mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-12 06:12:58 +00:00
130b53ec79
Add support for "marvell,reset-gpio" property to mvebu DW PCIe driver. This option is valid when CONFIG_DM_GPIO=y Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986 Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com> Cc: Stefan Roese <sr@denx.de> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Neta Zur Hershkovits <neta@marvell.com> Cc: Igal Liberman <igall@marvell.com> Cc: Haim Boot <hayim@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
49 lines
1.8 KiB
Text
49 lines
1.8 KiB
Text
Armada-8K PCIe DT details:
|
|
==========================
|
|
|
|
Armada-8k uses synopsis designware PCIe controller.
|
|
|
|
Required properties:
|
|
- compatible : should be "marvell,armada8k-pcie", "snps,dw-pcie".
|
|
- reg: base addresses and lengths of the pcie control and global control registers.
|
|
"ctrl" registers points to the global control registers, while the "config" space
|
|
points to the pcie configuration registers as mentioned in dw-pcie dt bindings in the link below.
|
|
- interrupt-map-mask and interrupt-map, standard PCI properties to
|
|
define the mapping of the PCIe interface to interrupt numbers.
|
|
- All other definitions as per generic PCI bindings
|
|
See Linux kernel documentation:
|
|
"Documentation/devicetree/bindings/pci/designware-pcie.txt"
|
|
|
|
Optional properties:
|
|
PHY support is still not supported for armada-8k, once it will, the following parameters can be used:
|
|
- phys : phandle to phy node associated with pcie controller.
|
|
- phy-names : must be "pcie-phy"
|
|
- marvell,reset-gpio : specifies a gpio that needs to be activated for plug-in
|
|
card reset signal release.
|
|
Example:
|
|
|
|
cpm_pcie0: pcie@f2600000 {
|
|
compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
|
|
reg = <0 0xf2600000 0 0x10000>,
|
|
<0 0xf6f00000 0 0x80000>;
|
|
reg-names = "ctrl", "config";
|
|
#address-cells = <3>;
|
|
#size-cells = <2>;
|
|
#interrupt-cells = <1>;
|
|
device_type = "pci";
|
|
dma-coherent;
|
|
|
|
bus-range = <0 0xff>;
|
|
ranges =
|
|
/* downstream I/O */
|
|
<0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000
|
|
/* non-prefetchable memory */
|
|
0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>;
|
|
interrupt-map-mask = <0 0 0 0>;
|
|
interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
|
|
num-lanes = <1>;
|
|
clocks = <&cpm_syscon0 1 13>;
|
|
marvell,reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_HIGH>;
|
|
status = "disabled";
|
|
};
|