u-boot/drivers/usb/host/xhci-omap.c
Felipe Balbi 26707d9e6b usb: host: xhci: make sure to power up PHY
some boards won't work if the PHY isn't explicitly
powered up.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-09 22:11:51 +02:00

159 lines
3.7 KiB
C

/*
* OMAP USB HOST xHCI Controller
*
* (C) Copyright 2013
* Texas Instruments, <www.ti.com>
*
* Author: Dan Murphy <dmurphy@ti.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <usb.h>
#include <asm-generic/errno.h>
#include <asm/omap_common.h>
#include <asm/arch/cpu.h>
#include <asm/arch/sys_proto.h>
#include <linux/compat.h>
#include <linux/usb/dwc3.h>
#include <linux/usb/xhci-omap.h>
#include "xhci.h"
/* Declare global data pointer */
DECLARE_GLOBAL_DATA_PTR;
static struct omap_xhci omap;
inline int __board_usb_init(int index, enum usb_init_type init)
{
return 0;
}
int board_usb_init(int index, enum usb_init_type init)
__attribute__((weak, alias("__board_usb_init")));
static void dwc3_set_mode(struct dwc3 *dwc3_reg, u32 mode)
{
clrsetbits_le32(&dwc3_reg->g_ctl,
DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG),
DWC3_GCTL_PRTCAPDIR(mode));
}
static void dwc3_core_soft_reset(struct dwc3 *dwc3_reg)
{
/* Before Resetting PHY, put Core in Reset */
setbits_le32(&dwc3_reg->g_ctl, DWC3_GCTL_CORESOFTRESET);
omap_reset_usb_phy(dwc3_reg);
/* After PHYs are stable we can take Core out of reset state */
clrbits_le32(&dwc3_reg->g_ctl, DWC3_GCTL_CORESOFTRESET);
}
static int dwc3_core_init(struct dwc3 *dwc3_reg)
{
u32 reg;
u32 revision;
unsigned int dwc3_hwparams1;
revision = readl(&dwc3_reg->g_snpsid);
/* This should read as U3 followed by revision number */
if ((revision & DWC3_GSNPSID_MASK) != 0x55330000) {
puts("this is not a DesignWare USB3 DRD Core\n");
return -1;
}
dwc3_core_soft_reset(dwc3_reg);
dwc3_hwparams1 = readl(&dwc3_reg->g_hwparams1);
reg = readl(&dwc3_reg->g_ctl);
reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
reg &= ~DWC3_GCTL_DISSCRAMBLE;
switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc3_hwparams1)) {
case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
reg &= ~DWC3_GCTL_DSBLCLKGTNG;
break;
default:
debug("No power optimization available\n");
}
/*
* WORKAROUND: DWC3 revisions <1.90a have a bug
* where the device can fail to connect at SuperSpeed
* and falls back to high-speed mode which causes
* the device to enter a Connect/Disconnect loop
*/
if ((revision & DWC3_REVISION_MASK) < 0x190a)
reg |= DWC3_GCTL_U2RSTECN;
writel(reg, &dwc3_reg->g_ctl);
return 0;
}
static int omap_xhci_core_init(struct omap_xhci *omap)
{
int ret = 0;
usb_phy_power(1);
omap_enable_phy(omap);
ret = dwc3_core_init(omap->dwc3_reg);
if (ret) {
debug("%s:failed to initialize core\n", __func__);
return ret;
}
/* We are hard-coding DWC3 core to Host Mode */
dwc3_set_mode(omap->dwc3_reg, DWC3_GCTL_PRTCAP_HOST);
return ret;
}
static void omap_xhci_core_exit(struct omap_xhci *omap)
{
usb_phy_power(0);
}
int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor **hcor)
{
struct omap_xhci *ctx = &omap;
int ret = 0;
ctx->hcd = (struct xhci_hccr *)OMAP_XHCI_BASE;
ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) + DWC3_REG_OFFSET);
ctx->usb3_phy = (struct omap_usb3_phy *)OMAP_OCP1_SCP_BASE;
ctx->otg_wrapper = (struct omap_dwc_wrapper *)OMAP_OTG_WRAPPER_BASE;
ret = board_usb_init(index, USB_INIT_HOST);
if (ret != 0) {
puts("Failed to initialize board for USB\n");
return ret;
}
ret = omap_xhci_core_init(ctx);
if (ret < 0) {
puts("Failed to initialize xhci\n");
return ret;
}
*hccr = (struct xhci_hccr *)(OMAP_XHCI_BASE);
*hcor = (struct xhci_hcor *)((uint32_t) *hccr
+ HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
debug("omap-xhci: init hccr %x and hcor %x hc_length %d\n",
(uint32_t)*hccr, (uint32_t)*hcor,
(uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
return ret;
}
void xhci_hcd_stop(int index)
{
struct omap_xhci *ctx = &omap;
omap_xhci_core_exit(ctx);
}