mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-23 19:43:33 +00:00
e46b72436c
Revamp the documentation for the new features, including a description of the new features and documentation for the trace command. Signed-off-by: Simon Glass <sjg@chromium.org>
503 lines
16 KiB
ReStructuredText
503 lines
16 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
.. Copyright (c) 2013 The Chromium OS Authors.
|
|
|
|
Tracing in U-Boot
|
|
=================
|
|
|
|
U-Boot supports a simple tracing feature which allows a record of execution
|
|
to be collected and sent to a host machine for analysis. At present the
|
|
main use for this is to profile boot time.
|
|
|
|
|
|
Overview
|
|
--------
|
|
|
|
The trace feature uses GCC's instrument-functions feature to trace all
|
|
function entry/exit points. These are then recorded in a memory buffer.
|
|
The memory buffer can be saved to the host over a network link using
|
|
tftpput or by writing to an attached storage device such as MMC.
|
|
|
|
On the host, the file is first converted with a tool called 'proftool',
|
|
which extracts useful information from it. The resulting trace output
|
|
resembles that emitted by Linux's ftrace feature, so can be visually
|
|
displayed by kernelshark (see kernelshark_) and used with
|
|
'trace-cmd report' (see trace_cmd_).
|
|
|
|
It is also possible to produce a flame graph for use with flamegraph.pl
|
|
(see flamegraph_pl_).
|
|
|
|
|
|
Quick-start using Sandbox
|
|
-------------------------
|
|
|
|
Sandbox is a build of U-Boot that can run under Linux so it is a convenient
|
|
way of trying out tracing before you use it on your actual board. To do
|
|
this, follow these steps:
|
|
|
|
Add the following to `config/sandbox_defconfig`:
|
|
|
|
.. code-block:: c
|
|
|
|
CONFIG_TRACE=y
|
|
|
|
Build sandbox U-Boot with tracing enabled:
|
|
|
|
.. code-block:: console
|
|
|
|
$ make FTRACE=1 O=sandbox sandbox_config
|
|
$ make FTRACE=1 O=sandbox
|
|
|
|
Run sandbox, wait for a bit of trace information to appear, and then capture
|
|
a trace:
|
|
|
|
.. code-block:: console
|
|
|
|
$ ./sandbox/u-boot
|
|
|
|
U-Boot 2013.04-rc2-00100-ga72fcef (Apr 17 2013 - 19:25:24)
|
|
|
|
DRAM: 128 MiB
|
|
trace: enabled
|
|
Using default environment
|
|
|
|
In: serial
|
|
Out: serial
|
|
Err: serial
|
|
=>trace stats
|
|
671,406 function sites
|
|
69,712 function calls
|
|
0 untracked function calls
|
|
73,373 traced function calls
|
|
16 maximum observed call depth
|
|
15 call depth limit
|
|
66,491 calls not traced due to depth
|
|
=>trace stats
|
|
671,406 function sites
|
|
1,279,450 function calls
|
|
0 untracked function calls
|
|
950,490 traced function calls (333217 dropped due to overflow)
|
|
16 maximum observed call depth
|
|
15 call depth limit
|
|
1,275,767 calls not traced due to depth
|
|
=>trace calls 1000000 e00000
|
|
Call list dumped to 00000000, size 0xae0a40
|
|
=>print
|
|
baudrate=115200
|
|
profbase=0
|
|
profoffset=ae0a40
|
|
profsize=e00000
|
|
stderr=serial
|
|
stdin=serial
|
|
stdout=serial
|
|
|
|
Environment size: 117/8188 bytes
|
|
=>host save hostfs - 1000000 trace ${profoffset}
|
|
11405888 bytes written in 10 ms (1.1 GiB/s)
|
|
=>reset
|
|
|
|
|
|
Then run proftool to convert the trace information to ftrace format
|
|
|
|
.. code-block:: console
|
|
|
|
$ ./sandbox/tools/proftool -m sandbox/System.map -t trace dump-ftrace >trace.dat
|
|
|
|
Finally run kernelshark to display it (note it only works with `.dat` files!):
|
|
|
|
.. code-block:: console
|
|
|
|
$ kernelshark trace.dat
|
|
|
|
Using this tool you can view the trace records and see the timestamp for each
|
|
function.
