mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 02:51:00 +00:00
fcb624be47
Support Holtek HT1380/HT1381 Serial Timekeeper Chip. It provides seconds , minutes, hours, day of the week, date, month and year information. Datasheet: https://www.holtek.com.tw/documents/10179/11842/ht1380_1v130.pdf Signed-off-by: Sergei Antonov <saproj@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
329 lines
6.5 KiB
C
329 lines
6.5 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Holtek HT1380/HT1381 Serial Timekeeper Chip
|
|
*
|
|
* Communication with the chip is vendor-specific.
|
|
* It is done via 3 GPIO pins: reset, clock, and data.
|
|
* Describe in .dts this way:
|
|
*
|
|
* rtc {
|
|
* compatible = "holtek,ht1380";
|
|
* rst-gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
* clk-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
* dat-gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
|
|
* };
|
|
*
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <rtc.h>
|
|
#include <bcd.h>
|
|
#include <asm/gpio.h>
|
|
#include <linux/delay.h>
|
|
|
|
struct ht1380_priv {
|
|
struct gpio_desc rst_desc;
|
|
struct gpio_desc clk_desc;
|
|
struct gpio_desc dat_desc;
|
|
};
|
|
|
|
enum registers {
|
|
SEC,
|
|
MIN,
|
|
HOUR,
|
|
MDAY,
|
|
MONTH,
|
|
WDAY,
|
|
YEAR,
|
|
WP,
|
|
N_REGS
|
|
};
|
|
|
|
enum hour_mode {
|
|
AMPM_MODE = 0x80, /* RTC is in AM/PM mode */
|
|
PM_NOW = 0x20, /* set if PM, clear if AM */
|
|
};
|
|
|
|
static const int BURST = 0xbe;
|
|
static const int READ = 1;
|
|
|
|
static void ht1380_half_period_delay(void)
|
|
{
|
|
/*
|
|
* Delay for half a period. 1 us complies with the 500 KHz maximum
|
|
* input serial clock limit given by the datasheet.
|
|
*/
|
|
udelay(1);
|
|
}
|
|
|
|
static int ht1380_send_byte(struct ht1380_priv *priv, int byte)
|
|
{
|
|
int ret;
|
|
|
|
for (int bit = 0; bit < 8; bit++) {
|
|
ret = dm_gpio_set_value(&priv->dat_desc, byte >> bit & 1);
|
|
if (ret)
|
|
break;
|
|
ht1380_half_period_delay();
|
|
|
|
ret = dm_gpio_set_value(&priv->clk_desc, 1);
|
|
if (ret)
|
|
break;
|
|
ht1380_half_period_delay();
|
|
|
|
ret = dm_gpio_set_value(&priv->clk_desc, 0);
|
|
if (ret)
|
|
break;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Leave reset state. The transfer operation can then be started.
|
|
*/
|
|
static int ht1380_reset_off(struct ht1380_priv *priv)
|
|
{
|
|
const unsigned int T_CC = 4; /* us, Reset to Clock Setup */
|
|
int ret;
|
|
|
|
/*
|
|
* Leave RESET state.
|
|
* Make sure we make the minimal delay required by the datasheet.
|
|
*/
|
|
ret = dm_gpio_set_value(&priv->rst_desc, 0);
|
|
udelay(T_CC);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Enter reset state. Completes the transfer operation.
|
|
*/
|
|
static int ht1380_reset_on(struct ht1380_priv *priv)
|
|
{
|
|
const unsigned int T_CWH = 4; /* us, Reset Inactive Time */
|
|
int ret;
|
|
|
|
/*
|
|
* Enter RESET state.
|
|
* Make sure we make the minimal delay required by the datasheet.
|
|
*/
|
|
ret = dm_gpio_set_value(&priv->rst_desc, 1);
|
|
udelay(T_CWH);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ht1380_rtc_get(struct udevice *dev, struct rtc_time *tm)
|
|
{
|
|
struct ht1380_priv *priv = dev_get_priv(dev);
|
|
int ret, i, bit, reg[N_REGS];
|
|
|
|
ret = dm_gpio_set_value(&priv->clk_desc, 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = dm_gpio_set_dir_flags(&priv->dat_desc, GPIOD_IS_OUT);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = ht1380_reset_off(priv);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = ht1380_send_byte(priv, BURST + READ);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = dm_gpio_set_dir_flags(&priv->dat_desc, GPIOD_IS_IN);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
for (i = 0; i < N_REGS; i++) {
|
|
reg[i] = 0;
|
|
|
|
for (bit = 0; bit < 8; bit++) {
|
|
ht1380_half_period_delay();
|
|
|
|
ret = dm_gpio_set_value(&priv->clk_desc, 1);
|
|
if (ret)
|
|
goto exit;
|
|
ht1380_half_period_delay();
|
|
|
|
reg[i] |= dm_gpio_get_value(&priv->dat_desc) << bit;
|
|
ret = dm_gpio_set_value(&priv->clk_desc, 0);
|
|
if (ret)
|
|
