u-boot/arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

217 lines
6.3 KiB
C

/*
* DDR3 mem setup file for SMDK5250 board based on EXYNOS5
*
* Copyright (C) 2012 Samsung Electronics
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/cpu.h>
#include <asm/arch/dmc.h>
#include "common_setup.h"
#include "exynos5_setup.h"
#include "clock_init.h"
#define RDLVL_COMPLETE_TIMEOUT 10000
static void reset_phy_ctrl(void)
{
struct exynos5_clock *clk =
(struct exynos5_clock *)samsung_get_base_clock();
writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
}
int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
int reset)
{
unsigned int val;
struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
struct exynos5_dmc *dmc;
int i;
phy0_ctrl = (struct exynos5_phy_control *)samsung_get_base_dmc_phy();
phy1_ctrl = (struct exynos5_phy_control *)(samsung_get_base_dmc_phy()
+ DMC_OFFSET);
dmc = (struct exynos5_dmc *)samsung_get_base_dmc_ctrl();
if (reset)
reset_phy_ctrl();
/* Set Impedance Output Driver */
val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
(mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
(mem->impedance << CA_CS_DRVR_DS_OFFSET) |
(mem->impedance << CA_ADR_DRVR_DS_OFFSET);
writel(val, &phy0_ctrl->phy_con39);
writel(val, &phy1_ctrl->phy_con39);
/* Set Read Latency and Burst Length for PHY0 and PHY1 */
val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
(mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
writel(val, &phy0_ctrl->phy_con42);
writel(val, &phy1_ctrl->phy_con42);
/* ZQ Calibration */
if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
/* DQ Signal */
writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
| (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
&dmc->concontrol);
update_reset_dll(dmc, DDR_MODE_DDR3);
/* DQS Signal */
writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
writel(val, &phy0_ctrl->phy_con12);
writel(val, &phy1_ctrl->phy_con12);
/* Start DLL locking */
writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
&phy0_ctrl->phy_con12);
writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
&phy1_ctrl->phy_con12);
update_reset_dll(dmc, DDR_MODE_DDR3);
writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
&dmc->concontrol);
/* Memory Channel Inteleaving Size */
writel(mem->iv_size, &dmc->ivcontrol);
writel(mem->memconfig, &dmc->memconfig0);
writel(mem->memconfig, &dmc->memconfig1);
writel(mem->membaseconfig0, &dmc->membaseconfig0);
writel(mem->membaseconfig1, &dmc->membaseconfig1);
/* Precharge Configuration */
writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
&dmc->prechconfig);
/* Power Down mode Configuration */
writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
&dmc->pwrdnconfig);
/* TimingRow, TimingData, TimingPower and Timingaref
* values as per Memory AC parameters
*/
writel(mem->timing_ref, &dmc->timingref);
writel(mem->timing_row, &dmc->timingrow);
writel(mem->timing_data, &dmc->timingdata);
writel(mem->timing_power, &dmc->timingpower);
/* Send PALL command */
dmc_config_prech(mem, dmc);
/* Send NOP, MRS and ZQINIT commands */
dmc_config_mrs(mem, dmc);
if (mem->gate_leveling_enable) {
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
writel(val, &phy0_ctrl->phy_con0);
writel(val, &phy1_ctrl->phy_con0);
val = PHY_CON2_RESET_VAL;
val |= INIT_DESKEW_EN;
writel(val, &phy0_ctrl->phy_con2);
writel(val, &phy1_ctrl->phy_con2);
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
val |= BYTE_RDLVL_EN;
writel(val, &phy0_ctrl->phy_con0);
writel(val, &phy1_ctrl->phy_con0);
val = (mem->ctrl_start_point <<
PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
writel(val, &phy0_ctrl->phy_con12);
writel(val, &phy1_ctrl->phy_con12);
val = PHY_CON2_RESET_VAL;
val |= INIT_DESKEW_EN;
val |= RDLVL_GATE_EN;
writel(val, &phy0_ctrl->phy_con2);
writel(val, &phy1_ctrl->phy_con2);
val = PHY_CON0_RESET_VAL;
val |= P0_CMD_EN;
val |= BYTE_RDLVL_EN;
val |= CTRL_SHGATE;
writel(val, &phy0_ctrl->phy_con0);
writel(val, &phy1_ctrl->phy_con0);
val = PHY_CON1_RESET_VAL;
val &= ~(CTRL_GATEDURADJ_MASK);
writel(val, &phy0_ctrl->phy_con1);
writel(val, &phy1_ctrl->phy_con1);
writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
i = RDLVL_COMPLETE_TIMEOUT;
while ((readl(&dmc->phystatus) &
(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
/*
* TODO(waihong): Comment on how long this take to
* timeout
*/
sdelay(100);
i--;
}
if (!i)
return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
writel(0, &phy0_ctrl->phy_con14);
writel(0, &phy1_ctrl->phy_con14);
val = (mem->ctrl_start_point <<
PHY_CON12_CTRL_START_POINT_SHIFT) |
(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
writel(val, &phy0_ctrl->phy_con12);
writel(val, &phy1_ctrl->phy_con12);
update_reset_dll(dmc, DDR_MODE_DDR3);
}
/* Send PALL command */
dmc_config_prech(mem, dmc);
writel(mem->memcontrol, &dmc->memcontrol);
/* Set DMC Concontrol and enable auto-refresh counter */
writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
| (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
return 0;
}