|
|
|
|
.. image:: pics/kernelshark.png
|
|
:width: 800
|
|
:alt: Kernelshark showing function-trace records
|
|
|
|
|
|
To see the records on the console, use trace-cmd:
|
|
|
|
.. code-block:: console
|
|
|
|
$ trace-cmd report trace.dat | less
|
|
cpus=1
|
|
u-boot-1 [000] 3.116364: function: initf_malloc
|
|
u-boot-1 [000] 3.116375: function: initf_malloc
|
|
u-boot-1 [000] 3.116386: function: initf_bootstage
|
|
u-boot-1 [000] 3.116396: function: bootstage_init
|
|
u-boot-1 [000] 3.116408: function: malloc
|
|
u-boot-1 [000] 3.116418: function: malloc_simple
|
|
u-boot-1 [000] 3.116429: function: alloc_simple
|
|
u-boot-1 [000] 3.116441: function: alloc_simple
|
|
u-boot-1 [000] 3.116449: function: malloc_simple
|
|
u-boot-1 [000] 3.116457: function: malloc
|
|
|
|
Note that `pytimechart` is obsolete so cannot be used anymore.
|
|
|
|
There is a -f option available to select a function graph:
|
|
|
|
.. code-block:: console
|
|
|
|
$ ./sandbox/tools/proftool -m sandbox/System.map -t trace -f funcgraph dump-ftrace >trace.dat
|
|
|
|
Again, you can use kernelshark or trace-cmd to look at the output. In this case
|
|
you will see the time taken by each function shown against its exit record.
|
|
|
|
.. image:: pics/kernelshark_fg.png
|
|
:width: 800
|
|
:alt: Kernelshark showing function-graph records
|
|
|
|
.. code-block:: console
|
|
|
|
$ trace-cmd report trace.dat | less
|
|
cpus=1
|
|
u-boot-1 [000] 3.116364: funcgraph_entry: 0.011 us | initf_malloc();
|
|
u-boot-1 [000] 3.116386: funcgraph_entry: | initf_bootstage() {
|
|
u-boot-1 [000] 3.116396: funcgraph_entry: | bootstage_init() {
|
|
u-boot-1 [000] 3.116408: funcgraph_entry: | malloc() {
|
|
u-boot-1 [000] 3.116418: funcgraph_entry: | malloc_simple() {
|
|
u-boot-1 [000] 3.116429: funcgraph_entry: 0.012 us | alloc_simple();
|
|
u-boot-1 [000] 3.116449: funcgraph_exit: 0.031 us | }
|
|
u-boot-1 [000] 3.116457: funcgraph_exit: 0.049 us | }
|
|
u-boot-1 [000] 3.116466: funcgraph_entry: 0.063 us | memset();
|
|
u-boot-1 [000] 3.116539: funcgraph_exit: 0.143 us | }
|
|
|
|
Flame graph
|
|
-----------
|
|
|
|
Some simple flame graph options are available as well, using the dump-flamegraph
|
|
command:
|
|
|
|
.. code-block:: console
|
|
|
|
$ ./sandbox/tools/proftool -m sandbox/System.map -t trace dump-flamegraph >trace.fg
|
|
$ flamegraph.pl trace.fg >trace.svg
|
|
|
|
You can load the .svg file into a viewer. If you use Chrome (and some other
|
|
programs) you can click around and zoom in and out.