goto exit;
|
|
}
|
|
}
|
|
|
|
ret = -EINVAL;
|
|
|
|
/* Correctness check: some bits are always zero */
|
|
if (reg[MIN] & 0x80 || reg[HOUR] & 0x40 || reg[MDAY] & 0xc0 ||
|
|
reg[MONTH] & 0xe0 || reg[WDAY] & 0xf8 || reg[WP] & 0x7f)
|
|
goto exit;
|
|
|
|
/* Correctness check: some registers are always non-zero */
|
|
if (!reg[MDAY] || !reg[MONTH] || !reg[WDAY])
|
|
goto exit;
|
|
|
|
tm->tm_sec = bcd2bin(reg[SEC]);
|
|
tm->tm_min = bcd2bin(reg[MIN]);
|
|
if (reg[HOUR] & AMPM_MODE) {
|
|
/* AM-PM Mode, range is 01-12 */
|
|
tm->tm_hour = bcd2bin(reg[HOUR] & 0x1f) % 12;
|
|
if (reg[HOUR] & PM_NOW) {
|
|
/* it is PM (otherwise AM) */
|
|
tm->tm_hour += 12;
|
|
}
|
|
} else {
|
|
/* 24-hour Mode, range is 0-23 */
|
|
tm->tm_hour = bcd2bin(reg[HOUR]);
|
|
}
|
|
tm->tm_mday = bcd2bin(reg[MDAY]);
|
|
tm->tm_mon = bcd2bin(reg[MONTH]);
|
|
tm->tm_year = 2000 + bcd2bin(reg[YEAR]);
|
|
tm->tm_wday = bcd2bin(reg[WDAY]) - 1;
|
|
tm->tm_yday = 0;
|
|
tm->tm_isdst = 0;
|
|
|
|
ret = 0;
|
|
|
|
exit:
|
|
ht1380_reset_on(priv);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ht1380_write_protection_off(struct ht1380_priv *priv)
|
|
{
|
|
int ret;
|
|
const int PROTECT = 0x8e;
|
|
|
|
ret = ht1380_reset_off(priv);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = ht1380_send_byte(priv, PROTECT);
|
|
if (ret)
|
|
return ret;
|
|
ret = ht1380_send_byte(priv, 0); /* WP bit is 0 */
|
|
if (ret)
|
|
return ret;
|
|
|
|
return ht1380_reset_on(priv);
|
|
}
|
|
|
|
static int ht1380_rtc_set(struct udevice *dev, const struct rtc_time *tm)
|
|
{
|
|
struct ht1380_priv *priv = dev_get_priv(dev);
|
|
int ret, i, reg[N_REGS];
|
|
|
|
ret = dm_gpio_set_value(&priv->clk_desc, 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = dm_gpio_set_dir_flags(&priv->dat_desc, GPIOD_IS_OUT);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = ht1380_write_protection_off(priv);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
reg[SEC] = bin2bcd(tm->tm_sec);
|
|
reg[MIN] = bin2bcd(tm->tm_min);
|
|
reg[HOUR] = bin2bcd(tm->tm_hour);
|
|
reg[MDAY] = bin2bcd(tm->tm_mday);
|
|
reg[MONTH] = bin2bcd(tm->tm_mon);
|
|
reg[WDAY] = bin2bcd(tm->tm_wday) + 1;
|
|
reg[YEAR] = bin2bcd(tm->tm_year - 2000);
|
|
reg[WP] = 0x80; /* WP bit is 1 */
|
|
|
|
ret = ht1380_reset_off(priv);
|
|
if (ret)
|
|
goto exit;
|
|
|
|
ret = ht1380_send_byte(priv, BURST);
|
|
for (i = 0; i < N_REGS && ret; i++)
|
|
ret = ht1380_send_byte(priv, reg[i]);
|
|
|
|
exit:
|
|
ht1380_reset_on(priv);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int ht1380_probe(struct udevice *dev)
|
|
{
|
|
int ret;
|
|
struct ht1380_priv *priv;
|
|
|
|
priv = dev_get_priv(dev);
|
|
if (!priv)
|
|
return -EINVAL;
|
|
|
|
ret = gpio_request_by_name(dev, "rst-gpios", 0,
|
|
&priv->rst_desc, GPIOD_IS_OUT);
|
|
if (ret)
|
|
goto fail_rst;
|
|
|
|
ret = gpio_request_by_name(dev, "clk-gpios", 0,
|
|
&priv->clk_desc, GPIOD_IS_OUT);
|
|
if (ret)
|
|
goto fail_clk;
|
|
|
|
ret = gpio_request_by_name(dev, "dat-gpios", 0,
|
|
&priv->dat_desc, 0);
|
|
if (ret)
|
|
goto fail_dat;
|
|
|
|
ret = ht1380_reset_on(priv);
|
|
if (ret)
|
|
goto fail;
|
|
|
|
return 0;
|
|
|
|
fail:
|
|
dm_gpio_free(dev, &priv->dat_desc);
|
|
fail_dat:
|
|
dm_gpio_free(dev, &priv->clk_desc);
|
|
fail_clk:
|
|
dm_gpio_free(dev, &priv->rst_desc);
|
|
fail_rst:
|
|
return ret;
|
|
}
|
|
|
|
static int ht1380_remove(struct udevice *dev)
|
|
{
|
|
struct ht1380_priv *priv = dev_get_priv(dev);
|
|
|
|
dm_gpio_free(dev, &priv->rst_desc);
|
|
dm_gpio_free(dev, &priv->clk_desc);
|
|
dm_gpio_free(dev, &priv->dat_desc);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct rtc_ops ht1380_rtc_ops = {
|
|
.get = ht1380_rtc_get,
|
|
.set = ht1380_rtc_set,
|
|
};
|
|
|
|
static const struct udevice_id ht1380_rtc_ids[] = {
|
|
{ .compatible = "holtek,ht1380" },
|
|
{ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(rtc_ht1380) = {
|
|
.name = "rtc-ht1380",
|
|
.id = UCLASS_RTC,
|
|
.probe = ht1380_probe,
|
|
.remove = ht1380_remove,
|
|
.of_match = ht1380_rtc_ids,
|
|
.ops = &ht1380_rtc_ops,
|
|
.priv_auto = sizeof(struct ht1380_priv),
|
|
};
|