u-boot/board/freescale/ls1021atwr/ls1021atwr.c
Alison Wang 5d267ec679 arm: ls1021atwr: Enable RGMII TX/RX clock internal delay for AR8033
Since commit ce412b7, RGMII TX clock internal delay is not enabled
for AR8033 unconditionally. On LS1021ATWR board, the third port
eTSEC3 uses AR8033 in RGMII mode. The TX/RX internal delay needs to
be enabled.

This patch will set PHY_INTERFACE_MODE_RGMII_ID to enable RGMII TX/RX
clock internal delay for AR8033 on the third port.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-24 08:59:43 -07:00

771 lines
18 KiB
C

/*
* Copyright 2014 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#include <asm/io.h>
#include <asm/arch/immap_ls102xa.h>
#include <asm/arch/clock.h>
#include <asm/arch/fsl_serdes.h>
#include <asm/arch/ls102xa_devdis.h>
#include <asm/arch/ls102xa_soc.h>
#include <asm/arch/ls102xa_sata.h>
#include <hwconfig.h>
#include <mmc.h>
#include <fsl_csu.h>
#include <fsl_esdhc.h>
#include <fsl_ifc.h>
#include <fsl_immap.h>
#include <netdev.h>
#include <fsl_mdio.h>
#include <tsec.h>
#include <fsl_sec.h>
#include <fsl_devdis.h>
#include <spl.h>
#include "../common/sleep.h"
#ifdef CONFIG_U_QE
#include <fsl_qe.h>
#endif
#include <fsl_validate.h>
DECLARE_GLOBAL_DATA_PTR;
#define VERSION_MASK 0x00FF
#define BANK_MASK 0x0001
#define CONFIG_RESET 0x1
#define INIT_RESET 0x1
#define CPLD_SET_MUX_SERDES 0x20
#define CPLD_SET_BOOT_BANK 0x40
#define BOOT_FROM_UPPER_BANK 0x0
#define BOOT_FROM_LOWER_BANK 0x1
#define LANEB_SATA (0x01)
#define LANEB_SGMII1 (0x02)
#define LANEC_SGMII1 (0x04)
#define LANEC_PCIEX1 (0x08)
#define LANED_PCIEX2 (0x10)
#define LANED_SGMII2 (0x20)
#define MASK_LANE_B 0x1
#define MASK_LANE_C 0x2
#define MASK_LANE_D 0x4
#define MASK_SGMII 0x8
#define KEEP_STATUS 0x0
#define NEED_RESET 0x1
#define SOFT_MUX_ON_I2C3_IFC 0x2
#define SOFT_MUX_ON_CAN3_USB2 0x8
#define SOFT_MUX_ON_QE_LCD 0x10
#define PIN_I2C3_IFC_MUX_I2C3 0x0
#define PIN_I2C3_IFC_MUX_IFC 0x1
#define PIN_CAN3_USB2_MUX_USB2 0x0
#define PIN_CAN3_USB2_MUX_CAN3 0x1
#define PIN_QE_LCD_MUX_LCD 0x0
#define PIN_QE_LCD_MUX_QE 0x1
struct cpld_data {
u8 cpld_ver; /* cpld revision */
u8 cpld_ver_sub; /* cpld sub revision */
u8 pcba_ver; /* pcb revision number */
u8 system_rst; /* reset system by cpld */
u8 soft_mux_on; /* CPLD override physical switches Enable */
u8 cfg_rcw_src1; /* Reset config word 1 */
u8 cfg_rcw_src2; /* Reset config word 2 */
u8 vbank; /* Flash bank selection Control */
u8 gpio; /* GPIO for TWR-ELEV */
u8 i2c3_ifc_mux;
u8 mux_spi2;
u8 can3_usb2_mux; /* CAN3 and USB2 Selection */
u8 qe_lcd_mux; /* QE and LCD Selection */
u8 serdes_mux; /* Multiplexed pins for SerDes Lanes */
u8 global_rst; /* reset with init CPLD reg to default */
