mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-06 13:14:27 +00:00
3c41728d80
Current codes assume the OPTEE address is at the end of first DRAM bank. Adjust the process to allow OPTEE in the middle of first bank. When OPTEE memory is removed from first bank, it may split the first bank to two banks, adjust the MMU table for the split case, Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge i.MX8MP evk to default to avoid issue. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com> Tested-by: Silvano di Ninno <silvano.dininno@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
89 lines
2 KiB
C
89 lines
2 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2020 NXP
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <env.h>
|
|
#include <init.h>
|
|
#include <malloc.h>
|
|
#include <errno.h>
|
|
#include <asm/io.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm-generic/gpio.h>
|
|
#include <fsl_esdhc_imx.h>
|
|
#include <mmc.h>
|
|
#include <asm/arch/imx8mq_pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/mach-imx/gpio.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <spl.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
|
|
|
|
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
|
|
|
|
static iomux_v3_cfg_t const wdog_pads[] = {
|
|
IMX8MQ_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const uart_pads[] = {
|
|
IMX8MQ_PAD_UART1_RXD__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
IMX8MQ_PAD_UART1_TXD__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
|
|
|
|
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
|
|
set_wdog_reset(wdog);
|
|
|
|
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_FEC_MXC
|
|
static int setup_fec(void)
|
|
{
|
|
struct iomuxc_gpr_base_regs *gpr =
|
|
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
|
|
|
|
/* Use 125M anatop REF_CLK1 for ENET1, not from external */
|
|
clrsetbits_le32(&gpr->gpr[1], BIT(13) | BIT(17), 0);
|
|
return set_clk_enet(ENET_125MHZ);
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
/* enable rgmii rxc skew and phy mode select to RGMII copper */
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
|
|
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_init(void)
|
|
{
|
|
#ifdef CONFIG_FEC_MXC
|
|
setup_fec();
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_mmc_get_env_dev(int devno)
|
|
{
|
|
return devno;
|
|
}
|