528 MHz */
|
|
}
|
|
|
|
clkper = (1000 * 1000) / clock; /* pico seconds */
|
|
todtlon = tcwl;
|
|
taxpd = tcwl;
|
|
tanpd = tcwl;
|
|
|
|
switch (ddr3_cfg->density) {
|
|
case 1: /* 1Gb per chip */
|
|
trfc = DIV_ROUND_UP(110000, clkper) - 1;
|
|
txs = DIV_ROUND_UP(120000, clkper) - 1;
|
|
break;
|
|
case 2: /* 2Gb per chip */
|
|
trfc = DIV_ROUND_UP(160000, clkper) - 1;
|
|
txs = DIV_ROUND_UP(170000, clkper) - 1;
|
|
break;
|
|
case 4: /* 4Gb per chip */
|
|
trfc = DIV_ROUND_UP(260000, clkper) - 1;
|
|
txs = DIV_ROUND_UP(270000, clkper) - 1;
|
|
break;
|
|
case 8: /* 8Gb per chip */
|
|
trfc = DIV_ROUND_UP(350000, clkper) - 1;
|
|
txs = DIV_ROUND_UP(360000, clkper) - 1;
|
|
break;
|
|
default:
|
|
/* invalid density */
|
|
puts("invalid chip density\n");
|
|
hang();
|
|
break;
|
|
}
|
|
txpr = txs;
|
|
|
|
switch (mem_speed) {
|
|
case 800:
|
|
txp = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1;
|
|
tcke = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1;
|
|
if (ddr3_cfg->pagesz == 1) {
|
|
tfaw = DIV_ROUND_UP(40000, clkper) - 1;
|
|
trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1;
|
|
} else {
|
|
tfaw = DIV_ROUND_UP(50000, clkper) - 1;
|
|
trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1;
|
|
}
|
|
break;
|
|
case 1066:
|
|
txp = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1;
|
|
tcke = DIV_ROUND_UP(max(3 * clkper, 5625), clkper) - 1;
|
|
if (ddr3_cfg->pagesz == 1) {
|
|
tfaw = DIV_ROUND_UP(37500, clkper) - 1;
|
|
trrd = DIV_ROUND_UP(max(4 * clkper, 7500), clkper) - 1;
|
|
} else {
|
|
tfaw = DIV_ROUND_UP(50000, clkper) - 1;
|
|
trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1;
|
|
}
|
|
break;
|
|
default:
|
|
puts("invalid memory speed\n");
|
|
hang();
|
|
break;
|
|
}
|
|
txpdll = DIV_ROUND_UP(max(10 * clkper, 24000), clkper) - 1;
|
|
tcksre = DIV_ROUND_UP(max(5 * clkper, 10000), clkper);
|
|
taonpd = DIV_ROUND_UP(2000, clkper) - 1;
|
|
tcksrx = tcksre;
|
|
taofpd = taonpd;
|
|
twr = DIV_ROUND_UP(15000, clkper) - 1;
|
|
tmrd = DIV_ROUND_UP(max(12 * clkper, 15000), clkper) - 1;
|
|
trc = DIV_ROUND_UP(ddr3_cfg->trcmin, clkper / 10) - 1;
|
|
tras = DIV_ROUND_UP(ddr3_cfg->trasmin, clkper / 10) - 1;
|
|
tcl = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 3;
|
|
trp = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 1;
|
|
twtr = ROUND(max(4 * clkper, 7500) / clkper, 1) - 1;
|
|
trcd = trp;
|
|
trtp = twtr;
|
|
cs0_end = 4 * sysinfo->cs_density - 1;
|
|
|
|
debug("density:%d Gb (%d Gb per chip)\n",
|
|
sysinfo->cs_density, ddr3_cfg->density);
|
|