u8 rev1; /* Reserved */
u8 rev2; /* Reserved */
};
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
static void convert_serdes_mux(int type, int need_reset);
void cpld_show(void)
{
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
printf("CPLD: V%x.%x\nPCBA: V%x.0\nVBank: %d\n",
in_8(&cpld_data->cpld_ver) & VERSION_MASK,
in_8(&cpld_data->cpld_ver_sub) & VERSION_MASK,
in_8(&cpld_data->pcba_ver) & VERSION_MASK,
in_8(&cpld_data->vbank) & BANK_MASK);
#ifdef CONFIG_DEBUG
printf("soft_mux_on =%x\n",
in_8(&cpld_data->soft_mux_on));
printf("cfg_rcw_src1 =%x\n",
in_8(&cpld_data->cfg_rcw_src1));
printf("cfg_rcw_src2 =%x\n",
in_8(&cpld_data->cfg_rcw_src2));
printf("vbank =%x\n",
in_8(&cpld_data->vbank));
printf("gpio =%x\n",
in_8(&cpld_data->gpio));
printf("i2c3_ifc_mux =%x\n",
in_8(&cpld_data->i2c3_ifc_mux));
printf("mux_spi2 =%x\n",
in_8(&cpld_data->mux_spi2));
printf("can3_usb2_mux =%x\n",
in_8(&cpld_data->can3_usb2_mux));
printf("qe_lcd_mux =%x\n",
in_8(&cpld_data->qe_lcd_mux));
printf("serdes_mux =%x\n",
in_8(&cpld_data->serdes_mux));
#endif
}
#endif
int checkboard(void)
{
puts("Board: LS1021ATWR\n");
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
cpld_show();
#endif
return 0;
}
void ddrmc_init(void)
{
struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR;
u32 temp_sdram_cfg, tmp;
out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG);
out_be32(&ddr->cs0_bnds, DDR_CS0_BNDS);
out_be32(&ddr->cs0_config, DDR_CS0_CONFIG);
out_be32(&ddr->timing_cfg_0, DDR_TIMING_CFG_0);
out_be32(&ddr->timing_cfg_1, DDR_TIMING_CFG_1);
out_be32(&ddr->timing_cfg_2, DDR_TIMING_CFG_2);
out_be32(&ddr->timing_cfg_3, DDR_TIMING_CFG_3);
out_be32(&ddr->timing_cfg_4, DDR_TIMING_CFG_4);
out_be32(&ddr->timing_cfg_5, DDR_TIMING_CFG_5);
#ifdef CONFIG_DEEP_SLEEP
if (is_warm_boot()) {
out_be32(&ddr->sdram_cfg_2,
DDR_SDRAM_CFG_2 & ~SDRAM_CFG2_D_INIT);
out_be32(&ddr->init_addr, CONFIG_SYS_SDRAM_BASE);
out_be32(&ddr->init_ext_addr, (1 << 31));
/* DRAM VRef will not be trained */
out_be32(&ddr->ddr_cdr2,
DDR_DDR_CDR2 & ~DDR_CDR2_VREF_TRAIN_EN);
} else
#endif
{
out_be32(&ddr->sdram_cfg_2, DDR_SDRAM_CFG_2);
out_be32(&ddr->ddr_cdr2, DDR_DDR_CDR2);
}
out_be32(&ddr->sdram_mode, DDR_SDRAM_MODE);
out_be32(&ddr->sdram_mode_2, DDR_SDRAM_MODE_2);
out_be32(&ddr->sdram_interval, DDR_SDRAM_INTERVAL);
out_be32(&ddr->ddr_wrlvl_cntl, DDR_DDR_WRLVL_CNTL);
out_be32(&ddr->ddr_wrlvl_cntl_2, DDR_DDR_WRLVL_CNTL_2);
out_be32(&ddr->ddr_wrlvl_cntl_3, DDR_DDR_WRLVL_CNTL_3);
out_be32(&ddr->ddr_cdr1, DDR_DDR_CDR1);
out_be32(&ddr->sdram_clk_cntl, DDR_SDRAM_CLK_CNTL);
out_be32(&ddr->ddr_zq_cntl, DDR_DDR_ZQ_CNTL);
out_be32(&ddr->cs0_config_2, DDR_CS0_CONFIG_2);
