mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-06 21:24:29 +00:00
306881a0bf
This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini <trini@konsulko.com>
122 lines
3 KiB
C
122 lines
3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* siemens rut
|
|
* (C) Copyright 2013 Siemens Schweiz AG
|
|
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
|
|
*
|
|
* Based on:
|
|
* U-Boot file:/include/configs/am335x_evm.h
|
|
*
|
|
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
|
|
*/
|
|
|
|
#ifndef __CONFIG_RUT_H
|
|
#define __CONFIG_RUT_H
|
|
|
|
#define CONFIG_SIEMENS_MACH_TYPE MACH_TYPE_RUT
|
|
|
|
#include "siemens-am33x-common.h"
|
|
|
|
#define RUT_IOCTRL_VAL 0x18b
|
|
#define DDR_PLL_FREQ 303
|
|
|
|
/* Physical Memory Map */
|
|
#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MiB */
|
|
|
|
/* I2C Configuration */
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
|
|
|
|
#define CONFIG_FACTORYSET
|
|
|
|
/* Watchdog */
|
|
#define WATCHDOG_TRIGGER_GPIO 14
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
|
|
/* Use common default */
|
|
|
|
/* Default env settings */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"hostname=rut\0" \
|
|
"ubi_off=2048\0"\
|
|
"nand_img_size=0x500000\0" \
|
|
"splashpos=m,m\0" \
|
|
"optargs=fixrtc --no-log consoleblank=0 \0" \
|
|
CONFIG_ENV_SETTINGS_V1 \
|
|
CONFIG_ENV_SETTINGS_NAND_V1 \
|
|
"mmc_dev=0\0" \
|
|
"mmc_root=/dev/mmcblk0p2 rw\0" \
|
|
"mmc_root_fs_type=ext4 rootwait\0" \
|
|
"mmc_load_uimage=" \
|
|
"mmc rescan; " \
|
|
"setenv bootfile uImage;" \
|
|
"fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
|
|
"loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
|
|
"importbootenv=echo Importing environment from mmc ...; " \
|
|
"env import -t $loadaddr $filesize\0" \
|
|
"mmc_args=run bootargs_defaults;" \
|
|
"mtdparts default;" \
|
|
"setenv bootargs ${bootargs} " \
|
|
"root=${mmc_root} ${mtdparts}" \
|
|
"rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
|
|
"eth=${ethaddr} " \
|
|
"\0" \
|
|
"mmc_boot=run mmc_args; " \
|
|
"run mmc_load_uimage; " \
|
|
"bootm ${kloadaddr}\0" \
|
|
""
|
|
|
|
#ifndef CONFIG_RESTORE_FLASH
|
|
/* set to negative value for no autoboot */
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"if mmc rescan; then " \
|
|
"echo SD/MMC found on device ${mmc_dev};" \
|
|
"if run loadbootenv; then " \
|
|
"echo Loaded environment from ${bootenv};" \
|
|
"run importbootenv;" \
|
|
"fi;" \
|
|
"if test -n $uenvcmd; then " \
|
|
"echo Running uenvcmd ...;" \
|
|
"run uenvcmd;" \
|
|
"fi;" \
|
|
"if run mmc_load_uimage; then " \
|
|
"run mmc_args;" \
|
|
"bootm ${kloadaddr};" \
|
|
"fi;" \
|
|
"fi;" \
|
|
"run nand_boot;" \
|
|
"reset;"
|
|
|
|
#else
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"setenv autoload no; " \
|
|
"dhcp; " \
|
|
"if tftp 80000000 debrick.scr; then " \
|
|
"source 80000000; " \
|
|
"fi"
|
|
#endif
|
|
|
|
#endif /* CONFIG_SPL_BUILD */
|
|
|
|
#if defined(CONFIG_VIDEO)
|
|
#define CONFIG_VIDEO_DA8XX
|
|
#define CONFIG_SPLASH_SCREEN
|
|
#define CONFIG_SPLASH_SCREEN_ALIGN
|
|
#define CONFIG_VIDEO_LOGO
|
|
#define CONFIG_VIDEO_BMP_RLE8
|
|
#define CONFIG_VIDEO_BMP_LOGO
|
|
#define DA8XX_LCD_CNTL_BASE LCD_CNTL_BASE
|
|
|
|
#define BOARD_LCD_RESET 115 /* Bank 3 pin 19 */
|
|
#define CONFIG_FORMIKE
|
|
#define DISPL_PLL_SPREAD_SPECTRUM
|
|
#endif
|
|
|
|
#endif /* ! __CONFIG_RUT_H */
|