debug("clock: %dMHz (%d ps)\n", clock, clkper);
|
|
debug("memspd:%d\n", mem_speed);
|
|
debug("tcke=%d\n", tcke);
|
|
debug("tcksrx=%d\n", tcksrx);
|
|
debug("tcksre=%d\n", tcksre);
|
|
debug("taofpd=%d\n", taofpd);
|
|
debug("taonpd=%d\n", taonpd);
|
|
debug("todtlon=%d\n", todtlon);
|
|
debug("tanpd=%d\n", tanpd);
|
|
debug("taxpd=%d\n", taxpd);
|
|
debug("trfc=%d\n", trfc);
|
|
debug("txs=%d\n", txs);
|
|
debug("txp=%d\n", txp);
|
|
debug("txpdll=%d\n", txpdll);
|
|
debug("tfaw=%d\n", tfaw);
|
|
debug("tcl=%d\n", tcl);
|
|
debug("trcd=%d\n", trcd);
|
|
debug("trp=%d\n", trp);
|
|
debug("trc=%d\n", trc);
|
|
debug("tras=%d\n", tras);
|
|
debug("twr=%d\n", twr);
|
|
debug("tmrd=%d\n", tmrd);
|
|
debug("tcwl=%d\n", tcwl);
|
|
debug("tdllk=%d\n", tdllk);
|
|
debug("trtp=%d\n", trtp);
|
|
debug("twtr=%d\n", twtr);
|
|
debug("trrd=%d\n", trrd);
|
|
debug("txpr=%d\n", txpr);
|
|
debug("cs0_end=%d\n", cs0_end);
|
|
debug("ncs=%d\n", sysinfo->ncs);
|
|
debug("Rtt_wr=%d\n", sysinfo->rtt_wr);
|
|
debug("Rtt_nom=%d\n", sysinfo->rtt_nom);
|
|
debug("SRT=%d\n", ddr3_cfg->SRT);
|
|
debug("twr=%d\n", twr);
|
|
|
|
/*
|
|
* board-specific configuration:
|
|
* These values are determined empirically and vary per board layout
|
|
* see:
|
|
* appnote, ddr3 spreadsheet
|
|
*/
|
|
mmdc0->mpwldectrl0 = calib->p0_mpwldectrl0;
|
|
mmdc0->mpwldectrl1 = calib->p0_mpwldectrl1;
|
|
mmdc0->mpdgctrl0 = calib->p0_mpdgctrl0;
|
|
mmdc0->mpdgctrl1 = calib->p0_mpdgctrl1;
|
|
mmdc0->mprddlctl = calib->p0_mprddlctl;
|
|
mmdc0->mpwrdlctl = calib->p0_mpwrdlctl;
|
|
if (sysinfo->dsize > 1) {
|
|
MMDC1(mpwldectrl0, calib->p1_mpwldectrl0);
|
|
MMDC1(mpwldectrl1, calib->p1_mpwldectrl1);
|
|
MMDC1(mpdgctrl0, calib->p1_mpdgctrl0);
|
|
MMDC1(mpdgctrl1, calib->p1_mpdgctrl1);
|
|
MMDC1(mprddlctl, calib->p1_mprddlctl);
|
|
MMDC1(mpwrdlctl, calib->p1_mpwrdlctl);
|
|
}
|
|
|
|
/* Read data DQ Byte0-3 delay */
|
|
mmdc0->mprddqby0dl = 0x33333333;
|
|
mmdc0->mprddqby1dl = 0x33333333;
|
|
if (sysinfo->dsize > 0) {
|
|
mmdc0->mprddqby2dl = 0x33333333;
|
|
mmdc0->mprddqby3dl = 0x33333333;
|
|
}
|
|
|
|
if (sysinfo->dsize > 1) {
|
|
MMDC1(mprddqby0dl, 0x33333333);
|
|
MMDC1(mprddqby1dl, 0x33333333);
|
|
MMDC1(mprddqby2dl, 0x33333333);
|
|
MMDC1(mprddqby3dl, 0x33333333);
|
|
}
|
|
|
|
/* MMDC Termination: rtt_nom:2 RZQ/2(120ohm), rtt_nom:1 RZQ/4(60ohm) */
|
|
val = (sysinfo->rtt_nom == 2) ? 0x00011117 : 0x00022227;
|
|
mmdc0->mpodtctrl = val;
|
|
if (sysinfo->dsize > 1)
|
|
MMDC1(mpodtctrl, val);
|
|
|
|
/* complete calibration */
|
|
val = (1 << 11); /* Force measurement on delay-lines */
