mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-30 06:53:09 +00:00
9caa9de253
Improve documentation. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Link: https://lore.kernel.org/r/20230320114609.930145-3-christianshewitt@gmail.com Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
136 lines
6.7 KiB
ReStructuredText
136 lines
6.7 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
|
|
Amlogic SoC Boot Flow
|
|
=====================
|
|
|
|
Amlogic SoCs follow a pre-defined boot sequence stored in SoC ROM code. The possible boot
|
|
sequences of the different SoC families are:
|
|
|
|
GX* & AXG Family
|
|
----------------
|
|
|
|
+----------+-------------------+---------+---------+---------+---------+
|
|
| | 1 | 2 | 3 | 4 | 5 |
|
|
+==========+===================+=========+=========+=========+=========+
|
|
| S905 | POC=0: SPI NOR | eMMC | NAND | SD | USB |
|
|
| S905D | | | | | |
|
|
| S905L | | | | | |
|
|
| S905W | | | | | |
|
|
| S905X | | | | | |
|
|
| S905Y | | | | | |
|
|
| S912 | | | | | |
|
|
+----------+-------------------+---------+---------+---------+---------+
|
|
| S805X | POC=0: SPI NOR | eMMC | NAND | USB | - |
|
|
| A113D | | | | | |
|
|
| A113X | | | | | |
|
|
+----------+-------------------+---------+---------+---------+---------+
|
|
|
|
POC pin: `NAND_CLE`
|
|
|
|
Some boards provide a button to force USB boot by disabling the eMMC clock signal and
|
|
allowing the eMMC step to be bypassed. Others have removable eMMC modules; removing an
|
|
eMMC module and SD card will allow boot from USB.
|
|
|
|
An exception is the Libre Computer AML-S805X-XX (LaFrite) board which has no SD card
|
|
slot and boots from SPI. Booting a LaFrite board from USB requires either:
|
|
|
|
- Erasing the first sectors of SPI NOR flash
|
|
- Inserting an HDMI boot plug forcing boot over USB
|
|
|
|
The VIM1 and initial VIM2 boards provide a test point on the eMMC signals to block the
|
|
storage from answering, allowing boot to continue with the next boot step.
|
|
|
|
USB boot uses the first USB interface. On some boards this port is only available on a
|
|
USB-A type connector and requires a special Type-A to Type-A cable to communicate with
|
|
the BootROM.
|
|
|
|
G12* & SM1 Family
|
|
-----------------
|
|
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
| POC0 | POC1 | POC2 | 1 | 2 | 3 | 4 |
|
|
+=======+=======+=======+============+============+============+===========+
|
|
| 0 | 0 | 0 | USB | SPI-NOR | NAND/eMMC | SD |
|
|
+-------+-------+-------+------------+------------+-------------+----------+
|
|
| 0 | 0 | 1 | USB | NAND/eMMC | SD | - |
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
| 0 | 1 | 0 | SPI-NOR | NAND/eMMC | SD | USB |
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
| 0 | 1 | 1 | SPI-NAND | NAND/eMMC | USB | - |
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
| 1 | 0 | 0 | USB | SPI-NOR | NAND/eMMC | SD |
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
| 1 | 0 | 1 | USB | NAND/eMMC | SD | - |
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
| 1 | 1 | 0 | SPI-NOR | NAND/eMMC | SD | USB |
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
| 1 | 1 | 1 | NAND/eMMC | SD | USB | - |
|
|
+-------+-------+-------+------------+------------+------------+-----------+
|
|
|
|
The last option (1/1/1) is the normal default seen on production devices:
|
|
|
|
* POC0 pin: `BOOT_4` (0 and all other 1 means SPI NAND boot first)
|
|
* POC1 pin: `BOOT_5` (0 and all other 1 means USB Device boot first
|
|
* POC2 pin: `BOOT_6` (0 and all other 1 means SPI NOR boot first)
|
|
|
|
Most boards provide a button to force USB BOOT which lowers `BOOT_5` to 0. Some boards
|
|
provide a test point on eMMC or SPI NOR clock signals to block storage from answering
|
|
and allowing boot to continue from the next boot step.
|
|
|
|
The Khadas VIM3/3L boards embed a microcontroller which sets POC signals according to
|
|
its configuration or a specific key press sequence to either boot from SPI NOR or eMMC
|
|
then SD card, or boot as a USB device.
|
|
|
|
The Odroid N2/N2+ has a hardware switch to select between SPI NOR or eMMC boot. The
|
|
Odroid HC4 has a button to disable SPI-NOR allowing boot from SD card.
|
|
|
|
Boot Modes
|
|
----------
|
|
|
|
* SD
|
|
|
|
The BootROM fetches the first SD card sectors in one sequence then checks the content of
|
|
the data. It expects to find the FIP binary in sector 1, 512 bytes offset from the start.
|
|
|
|
* eMMC
|
|
|
|
The BootROM fetches the first sectors of the main partition in one sequence then checks
|
|
the content of the data. On GXL and newer boards it expects to find the FIP binary in
|
|
sector 1, 512 bytes offset from the start. If not found it checks the boot0 partition,
|
|
then the boot1 partition. On GXBB it expects to find the FIP binary at an offset that
|
|
conflicts with MBR partition tables, but this has been worked around (thus avoiding the
|
|
need for a partition scheme that relocates the MBR). For a more detailed explanation
|
|
please see: https://github.com/LibreELEC/amlogic-boot-fip/pull/8
|
|
|
|
* SPI-NOR
|
|
|
|
The BootROM fetches the first SPI NOR sectors in one sequence then checks the content of
|
|
the data. It expects to find the FIP binary in sector 1, 512 bytes offset from the start.
|
|
|
|
* NAND & SPI-NAND
|
|
|
|
These modes are rarely used in open platforms and no details are available.
|
|
|
|
* USB
|
|
|
|
The BootROM supports a custom USB protocol and sets the USB Gadget interface to use the
|
|
USB ID 1b8e:c003. The Amlogic `update` utility uses this protocol. It is also supported
|
|
in the Amlogic vendor U-Boot sources.
|
|
|
|
The `pyamlboot` utility https://github.com/superna9999/pyamlboot is open-source and also
|
|
implements the USB protocol. It can load U-Boot into memory to start the SoC without the
|
|
storage being attached, or to recover the device from a failed/incorrect image flash.
|
|
|
|
HDMI Recovery Dongle
|
|
--------------------
|
|
|
|
The BootROM also reads 8 bytes at address I2C 0x52 offset 0xf8 (248) on the HDMI DDC bus
|
|
during startup. The content `boot@USB` forces USB boot. The content `boot@SDC` forces SD
|
|
card boot. The content `boot@SPI` forces SPI-NOT boot. If an SD card or USB device does
|
|
not enumerate the BootROM continues with the normal boot sequence.
|
|
|
|
HDMI boot dongles can be created by connecting a 256bytes EEPROM set to answer on address
|
|
0x52, with `boot@USB` or `boot@SDC` or `boot@SPI` programmed at offset 0xf8 (248).
|
|
|
|
If the SoC is booted with USB Device forced at first step, it will retain the forced boot
|
|
order on warm reboot. Only cold reboot (removing power) will reset the boot order.
|