/* DDR erratum A-009942 */
tmp = in_be32(&ddr->debug[28]);
out_be32(&ddr->debug[28], tmp | 0x0070006f);
udelay(1);
#ifdef CONFIG_DEEP_SLEEP
if (is_warm_boot()) {
/* enter self-refresh */
temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2);
temp_sdram_cfg |= SDRAM_CFG2_FRC_SR;
out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg);
temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN | SDRAM_CFG_BI);
} else
#endif
temp_sdram_cfg = (DDR_SDRAM_CFG_MEM_EN & ~SDRAM_CFG_BI);
out_be32(&ddr->sdram_cfg, DDR_SDRAM_CFG | temp_sdram_cfg);
#ifdef CONFIG_DEEP_SLEEP
if (is_warm_boot()) {
/* exit self-refresh */
temp_sdram_cfg = in_be32(&ddr->sdram_cfg_2);
temp_sdram_cfg &= ~SDRAM_CFG2_FRC_SR;
out_be32(&ddr->sdram_cfg_2, temp_sdram_cfg);
}
#endif
}
int dram_init(void)
{
#if (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD))
ddrmc_init();
#endif
gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
fsl_dp_resume();
#endif
return 0;
}
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg esdhc_cfg[1] = {
{CONFIG_SYS_FSL_ESDHC_ADDR},
};
int board_mmc_init(bd_t *bis)
{
esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
}
#endif
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_TSEC_ENET
struct fsl_pq_mdio_info mdio_info;
struct tsec_info_struct tsec_info[4];
int num = 0;
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
if (is_serdes_configured(SGMII_TSEC1)) {
puts("eTSEC1 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
#ifdef CONFIG_TSEC2
SET_STD_TSEC_INFO(tsec_info[num], 2);
if (is_serdes_configured(SGMII_TSEC2)) {
puts("eTSEC2 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
#ifdef CONFIG_TSEC3
SET_STD_TSEC_INFO(tsec_info[num], 3);
tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID;
num++;
#endif
if (!num) {
printf("No TSECs initialized\n");
return 0;
}
mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
mdio_info.name = DEFAULT_MII_NAME;
fsl_pq_mdio_init(bis, &mdio_info);
tsec_eth_init(bis, tsec_info, num);
#endif
return pci_eth_init(bis);
}
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
int config_serdes_mux(void)
{
struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
u32 protocol = in_be32(&gur->rcwsr[4]) & RCWSR4_SRDS1_PRTCL_MASK;
protocol >>= RCWSR4_SRDS1_PRTCL_SHIFT;
switch (protocol) {
case 0x10:
convert_serdes_mux(LANEB_SATA, KEEP_STATUS);
convert_serdes_mux(LANED_PCIEX2 |
LANEC_PCIEX1, KEEP_STATUS);
break;
case 0x20:
convert_serdes_mux(LANEB_SGMII1, KEEP_STATUS);
convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS);
convert_serdes_mux(LANED_SGMII2, KEEP_STATUS);
break;
case 0x30:
convert_serdes_mux(LANEB_SATA, KEEP_STATUS);
convert_serdes_mux(LANEC_SGMII1, KEEP_STATUS);