|
|
|
|
.. image:: pics/flamegraph.png
|
|
:width: 800
|
|
:alt: Chrome showing the flamegraph.pl output
|
|
|
|
.. image:: pics/flamegraph_zoom.png
|
|
:width: 800
|
|
:alt: Chrome showing zooming into the flamegraph.pl output
|
|
|
|
|
|
A timing variant is also available, which gives an idea of how much time is
|
|
spend in each call stack:
|
|
|
|
.. code-block:: console
|
|
|
|
$ ./sandbox/tools/proftool -m sandbox/System.map -t trace dump-flamegraph -f timing >trace.fg
|
|
$ flamegraph.pl trace.fg >trace.svg
|
|
|
|
Note that trace collection does slow down execution so the timings will be
|
|
inflated. They should be used to guide optimisation. For accurate boot timings,
|
|
use bootstage.
|
|
|
|
.. image:: pics/flamegraph_timing.png
|
|
:width: 800
|
|
:alt: Chrome showing flamegraph.pl output with timing
|
|
|
|
CONFIG Options
|
|
--------------
|
|
|
|
CONFIG_TRACE
|
|
Enables the trace feature in U-Boot.
|
|
|
|
CONFIG_CMD_TRACE
|
|
Enables the trace command.
|
|
|
|
CONFIG_TRACE_BUFFER_SIZE
|
|
Size of trace buffer to allocate for U-Boot. This buffer is
|
|
used after relocation, as a place to put function tracing
|
|
information. The address of the buffer is determined by
|
|
the relocation code.
|
|
|
|
CONFIG_TRACE_EARLY
|
|
Define this to start tracing early, before relocation.
|
|
|
|
CONFIG_TRACE_EARLY_SIZE
|
|
Size of 'early' trace buffer. Before U-Boot has relocated
|
|
it doesn't have a proper trace buffer. On many boards
|
|
you can define an area of memory to use for the trace
|
|
buffer until the 'real' trace buffer is available after
|
|
relocation. The contents of this buffer are then copied to
|
|
the real buffer.
|
|
|
|
CONFIG_TRACE_EARLY_ADDR
|
|
Address of early trace buffer
|
|
|
|
CONFIG_TRACE_CALL_DEPTH_LIMIT
|
|
Sets the limit on trace call-depth. For a broad view, 10 is typically
|
|
sufficient. Setting this too large creates enormous traces and distorts
|
|
the overall timing considerable.
|
|
|
|
|
|
Building U-Boot with Tracing Enabled
|
|
------------------------------------
|
|
|
|
Pass 'FTRACE=1' to the U-Boot Makefile to actually instrument the code.
|
|
This is kept as a separate option so that it is easy to enable/disable
|
|
instrumenting from the command line instead of having to change board
|
|
config files.
|
|
|
|
|
|
Board requirements
|
|
------------------
|
|
|
|
Trace data collection relies on a microsecond timer, accessed through
|
|
`timer_get_us()`. So the first thing you should do is make sure that
|
|
this produces sensible results for your board. Suitable sources for
|
|
this timer include high resolution timers, PWMs or profile timers if
|
|
available. Most modern SOCs have a suitable timer for this.
|
|
|
|
See `add_ftrace()` for where `timer_get_us()` is called. The `notrace`
|
|
attribute must be used on each function called by `timer_get_us()` since
|
|
recursive calls to `add_ftrace()` will cause a fault::
|
|
|
|
trace: recursion detected, disabling
|
|
|
|
You cannot use driver model to obtain the microsecond timer, since tracing
|
|
may be enabled before driver model is set up. Instead, provide a low-level
|
|
function which accesses the timer, setting it up if needed.
|
|
|
|
|
|
Collecting Trace Data
|
|
---------------------
|
|
|
|
When you run U-Boot on your board it will collect trace data up to the
|
|
limit of the trace buffer size you have specified. Once that is exhausted
|
|
no more data will be collected.
|
|
|
|
Collecting trace data affects execution time and performance. You
|
|
will notice this particularly with trivial functions - the overhead of
|
|
recording their execution may even exceed their normal execution time.
|
|
In practice this doesn't matter much so long as you are aware of the
|
|
effect. Once you have done your optimizations, turn off tracing before
|
|
doing end-to-end timing using bootstage.
|
|
|
|
The best time to start tracing is right at the beginning of U-Boot. The
|
|
best time to stop tracing is right at the end. In practice it is hard
|
|
to achieve these ideals.