|
|
mmdc0->mpmur0 = val;
|
|
if (sysinfo->dsize > 1)
|
|
MMDC1(mpmur0, val);
|
|
|
|
/* Step 1: configuration request */
|
|
mmdc0->mdscr = (u32)(1 << 15); /* config request */
|
|
|
|
/* Step 2: Timing configuration */
|
|
mmdc0->mdcfg0 = (trfc << 24) | (txs << 16) | (txp << 13) |
|
|
(txpdll << 9) | (tfaw << 4) | tcl;
|
|
mmdc0->mdcfg1 = (trcd << 29) | (trp << 26) | (trc << 21) |
|
|
(tras << 16) | (1 << 15) /* trpa */ |
|
|
(twr << 9) | (tmrd << 5) | tcwl;
|
|
mmdc0->mdcfg2 = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd;
|
|
mmdc0->mdotc = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) |
|
|
(taxpd << 16) | (todtlon << 12) | (todt_idle_off << 4);
|
|
mmdc0->mdasp = cs0_end; /* CS addressing */
|
|
|
|
/* Step 3: Configure DDR type */
|
|
mmdc0->mdmisc = (sysinfo->cs1_mirror << 19) | (sysinfo->walat << 16) |
|
|
(sysinfo->bi_on << 12) | (sysinfo->mif3_mode << 9) |
|
|
(sysinfo->ralat << 6);
|
|
|
|
/* Step 4: Configure delay while leaving reset */
|
|
mmdc0->mdor = (txpr << 16) | (sysinfo->sde_to_rst << 8) |
|
|
(sysinfo->rst_to_cke << 0);
|
|
|
|
/* Step 5: Configure DDR physical parameters (density and burst len) */
|
|
coladdr = ddr3_cfg->coladdr;
|
|
if (ddr3_cfg->coladdr == 8) /* 8-bit COL is 0x3 */
|
|
coladdr += 4;
|
|
else if (ddr3_cfg->coladdr == 12) /* 12-bit COL is 0x4 */
|
|
coladdr += 1;
|
|
mmdc0->mdctl = (ddr3_cfg->rowaddr - 11) << 24 | /* ROW */
|
|
(coladdr - 9) << 20 | /* COL */
|
|
(1 << 19) | /* Burst Length = 8 for DDR3 */
|
|
(sysinfo->dsize << 16); /* DDR data bus size */
|
|
|
|
/* Step 6: Perform ZQ calibration */
|
|
val = 0xa1390001; /* one-time HW ZQ calib */
|
|
mmdc0->mpzqhwctrl = val;
|
|
if (sysinfo->dsize > 1)
|
|
MMDC1(mpzqhwctrl, val);
|
|
|
|
/* Step 7: Enable MMDC with desired chip select */
|
|
mmdc0->mdctl |= (1 << 31) | /* SDE_0 for CS0 */
|
|
((sysinfo->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */
|
|
|
|
/* Step 8: Write Mode Registers to Init DDR3 devices */
|
|
for (cs = 0; cs < sysinfo->ncs; cs++) {
|
|
/* MR2 */
|
|
val = (sysinfo->rtt_wr & 3) << 9 | (ddr3_cfg->SRT & 1) << 7 |
|
|
((tcwl - 3) & 3) << 3;
|
|
debug("MR2 CS%d: 0x%08x\n", cs, (u32)MR(val, 2, 3, cs));
|
|
mmdc0->mdscr = MR(val, 2, 3, cs);
|
|
/* MR3 */
|
|
debug("MR3 CS%d: 0x%08x\n", cs, (u32)MR(0, 3, 3, cs));
|
|
mmdc0->mdscr = MR(0, 3, 3, cs);
|
|
/* MR1 */
|
|
val = ((sysinfo->rtt_nom & 1) ? 1 : 0) << 2 |
|
|
((sysinfo->rtt_nom & 2) ? 1 : 0) << 6;
|
|
debug("MR1 CS%d: 0x%08x\n", cs, (u32)MR(val, 1, 3, cs));
|
|
mmdc0->mdscr = MR(val, 1, 3, cs);
|
|
/* MR0 */
|
|