convert_serdes_mux(LANED_SGMII2, KEEP_STATUS);
break;
case 0x70:
convert_serdes_mux(LANEB_SATA, KEEP_STATUS);
convert_serdes_mux(LANEC_PCIEX1, KEEP_STATUS);
convert_serdes_mux(LANED_SGMII2, KEEP_STATUS);
break;
}
return 0;
}
#endif
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
int config_board_mux(void)
{
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
int conflict_flag;
conflict_flag = 0;
if (hwconfig("i2c3")) {
conflict_flag++;
cpld_data->soft_mux_on |= SOFT_MUX_ON_I2C3_IFC;
cpld_data->i2c3_ifc_mux = PIN_I2C3_IFC_MUX_I2C3;
}
if (hwconfig("ifc")) {
conflict_flag++;
/* some signals can not enable simultaneous*/
if (conflict_flag > 1)
goto conflict;
cpld_data->soft_mux_on |= SOFT_MUX_ON_I2C3_IFC;
cpld_data->i2c3_ifc_mux = PIN_I2C3_IFC_MUX_IFC;
}
conflict_flag = 0;
if (hwconfig("usb2")) {
conflict_flag++;
cpld_data->soft_mux_on |= SOFT_MUX_ON_CAN3_USB2;
cpld_data->can3_usb2_mux = PIN_CAN3_USB2_MUX_USB2;
}
if (hwconfig("can3")) {
conflict_flag++;
/* some signals can not enable simultaneous*/
if (conflict_flag > 1)
goto conflict;
cpld_data->soft_mux_on |= SOFT_MUX_ON_CAN3_USB2;
cpld_data->can3_usb2_mux = PIN_CAN3_USB2_MUX_CAN3;
}
conflict_flag = 0;
if (hwconfig("lcd")) {
conflict_flag++;
cpld_data->soft_mux_on |= SOFT_MUX_ON_QE_LCD;
cpld_data->qe_lcd_mux = PIN_QE_LCD_MUX_LCD;
}
if (hwconfig("qe")) {
conflict_flag++;
/* some signals can not enable simultaneous*/
if (conflict_flag > 1)
goto conflict;
cpld_data->soft_mux_on |= SOFT_MUX_ON_QE_LCD;
cpld_data->qe_lcd_mux = PIN_QE_LCD_MUX_QE;
}
return 0;
conflict:
printf("WARNING: pin conflict! MUX setting may failed!\n");
return 0;
}
#endif
int board_early_init_f(void)
{
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
#ifdef CONFIG_TSEC_ENET
/* clear BD & FR bits for BE BD's and frame data */
clrbits_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
#endif
#ifdef CONFIG_FSL_IFC
init_early_memctl_regs();
#endif
arch_soc_init();
#if defined(CONFIG_DEEP_SLEEP)
if (is_warm_boot()) {
timer_init();
dram_init();
}
#endif
return 0;
}
#ifdef CONFIG_SPL_BUILD
void board_init_f(ulong dummy)
{
void (*second_uboot)(void);
/* Clear the BSS */
memset(__bss_start, 0, __bss_end - __bss_start);
get_clocks();
#if defined(CONFIG_DEEP_SLEEP)
if (is_warm_boot())
fsl_dp_disable_console();
#endif
preloader_console_init();
dram_init();
/* Allow OCRAM access permission as R/W */
#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
enable_layerscape_ns_access();
enable_layerscape_ns_access();
#endif
/*
* if it is woken up from deep sleep, then jump to second
* stage uboot and continue executing without recopying
* it from SD since it has already been reserved in memeory
* in last boot.