|
|
|
|
This implementation enables tracing early in `board_init_r()`, or
|
|
`board_init_f()` when `TRACE_EARLY` is enabled. This means
|
|
that it captures most of the board init process, missing only the
|
|
early architecture-specific init. However, it also misses the entire
|
|
SPL stage if there is one. At present tracing is not supported in SPL.
|
|
|
|
U-Boot typically ends with a 'bootm' command which loads and runs an
|
|
OS. There is useful trace data in the execution of that bootm
|
|
command. Therefore this implementation provides a way to collect trace
|
|
data after bootm has finished processing, but just before it jumps to
|
|
the OS. In practical terms, U-Boot runs the 'fakegocmd' environment
|
|
variable at this point. This variable should have a short script which
|
|
collects the trace data and writes it somewhere.
|
|
|
|
Controlling the trace
|
|
---------------------
|
|
|
|
U-Boot provides a command-line interface to the trace system for controlling
|
|
tracing and accessing the trace data. See :doc:`../usage/cmd/trace`.
|
|
|
|
|
|
Environment Variables
|
|
---------------------
|
|
|
|
The following are used:
|
|
|
|
profbase
|
|
Base address of trace output buffer
|
|
|
|
profoffset
|
|
Offset of first unwritten byte in trace output buffer
|
|
|
|
profsize
|
|
Size of trace output buffer
|
|
|
|
All of these are set by the 'trace calls' command.
|
|
|
|
These variables keep track of the amount of data written to the trace
|
|
output buffer by the 'trace' command. The trace commands which write data
|
|
to the output buffer can use these to specify the buffer to write to, and
|
|
update profoffset each time. This allows successive commands to append data
|
|
to the same buffer, for example::
|
|
|
|
=> trace funclist 10000 e00000
|
|
=> trace calls
|
|
|
|
(the latter command appends more data to the buffer).
|
|
|
|
|
|
fakegocmd
|
|
Specifies commands to run just before booting the OS. This
|
|
is a useful time to write the trace data to the host for
|
|
processing.
|
|
|
|
|
|
Writing Out Trace Data
|
|
----------------------
|
|
|
|
Once the trace data is in an output buffer in memory there are various ways
|
|
to transmit it to the host. Notably you can use tftput to send the data
|
|
over a network link::
|
|
|
|
fakegocmd=trace pause; usb start; set autoload n; bootp;
|
|
trace calls 10000000 1000000;
|
|
tftpput ${profbase} ${profoffset} 192.168.1.4:/tftpboot/calls
|
|
|
|
This starts up USB (to talk to an attached USB Ethernet dongle), writes
|
|
a trace log to address 10000000 and sends it to a host machine using
|
|
TFTP. After this, U-Boot will boot the OS normally, albeit a little
|
|
later.
|
|
|
|
For a filesystem you may do something like::
|
|
|
|
trace calls 10000000 1000000;
|
|
save mmc 1:1 10000000 /trace ${profoffset}
|
|
|
|
The trace buffer format is internal to the trace system. It consists of a
|
|
header, a call count for each function site, followed by a list of trace
|
|
records, once for each function call.
|
|
|
|
|
|
Converting Trace Output Data (proftool)
|
|
---------------------------------------
|
|
|
|
The trace output data is kept in a binary format which is not documented
|
|
here. See the `trace.h` header file if you are interested. To convert it into
|
|
something useful, you can use proftool.
|
|
|
|
This tool must be given the U-Boot map file and the trace data received
|
|
from running that U-Boot. It produces a binary output file.
|
|
|
|
It is also possible to provide a configuration file to indicate which functions
|
|
should be included or dropped during conversion. This file consists of lines
|
|
like::
|
|
|
|
include-func <regex>
|
|
exclude-func <regex>
|
|
|
|
where <regex> is a regular expression matched against function names. It
|
|
allows some functions to be dropped from the trace when producing ftrace
|
|
records.