val = ((tcl - 1) << 4) | /* CAS */
|
|
(1 << 8) | /* DLL Reset */
|
|
((twr - 3) << 9) | /* Write Recovery */
|
|
(sysinfo->pd_fast_exit << 12); /* Precharge PD PLL on */
|
|
debug("MR0 CS%d: 0x%08x\n", cs, (u32)MR(val, 0, 3, cs));
|
|
mmdc0->mdscr = MR(val, 0, 3, cs);
|
|
/* ZQ calibration */
|
|
val = (1 << 10);
|
|
mmdc0->mdscr = MR(val, 0, 4, cs);
|
|
}
|
|
|
|
/* Step 10: Power down control and self-refresh */
|
|
mmdc0->mdpdc = (tcke & 0x7) << 16 |
|
|
5 << 12 | /* PWDT_1: 256 cycles */
|
|
5 << 8 | /* PWDT_0: 256 cycles */
|
|
1 << 6 | /* BOTH_CS_PD */
|
|
(tcksrx & 0x7) << 3 |
|
|
(tcksre & 0x7);
|
|
if (!sysinfo->pd_fast_exit)
|
|
mmdc0->mdpdc |= (1 << 7); /* SLOW_PD */
|
|
mmdc0->mapsr = 0x00001006; /* ADOPT power down enabled */
|
|
|
|
/* Step 11: Configure ZQ calibration: one-time and periodic 1ms */
|
|
val = 0xa1390003;
|
|
mmdc0->mpzqhwctrl = val;
|
|
if (sysinfo->dsize > 1)
|
|
MMDC1(mpzqhwctrl, val);
|
|
|
|
/* Step 12: Configure and activate periodic refresh */
|
|
mmdc0->mdref = (sysinfo->refsel << 14) | (sysinfo->refr << 11);
|
|
|
|
/* Step 13: Deassert config request - init complete */
|
|
mmdc0->mdscr = 0x00000000;
|
|
|
|
/* wait for auto-ZQ calibration to complete */
|
|
mdelay(1);
|
|
}
|
|
|
|
void mmdc_read_calibration(struct mx6_ddr_sysinfo const *sysinfo,
|
|
struct mx6_mmdc_calibration *calib)
|
|
{
|
|
struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
|
|
struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
|
|
|
|
calib->p0_mpwldectrl0 = readl(&mmdc0->mpwldectrl0);
|
|
calib->p0_mpwldectrl1 = readl(&mmdc0->mpwldectrl1);
|
|
calib->p0_mpdgctrl0 = readl(&mmdc0->mpdgctrl0);
|
|
calib->p0_mpdgctrl1 = readl(&mmdc0->mpdgctrl1);
|
|
calib->p0_mprddlctl = readl(&mmdc0->mprddlctl);
|
|
calib->p0_mpwrdlctl = readl(&mmdc0->mpwrdlctl);
|
|
|
|
if (sysinfo->dsize == 2) {
|
|
calib->p1_mpwldectrl0 = readl(&mmdc1->mpwldectrl0);
|
|
calib->p1_mpwldectrl1 = readl(&mmdc1->mpwldectrl1);
|
|
calib->p1_mpdgctrl0 = readl(&mmdc1->mpdgctrl0);
|
|
calib->p1_mpdgctrl1 = readl(&mmdc1->mpdgctrl1);
|
|
calib->p1_mprddlctl = readl(&mmdc1->mprddlctl);
|
|
calib->p1_mpwrdlctl = readl(&mmdc1->mpwrdlctl);
|
|
}
|
|
}
|
|
|
|
void mx6_dram_cfg(const struct mx6_ddr_sysinfo *sysinfo,
|
|
const struct mx6_mmdc_calibration *calib,
|
|
const void *ddr_cfg)
|
|
{
|
|
if (sysinfo->ddr_type == DDR_TYPE_DDR3) {
|
|
mx6_ddr3_cfg(sysinfo, calib, ddr_cfg);
|
|
} else if (sysinfo->ddr_type == DDR_TYPE_LPDDR2) {
|
|
mx6_lpddr2_cfg(sysinfo, calib, ddr_cfg);
|
|
} else {
|
|
puts("Unsupported ddr type\n");
|
|
hang();
|
|
}
|
|
}
|