mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 16:39:35 +00:00
702de89cc6
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
88 lines
3 KiB
C
88 lines
3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2012
|
|
* Linaro
|
|
* Linus Walleij <linus.walleij@linaro.org>
|
|
* Common ARM Integrator configuration settings
|
|
*/
|
|
|
|
#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */
|
|
|
|
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
|
|
/*
|
|
* There are various dependencies on the core module (CM) fitted
|
|
* Users should refer to their CM user guide
|
|
*/
|
|
#include "armcoremodule.h"
|
|
|
|
/*
|
|
* Initialize and remap the core module, use SPD to detect memory size
|
|
* If CONFIG_SKIP_LOWLEVEL_INIT is not defined &
|
|
* the core module has a CM_INIT register
|
|
* then the U-Boot initialisation code will
|
|
* e.g. ARM Boot Monitor or pre-loader is repeated once
|
|
* (to re-initialise any existing CM_INIT settings to safe values).
|
|
*
|
|
* This is usually not the desired behaviour since the platform
|
|
* will either reboot into the ARM monitor (or pre-loader)
|
|
* or continuously cycle thru it without U-Boot running,
|
|
* depending upon the setting of Integrator/CP switch S2-4.
|
|
*
|
|
* However it may be needed if Integrator/CP switch S2-1
|
|
* is set OFF to boot direct into U-Boot.
|
|
* In that case comment out the line below.
|
|
*/
|
|
#define CONFIG_CM_INIT
|
|
#define CONFIG_CM_REMAP
|
|
#define CONFIG_CM_SPD_DETECT
|
|
|
|
/*
|
|
* The ARM boot monitor initializes the board.
|
|
* However, the default U-Boot code also performs the initialization.
|
|
* If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT
|
|
* - see documentation supplied with board for details of how to choose the
|
|
* image to run at reset/power up
|
|
* e.g. whether the ARM Boot Monitor runs before U-Boot
|
|
*/
|
|
/* #define CONFIG_SKIP_LOWLEVEL_INIT */
|
|
|
|
/*
|
|
* The ARM boot monitor does not relocate U-Boot.
|
|
* However, the default U-Boot code performs the relocation check,
|
|
* and may relocate the code if the memory map is changed.
|
|
* If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT
|
|
*/
|
|
/* #define SKIP_CONFIG_RELOCATE_UBOOT */
|
|
|
|
/*
|
|
* Physical Memory Map
|
|
*/
|
|
#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
|
|
#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*
|
|
* FLASH and environment organization
|
|
* Top varies according to amount fitted
|
|
* Reserve top 4 blocks of flash
|
|
* - ARM Boot Monitor
|
|
* - Unused
|
|
* - SIB block
|
|
* - U-Boot environment
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0x24000000
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
|
|
|
/* Timeout values in ticks */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Erase Timeout */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Write Timeout */
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */
|