u-boot/include/configs/uniphier.h
Masahiro Yamada aa8a93480e ARM: uniphier: default to environment in eMMC
Of the several boot devices supported, it looks like the eMMC is the
most commonly used.  Enable CONFIG_ENV_IS_IN_MMC by default.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:16 +09:00

286 lines
8.1 KiB
C

/*
* Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* U-Boot - Common settings for UniPhier Family */
#ifndef __CONFIG_UNIPHIER_COMMON_H__
#define __CONFIG_UNIPHIER_COMMON_H__
#define CONFIG_I2C_EEPROM
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#ifdef CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE
#define CONFIG_SYS_NS16550_CLK 12288000
#define CONFIG_SYS_NS16550_REG_SIZE -2
#endif
/* TODO: move to Kconfig and device tree */
#if 0
#define CONFIG_SYS_NS16550_SERIAL
#endif
#define CONFIG_SMC911X
/* dummy: referenced by examples/standalone/smc911x_eeprom.c */
#define CONFIG_SMC911X_BASE 0
#define CONFIG_SMC911X_32_BIT
/*-----------------------------------------------------------------------
* MMU and Cache Setting
*----------------------------------------------------------------------*/
/* Comment out the following to enable L1 cache */
/* #define CONFIG_SYS_ICACHE_OFF */
/* #define CONFIG_SYS_DCACHE_OFF */
#define CONFIG_SYS_CACHELINE_SIZE 32
/* Comment out the following to enable L2 cache */
#define CONFIG_UNIPHIER_L2CACHE_ON
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_MISC_INIT_F
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#define CONFIG_TIMESTAMP
/* FLASH related */
#define CONFIG_MTD_DEVICE
/*
* uncomment the following to disable FLASH related code.
*/
/* #define CONFIG_SYS_NO_FLASH */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_MAX_FLASH_SECT 256
#define CONFIG_SYS_MONITOR_BASE 0
#define CONFIG_SYS_FLASH_BASE 0
/*
* flash_toggle does not work for out supoort card.
* We need to use flash_status_poll.
*/
#define CONFIG_SYS_CFI_FLASH_STATUS_POLL
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
/* serial console configuration */
#define CONFIG_BAUDRATE 115200
#if !defined(CONFIG_SPL_BUILD)
#define CONFIG_USE_ARCH_MEMSET
#define CONFIG_USE_ARCH_MEMCPY
#endif
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* add command line history */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
#define CONFIG_CONS_INDEX 1
/* #define CONFIG_ENV_IS_NOWHERE */
/* #define CONFIG_ENV_IS_IN_NAND */
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_ENV_OFFSET 0x80000
#define CONFIG_ENV_SIZE 0x2000
/* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_SYS_MMC_ENV_PART 1
/* Time clock 1MHz */
#define CONFIG_SYS_TIMER_RATE 1000000
/*
* By default, ARP timeout is 5 sec.
* The first ARP request does not seem to work.
* So we need to retry ARP request anyway.
* We want to shrink the interval until the second ARP request.
