mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-05 12:45:42 +00:00
74e7997c70
Add an help about the USBNET_DEVADDR Kconfig option to make it clearer what it's about. Acked-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
131 lines
4.2 KiB
Text
131 lines
4.2 KiB
Text
#
|
|
# USB Gadget support on a system involves
|
|
# (a) a peripheral controller, and
|
|
# (b) the gadget driver using it.
|
|
#
|
|
# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
|
|
#
|
|
# - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
|
|
# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
|
|
# - Some systems have both kinds of controllers.
|
|
#
|
|
# With help from a special transceiver and a "Mini-AB" jack, systems with
|
|
# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
|
|
#
|
|
|
|
menuconfig USB_GADGET
|
|
bool "USB Gadget Support"
|
|
help
|
|
USB is a master/slave protocol, organized with one master
|
|
host (such as a PC) controlling up to 127 peripheral devices.
|
|
The USB hardware is asymmetric, which makes it easier to set up:
|
|
you can't connect a "to-the-host" connector to a peripheral.
|
|
|
|
U-Boot can run in the host, or in the peripheral. In both cases
|
|
you need a low level bus controller driver, and some software
|
|
talking to it. Peripheral controllers are often discrete silicon,
|
|
or are integrated with the CPU in a microcontroller. The more
|
|
familiar host side controllers have names like "EHCI", "OHCI",
|
|
or "UHCI", and are usually integrated into southbridges on PC
|
|
motherboards.
|
|
|
|
Enable this configuration option if you want to run U-Boot inside
|
|
a USB peripheral device. Configure one hardware driver for your
|
|
peripheral/device side bus controller, and a "gadget driver" for
|
|
your peripheral protocol.
|
|
|
|
if USB_GADGET
|
|
|
|
config USB_GADGET_ATMEL_USBA
|
|
bool "Atmel USBA"
|
|
select USB_GADGET_DUALSPEED
|
|
help
|
|
USBA is the integrated high-speed USB Device controller on
|
|
the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel.
|
|
|
|
config USB_GADGET_BCM_UDC_OTG_PHY
|
|
bool "Broadcom UDC OTG PHY"
|
|
help
|
|
Enable the Broadcom UDC OTG physical device interface.
|
|
|
|
config USB_GADGET_DWC2_OTG
|
|
bool "DesignWare USB2.0 HS OTG controller (gadget mode)"
|
|
select USB_GADGET_DUALSPEED
|
|
help
|
|
The Designware USB2.0 high-speed gadget controller
|
|
integrated into many SoCs. Select this option if you want the
|
|
driver to operate in Peripheral mode. This option requires
|
|
USB_GADGET to be enabled.
|
|
|
|
if USB_GADGET_DWC2_OTG
|
|
|
|
config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
|
|
bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width"
|
|
help
|
|
Set the Designware USB2.0 high-speed OTG controller
|
|
PHY interface width to 8 bits, rather than the default (16 bits).
|
|
|
|
endif # USB_GADGET_DWC2_OTG
|
|
|
|
config CI_UDC
|
|
bool "ChipIdea device controller"
|
|
select USB_GADGET_DUALSPEED
|
|
help
|
|
Say Y here to enable device controller functionality of the
|
|
ChipIdea driver.
|
|
|
|
config USB_GADGET_VBUS_DRAW
|
|
int "Maximum VBUS Power usage (2-500 mA)"
|
|
range 2 500
|
|
default 2
|
|
help
|
|
Some devices need to draw power from USB when they are
|
|
configured, perhaps to operate circuitry or to recharge
|
|
batteries. This is in addition to any local power supply,
|
|
such as an AC adapter or batteries.
|
|
|
|
Enter the maximum power your device draws through USB, in
|
|
milliAmperes. The permitted range of values is 2 - 500 mA;
|
|
0 mA would be legal, but can make some hosts misbehave.
|
|
|
|
This value will be used except for system-specific gadget
|
|
drivers that have more specific information.
|
|
|
|
# Selected by UDC drivers that support high-speed operation.
|
|
config USB_GADGET_DUALSPEED
|
|
bool
|
|
|
|
config USB_GADGET_DOWNLOAD
|
|
bool "Enable USB download gadget"
|
|
help
|
|
Composite USB download gadget support (g_dnl) for download functions.
|
|
This code works on top of composite gadget.
|
|
|
|
if USB_GADGET_DOWNLOAD
|
|
|
|
config USB_FUNCTION_SDP
|
|
bool "Enable USB SDP (Serial Download Protocol)"
|
|
help
|
|
Enable Serial Download Protocol (SDP) device support in U-Boot. This
|
|
allows to download images into memory and execute (jump to) them
|
|
using the same protocol as implemented by the i.MX family's boot ROM.
|
|
|
|
config G_DNL_MANUFACTURER
|
|
string "Vendor name of USB device"
|
|
|
|
config G_DNL_VENDOR_NUM
|
|
hex "Vendor ID of USB device"
|
|
|
|
config G_DNL_PRODUCT_NUM
|
|
hex "Product ID of USB device"
|
|
|
|
endif # USB_GADGET_DOWNLOAD
|
|
|
|
config USBNET_DEVADDR
|
|
string "USB Gadget Ethernet device mac address"
|
|
default "de:ad:be:ef:00:01"
|
|
help
|
|
Ethernet MAC address of the device-side (ie. local board's) MAC
|
|
address of the usb_ether interface
|
|
|
|
endif # USB_GADGET
|