*/
if (is_warm_boot()) {
second_uboot = (void (*)(void))CONFIG_SYS_TEXT_BASE;
second_uboot();
}
board_init_r(NULL, 0);
}
#endif
#ifdef CONFIG_DEEP_SLEEP
/* program the regulator (MC34VR500) to support deep sleep */
void ls1twr_program_regulator(void)
{
unsigned int i2c_bus;
u8 i2c_device_id;
#define LS1TWR_I2C_BUS_MC34VR500 1
#define MC34VR500_ADDR 0x8
#define MC34VR500_DEVICEID 0x4
#define MC34VR500_DEVICEID_MASK 0x0f
i2c_bus = i2c_get_bus_num();
i2c_set_bus_num(LS1TWR_I2C_BUS_MC34VR500);
i2c_device_id = i2c_reg_read(MC34VR500_ADDR, 0x0) &
MC34VR500_DEVICEID_MASK;
if (i2c_device_id != MC34VR500_DEVICEID) {
printf("The regulator (MC34VR500) does not exist. The device does not support deep sleep.\n");
return;
}
i2c_reg_write(MC34VR500_ADDR, 0x31, 0x4);
i2c_reg_write(MC34VR500_ADDR, 0x4d, 0x4);
i2c_reg_write(MC34VR500_ADDR, 0x6d, 0x38);
i2c_reg_write(MC34VR500_ADDR, 0x6f, 0x37);
i2c_reg_write(MC34VR500_ADDR, 0x71, 0x30);
i2c_set_bus_num(i2c_bus);
}
#endif
int board_init(void)
{
#ifdef CONFIG_SYS_FSL_ERRATUM_A010315
erratum_a010315();
#endif
#ifndef CONFIG_SYS_FSL_NO_SERDES
fsl_serdes_init();
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
config_serdes_mux();
#endif
#endif
ls102xa_smmu_stream_id_init();
#ifdef CONFIG_U_QE
u_qe_init();
#endif
#ifdef CONFIG_DEEP_SLEEP
ls1twr_program_regulator();
#endif
return 0;
}
#if defined(CONFIG_SPL_BUILD)
void spl_board_init(void)
{
ls102xa_smmu_stream_id_init();
}
#endif
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
#ifdef CONFIG_SCSI_AHCI_PLAT
ls1021a_sata_init();
#endif
#ifdef CONFIG_CHAIN_OF_TRUST
fsl_setenv_chain_of_trust();
#endif
return 0;
}
#endif
#if defined(CONFIG_MISC_INIT_R)
int misc_init_r(void)
{
#ifdef CONFIG_FSL_DEVICE_DISABLE
device_disable(devdis_tbl, ARRAY_SIZE(devdis_tbl));
#endif
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
config_board_mux();
#endif
#ifdef CONFIG_FSL_CAAM
return sec_init();
#endif
}
#endif
#if defined(CONFIG_DEEP_SLEEP)
void board_sleep_prepare(void)
{
#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
enable_layerscape_ns_access();
#endif
}
#endif
int ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
#ifdef CONFIG_PCI
ft_pci_setup(blob, bd);
#endif
return 0;
}
u8 flash_read8(void *addr)
{
return __raw_readb(addr + 1);
}
void flash_write16(u16 val, void *addr)
{
u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
__raw_writew(shftval, addr);
}
u16 flash_read16(void *addr)
{
u16 val = __raw_readw(addr);
return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
}
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
static void convert_flash_bank(char bank)
{
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
printf("Now switch to boot from flash bank %d.\n", bank);
cpld_data->soft_mux_on = CPLD_SET_BOOT_BANK;
cpld_data->vbank = bank;
printf("Reset board to enable configuration.\n");
cpld_data->system_rst = CONFIG_RESET;
}
static int flash_bank_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
{
if (argc != 2)
return CMD_RET_USAGE;
if (strcmp(argv[1], "0") == 0)
convert_flash_bank(BOOT_FROM_UPPER_BANK);
else if (strcmp(argv[1], "1") == 0)
convert_flash_bank(BOOT_FROM_LOWER_BANK);
else
return CMD_RET_USAGE;
return 0;
}
U_BOOT_CMD(
boot_bank, 2, 0, flash_bank_cmd,
"Flash bank Selection Control",
"bank[0-upper bank/1-lower bank] (e.g. boot_bank 0)"
);
static int cpld_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
{
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
if (argc > 2)