|
|
|
|
Options:
|
|
|
|
-c <config_file>
|
|
Specify the optional configuration file, to control which functions are
|
|
included in the output.
|
|
|
|
-f <format>
|
|
Specifies the format to use (see below)
|
|
|
|
-m <map_file>
|
|
Specify U-Boot map file (`System.map`)
|
|
|
|
-o <output file>
|
|
Specify the output filename
|
|
|
|
-t <trace_file>
|
|
Specify trace file, the data saved from U-Boot
|
|
|
|
-v <0-4>
|
|
Specify the verbosity, where 0 is the minimum and 4 is for debugging.
|
|
|
|
Commands:
|
|
|
|
dump-ftrace:
|
|
Write a binary dump of the file in Linux ftrace format. Two options are
|
|
available:
|
|
|
|
function
|
|
write function-call records (caller/callee)
|
|
|
|
funcgraph
|
|
write function entry/exit records (graph)
|
|
|
|
This format can be used with kernelshark_ and trace_cmd_.
|
|
|
|
dump-flamegraph
|
|
Write a list of stack records useful for producing a flame graph. Two
|
|
options are available:
|
|
|
|
calls
|
|
create a flamegraph of stack frames
|
|
|
|
timing
|
|
create a flamegraph of microseconds for each stack frame
|
|
|
|
This format can be used with flamegraph_pl_.
|
|
|
|
Viewing the Trace Data
|
|
----------------------
|
|
|
|
You can use kernelshark_ for a GUI, but note that version 2.0.x was broken. If
|
|
you have that version you could try building it from source.
|
|
|
|
The file must have a .dat extension or it is ignored. The program has terse
|
|
user interface but is very convenient for viewing U-Boot profile information.
|
|
|
|
Also available is trace_cmd_ which provides a command-line interface.
|
|
|
|
Workflow Suggestions
|
|
--------------------
|
|
|
|
The following suggestions may be helpful if you are trying to reduce boot
|
|
time:
|
|
|
|
1. Enable CONFIG_BOOTSTAGE and CONFIG_BOOTSTAGE_REPORT. This should get
|
|
you are helpful overall snapshot of the boot time.
|
|
|
|
2. Build U-Boot with tracing and run it. Note the difference in boot time
|
|
(it is common for tracing to add 10% to the time)
|
|
|
|
3. Collect the trace information as described above. Use this to find where
|
|
all the time is being spent.
|
|
|
|
4. Take a look at that code and see if you can optimize it. Perhaps it is
|
|
possible to speed up the initialization of a device, or remove an unused
|
|
feature.
|
|
|
|
5. Rebuild, run and collect again. Compare your results.
|
|
|
|
6. Keep going until you run out of steam, or your boot is fast enough.
|
|
|
|
|
|
Configuring Trace
|
|
-----------------
|
|
|
|
There are a few parameters in the code that you may want to consider.
|
|
There is a function call depth limit (set to 15 by default). When the
|
|
stack depth goes above this then no tracing information is recorded.
|
|
The maximum depth reached is recorded and displayed by the 'trace stats'
|
|
command. While it might be tempting to set the depth limit quite high, this
|
|
can dramatically increase the size of the trace output as well as the execution
|
|
time.
|
|
|
|
|
|
Future Work
|
|
-----------
|
|
|
|
Tracing could be a little tidier in some areas, for example providing
|
|
run-time configuration options for trace.
|
|
|
|
Some other features that might be useful:
|
|
|
|
- Trace filter to select which functions are recorded
|
|
- Sample-based profiling using a timer interrupt
|
|
- Better control over trace depth
|
|
- Compression of trace information
|
|
|
|
|
|
.. sectionauthor:: Simon Glass <sjg@chromium.org>
|
|
.. April 2013
|
|
.. Updated January 2023
|
|
|
|
.. _kernelshark: https://kernelshark.org/
|
|
.. _trace_cmd: https://www.trace-cmd.org/
|
|
.. _flamegraph_pl: https://github.com/brendangregg/FlameGraph/blob/master/flamegraph.pl
|