u-boot/board/freescale/c29xpcie
Simon Glass 723806cc5b env: Rename some other getenv()-related functions
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:

   getenv_vlan()
   getenv_bootm_size()
   getenv_bootm_low()
   getenv_bootm_mapsize()
   env_get_default()

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:31:11 -04:00
..
c29xpcie.c env: Rename some other getenv()-related functions 2017-08-16 08:31:11 -04:00
cpld.c powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL 2014-01-21 13:42:40 -08:00
cpld.h powerpc/mpc85xx: Cleanup license header in source files 2013-08-12 15:04:24 -07:00
ddr.c powerpc/c29xpcie: Getting DDR SPD image from 16-bit sub-address EEPROM 2013-12-04 14:54:32 -08:00
Kconfig NXP: Introduce board/freescale/common/Kconfig and migrate CHAIN_OF_TRUST 2017-01-24 10:33:59 -05:00
law.c boards/c29xpcie: Update TLB and LAW size for IFC NAND, CPLD 2013-10-16 16:15:17 -07:00
MAINTAINERS powerpc/c29xpcie: Add secure boot support 2015-01-16 09:27:06 -08:00
Makefile freescale: Tweak various Makefiles to remove redundancy, fix aesthetics 2016-06-03 22:14:27 -07:00
README Use correct spelling of "U-Boot" 2016-02-06 12:00:59 +01:00
spl.c env: Add an enum for environment state 2017-08-15 08:18:51 -04:00
spl_minimal.c powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL 2014-01-21 13:42:40 -08:00
tlb.c powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL 2014-01-21 13:42:40 -08:00

Overview
=========
C29XPCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module.
It includes C293PCIE board, C293PCIE board and C291PCIE board.
The Freescale C29x family is a high performance crypto co-processor.
It combines a single e500v2 core with necessary SEC engines.
(maximum core frequency 1000/1200 MHz).

The C29xPCIE board features are as follows:
Memory subsystem:
	- 512Mbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus)
	- 64 Mbyte NOR flash single-chip memory
	- 4 Gbyte NAND flash memory
	- 1 Mbit AT24C1024 I2C EEPROM
	- 16 Mbyte SPI memory

Interfaces:
	- 10/100/1000 BaseT Ethernet ports:
		- eTSEC1, RGMII: one 10/100/1000 port
		- eTSEC2, RGMII: one 10/100/1000 port
	- DUART interface:
		- DUART interface: supports two UARTs up to 115200 bps for
		   console display

Board connectors:
	- Mini-ITX power supply connector
	- JTAG/COP for debugging

Physical Memory Map on C29xPCIE
===============================
Address Start   Address End   Memory type
0x0_0000_0000 - 0x0_1fff_ffff   512MB DDR
0xc_0000_0000 - 0xc_8fff_ffff   256MB PCIE memory
0xf_ec00_0000 - 0xf_efff_ffff   64MB NOR flash
0xf_ffb0_0000 - 0xf_ffb7_ffff   512KB SRAM
0xf_ffc0_0000 - 0xf_ffc0_ffff   64KB PCIE IO
0xf_ffdf_0000 - 0xf_ffdf_0fff   4KB CPLD
0xf_ffe0_0000 - 0xf_ffef_ffff   1MB CCSR

Serial Port Configuration on C29xPCIE
=====================================
Configure the serial port of the attached computer with the following values:
	-Data rate: 115200 bps
	-Number of data bits: 8
	-Parity: None
	-Number of Stop bits: 1
	-Flow Control: Hardware/None

Settings of DIP-switch
======================
  SW5[1:4]= 1111 and SW5[6]=0 for boot from 16bit NOR flash
  SW5[1:4]= 0110 and SW5[6]=0 for boot from SPI flash
Note: 1 stands for 'off', 0 stands for 'on'

Build and program U-Boot to NOR flash
==================================
1. Build u-boot.bin image example:
	export ARCH=powerpc
	export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
	make C293PCIE

2. Program u-boot.bin into NOR flash
	=> tftp $loadaddr $uboot
	=> protect off eff40000 +$filesize
	=> erase eff40000 +$filesize
	=> cp.b $loadaddr eff40000 $filesize

3. Check SW5[1:4]= 1111 and SW5[6]=0, then power on.

Alternate NOR bank
==================
There are four banks in C29XPCIE board, example to change bank booting:
1. Program u-boot.bin into alternate NOR bank
	=> tftp $loadaddr $uboot
	=> protect off e9f40000 +$filesize
	=> erase e9f40000 +$filesize
	=> cp.b $loadaddr e9f40000 $filesize

2. Switch to alternate NOR bank
	=> cpld_cmd reset altbank [bank]
	- [bank] bank value select 1-4
	- bank 1 on the flash 0x0000000~0x0ffffff
	- bank 2 on the flash 0x1000000~0x1ffffff
	- bank 3 on the flash 0x2000000~0x2ffffff
	- bank 4 on the flash 0x3000000~0x3ffffff
	or set SW5[7]= ON/OFF and SW5[7]= ON/OFF, then power on again.

Build and program U-Boot to SPI flash
==================================
1. Build u-boot-spi.bin image
	make C29xPCIE_SPIFLASH_config; make
	Need the boot_format tool to generate u-boot-spi.bin from the u-boot.bin.

2. Program u-boot-spi.bin into SPI flash
	=> tftp $loadaddr $uboot-spi
	=> sf erase 0 100000
	=> sf write $loadaddr 0 $filesize

3. Check SW5[1:4]= 0110 and SW5[6]=0, then power on.