*/
#define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_MAX_CHIPS 2
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_NAND_DENALI_ECC_SIZE 1024
#ifdef CONFIG_ARCH_UNIPHIER_PH1_SLD3
#define CONFIG_SYS_NAND_REGS_BASE 0xf8100000
#define CONFIG_SYS_NAND_DATA_BASE 0xf8000000
#else
#define CONFIG_SYS_NAND_REGS_BASE 0x68100000
#define CONFIG_SYS_NAND_DATA_BASE 0x68000000
#endif
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10)
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
/* USB */
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 4
#define CONFIG_CMD_FAT
#define CONFIG_FAT_WRITE
#define CONFIG_DOS_PARTITION
/* SD/MMC */
#define CONFIG_CMD_MMC
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_GENERIC_MMC
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000)
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
/*
* Network Configuration
*/
#define CONFIG_SERVERIP 192.168.11.1
#define CONFIG_IPADDR 192.168.11.10
#define CONFIG_GATEWAYIP 192.168.11.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_LOADADDR 0x84000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING /* add command line history */
#define CONFIG_BOOTCOMMAND "run $bootmode"
#define CONFIG_ROOTPATH "/nfs/root/path"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs $bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
"run __nfsboot"
#ifdef CONFIG_FIT
#define CONFIG_BOOTFILE "fitImage"
#define LINUXBOOT_ENV_SETTINGS \
"fit_addr=0x00100000\0" \
"fit_addr_r=0x84100000\0" \
"fit_size=0x00f00000\0" \
"norboot=setexpr fit_addr $nor_base + $fit_addr &&" \
"bootm $fit_addr\0" \
"nandboot=nand read $fit_addr_r $fit_addr $fit_size &&" \
"bootm $fit_addr_r\0" \
"tftpboot=tftpboot $fit_addr_r $bootfile &&" \
"bootm $fit_addr_r\0" \
"__nfsboot=run tftpboot\0"
#else
#define CONFIG_CMD_BOOTZ
#define CONFIG_BOOTFILE "zImage"
#define LINUXBOOT_ENV_SETTINGS \
"fdt_addr=0x00100000\0" \
"fdt_addr_r=0x84100000\0" \
"fdt_size=0x00008000\0" \
"kernel_addr=0x00200000\0" \
"kernel_addr_r=0x80208000\0" \
"kernel_size=0x00800000\0" \
"ramdisk_addr=0x00a00000\0" \
"ramdisk_addr_r=0x84a00000\0" \
"ramdisk_size=0x00600000\0" \
"ramdisk_file=rootfs.cpio.uboot\0" \
"boot_common=setexpr bootm_low $kernel_addr_r '&' fe000000 &&" \
"bootz $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \
"norboot=setexpr kernel_addr $nor_base + $kernel_addr &&" \
"cp.b $kernel_addr $kernel_addr_r $kernel_size &&" \
"setexpr ramdisk_addr_r $nor_base + $ramdisk_addr &&" \
"setexpr fdt_addr_r $nor_base + $fdt_addr &&" \
"run boot_common\0" \
"nandboot=nand read $kernel_addr_r $kernel_addr $kernel_size &&" \
"nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \
"nand read $fdt_addr_r $fdt_addr $fdt_size &&" \
"run boot_common\0" \
"tftpboot=tftpboot $kernel_addr_r $bootfile &&" \
"tftpboot $ramdisk_addr_r $ramdisk_file &&" \
"tftpboot $fdt_addr_r $fdt_file &&" \
"run boot_common\0" \
"__nfsboot=tftpboot $kernel_addr_r $bootfile &&" \
"tftpboot $fdt_addr_r $fdt_file &&" \
"tftpboot $fdt_addr_r $fdt_file &&" \
"setenv ramdisk_addr_r - &&" \
"run boot_common\0"
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"verify=n\0" \
"nor_base=0x42000000\0" \
"emmcupdate=mmcsetn &&" \
"mmc partconf $mmc_first_dev 0 1 1 &&" \
"mmc erase 0 800 &&" \
"tftpboot u-boot-spl.bin &&" \
"mmc write $loadaddr 0 80 &&" \
"tftpboot u-boot.img &&" \
"mmc write $loadaddr 80 780\0" \
"nandupdate=nand erase 0 0x00100000 &&" \
"tftpboot u-boot-spl.bin &&" \
"nand write $loadaddr 0 0x00010000 &&" \
"tftpboot u-boot.img &&" \
"nand write $loadaddr 0x00010000 0x000f0000\0" \
LINUXBOOT_ENV_SETTINGS
#define CONFIG_SYS_BOOTMAPSZ 0x20000000
/* Open Firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define CONFIG_NR_DRAM_BANKS 2
#if defined(CONFIG_ARCH_UNIPHIER_PH1_SLD3) || \
defined(CONFIG_ARCH_UNIPHIER_PH1_LD4) || \
defined(CONFIG_ARCH_UNIPHIER_PH1_SLD8)
#define CONFIG_SPL_TEXT_BASE 0x00040000
#else
#define CONFIG_SPL_TEXT_BASE 0x00100000
#endif
#define CONFIG_SPL_STACK (0x00100000)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE)
#define CONFIG_PANIC_HANG
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x80
#define CONFIG_SPL_MAX_FOOTPRINT 0x10000
#endif /* __CONFIG_UNIPHIER_COMMON_H__ */