return CMD_RET_USAGE;
if ((argc == 1) || (strcmp(argv[1], "conf") == 0))
cpld_data->system_rst = CONFIG_RESET;
else if (strcmp(argv[1], "init") == 0)
cpld_data->global_rst = INIT_RESET;
else
return CMD_RET_USAGE;
return 0;
}
U_BOOT_CMD(
cpld_reset, 2, 0, cpld_reset_cmd,
"Reset via CPLD",
"conf\n"
" -reset with current CPLD configuration\n"
"init\n"
" -reset and initial CPLD configuration with default value"
);
static void convert_serdes_mux(int type, int need_reset)
{
char current_serdes;
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
current_serdes = cpld_data->serdes_mux;
switch (type) {
case LANEB_SATA:
current_serdes &= ~MASK_LANE_B;
break;
case LANEB_SGMII1:
current_serdes |= (MASK_LANE_B | MASK_SGMII | MASK_LANE_C);
break;
case LANEC_SGMII1:
current_serdes &= ~(MASK_LANE_B | MASK_SGMII | MASK_LANE_C);
break;
case LANED_SGMII2:
current_serdes |= MASK_LANE_D;
break;
case LANEC_PCIEX1:
current_serdes |= MASK_LANE_C;
break;
case (LANED_PCIEX2 | LANEC_PCIEX1):
current_serdes |= MASK_LANE_C;
current_serdes &= ~MASK_LANE_D;
break;
default:
printf("CPLD serdes MUX: unsupported MUX type 0x%x\n", type);
return;
}
cpld_data->soft_mux_on |= CPLD_SET_MUX_SERDES;
cpld_data->serdes_mux = current_serdes;
if (need_reset == 1) {
printf("Reset board to enable configuration\n");
cpld_data->system_rst = CONFIG_RESET;
}
}
void print_serdes_mux(void)
{
char current_serdes;
struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
current_serdes = cpld_data->serdes_mux;
printf("Serdes Lane B: ");
if ((current_serdes & MASK_LANE_B) == 0)
printf("SATA,\n");
else
printf("SGMII 1,\n");
printf("Serdes Lane C: ");
if ((current_serdes & MASK_LANE_C) == 0)
printf("SGMII 1,\n");
else
printf("PCIe,\n");
printf("Serdes Lane D: ");
if ((current_serdes & MASK_LANE_D) == 0)
printf("PCIe,\n");
else
printf("SGMII 2,\n");
printf("SGMII 1 is on lane ");
if ((current_serdes & MASK_SGMII) == 0)
printf("C.\n");
else
printf("B.\n");
}
static int serdes_mux_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
{
if (argc != 2)
return CMD_RET_USAGE;
if (strcmp(argv[1], "sata") == 0) {
printf("Set serdes lane B to SATA.\n");
convert_serdes_mux(LANEB_SATA, NEED_RESET);
} else if (strcmp(argv[1], "sgmii1b") == 0) {
printf("Set serdes lane B to SGMII 1.\n");
convert_serdes_mux(LANEB_SGMII1, NEED_RESET);
} else if (strcmp(argv[1], "sgmii1c") == 0) {
printf("Set serdes lane C to SGMII 1.\n");
convert_serdes_mux(LANEC_SGMII1, NEED_RESET);
} else if (strcmp(argv[1], "sgmii2") == 0) {
printf("Set serdes lane D to SGMII 2.\n");
convert_serdes_mux(LANED_SGMII2, NEED_RESET);
} else if (strcmp(argv[1], "pciex1") == 0) {
printf("Set serdes lane C to PCIe X1.\n");
convert_serdes_mux(LANEC_PCIEX1, NEED_RESET);
} else if (strcmp(argv[1], "pciex2") == 0) {
printf("Set serdes lane C & lane D to PCIe X2.\n");
convert_serdes_mux((LANED_PCIEX2 | LANEC_PCIEX1), NEED_RESET);
} else if (strcmp(argv[1], "show") == 0) {
print_serdes_mux();
} else {
return CMD_RET_USAGE;
}
return 0;
}
U_BOOT_CMD(
lane_bank, 2, 0, serdes_mux_cmd,
"Multiplexed function setting for SerDes Lanes",
"sata\n"
" -change lane B to sata\n"
"lane_bank sgmii1b\n"
" -change lane B to SGMII1\n"
"lane_bank sgmii1c\n"
" -change lane C to SGMII1\n"
"lane_bank sgmii2\n"
" -change lane D to SGMII2\n"
"lane_bank pciex1\n"
" -change lane C to PCIeX1\n"
"lane_bank pciex2\n"
" -change lane C & lane D to PCIeX2\n"
"\nWARNING: If you aren't familiar with the setting of serdes, don't try to change anything!\n"
);
#endif