u-boot/include/configs/ep8260.h
Wolfgang Denk 700a0c648d Add common (with Linux) MTD partition scheme and "mtdparts" command
Old, obsolete and duplicated code was cleaned up and replace by the
new partitioning method. There are two possible approaches now:
* define a single, static partition
* use mtdparts command line option and dynamic partitioning
Default is static partitioning.
2005-08-08 01:03:24 +02:00

765 lines
23 KiB
C

/*
* (C) Copyright 2002
* Frank Panno <fpanno@delphintech.com>, Delphin Technology AG
*
* This file is based on similar values for other boards found in other
* U-Boot config files, and some that I found in the EP8260 manual.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*
* "EP8260 H, V.1.1"
* - 64M 60x Bus SDRAM
* - 32M Local Bus SDRAM
* - 16M Flash (4 x AM29DL323DB90WDI)
* - 128k NVRAM with RTC
*
* "EP8260 H2, V.1.3" (CFG_EP8260_H2)
* - 300MHz/133MHz/66MHz
* - 64M 60x Bus SDRAM
* - 32M Local Bus SDRAM
* - 32M Flash
* - 128k NVRAM with RTC
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* Define this to enable support the EP8260 H2 version */
#define CFG_EP8260_H2 1
/* #undef CFG_EP8260_H2 */
#define CONFIG_CPM2 1 /* Has a CPM2 */
/* What is the oscillator's (UX2) frequency in Hz? */
#define CONFIG_8260_CLKIN (66 * 1000 * 1000)
/*-----------------------------------------------------------------------
* MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual
*-----------------------------------------------------------------------
* What should MODCK_H be? It is dependent on the oscillator
* frequency, MODCK[1-3], and desired CPM and core frequencies.
* Here are some example values (all frequencies are in MHz):
*
* MODCK_H MODCK[1-3] Osc CPM Core
* ------- ---------- --- --- ----
* 0x2 0x2 33 133 133
* 0x2 0x3 33 133 166
* 0x2 0x4 33 133 200
* 0x2 0x5 33 133 233
* 0x2 0x6 33 133 266
*
* 0x5 0x5 66 133 133
* 0x5 0x6 66 133 166
* 0x5 0x7 66 133 200 *
* 0x6 0x0 66 133 233
* 0x6 0x1 66 133 266
* 0x6 0x2 66 133 300
*/
#ifdef CFG_EP8260_H2
#define CFG_SBC_MODCK_H (HRCW_MODCK_H0110)
#else
#define CFG_SBC_MODCK_H (HRCW_MODCK_H0110)
#endif
/* Define this if you want to boot from 0x00000100. If you don't define
* this, you will need to program the bootloader to 0xfff00000, and
* get the hardware reset config words at 0xfe000000. The simplest
* way to do that is to program the bootloader at both addresses.
* It is suggested that you just let U-Boot live at 0x00000000.
*/
/* #define CFG_SBC_BOOT_LOW 1 */ /* only for HRCW */
/* #undef CFG_SBC_BOOT_LOW */
/* The reset command will not work as expected if the reset address does
* not point to the correct address.
*/
#define CFG_RESET_ADDRESS 0xFFF00100
/* What should the base address of the main FLASH be and how big is
* it (in MBytes)? This must contain TEXT_BASE from board/ep8260/config.mk
* The main FLASH is whichever is connected to *CS0. U-Boot expects
* this to be the SIMM.
*/
#ifdef CFG_EP8260_H2
#define CFG_FLASH0_BASE 0xFE000000
#define CFG_FLASH0_SIZE 32
#else
#define CFG_FLASH0_BASE 0xFF000000
#define CFG_FLASH0_SIZE 16
#endif
/* What should the base address of the secondary FLASH be and how big
* is it (in Mbytes)? The secondary FLASH is whichever is connected
* to *CS6. U-Boot expects this to be the on board FLASH. If you don't
* want it enabled, don't define these constants.
*/
#define CFG_FLASH1_BASE 0
#define CFG_FLASH1_SIZE 0
#undef CFG_FLASH1_BASE
#undef CFG_FLASH1_SIZE
/* What should be the base address of SDRAM DIMM (60x bus) and how big is
* it (in Mbytes)?
*/
#define CFG_SDRAM0_BASE 0x00000000
#define CFG_SDRAM0_SIZE 64
/* define CFG_LSDRAM if you want to enable the 32M SDRAM on the
* local bus (8260 local bus is NOT cacheable!)
*/
/* #define CFG_LSDRAM */
#undef CFG_LSDRAM
#ifdef CFG_LSDRAM
/* What should be the base address of SDRAM DIMM (local bus) and how big is
* it (in Mbytes)?
*/
#define CFG_SDRAM1_BASE 0x04000000
#define CFG_SDRAM1_SIZE 32
#else
#define CFG_SDRAM1_BASE 0
#define CFG_SDRAM1_SIZE 0
#undef CFG_SDRAM1_BASE
#undef CFG_SDRAM1_SIZE
#endif /* CFG_LSDRAM */
/* What should be the base address of NVRAM and how big is
* it (in Bytes)
*/
#define CFG_NVRAM_BASE_ADDR 0xFA080000
#define CFG_NVRAM_SIZE (128*1024)-16
/* The RTC is a Dallas DS1556
*/
#define CONFIG_RTC_DS1556
/* What should be the base address of the LEDs and switch S0?
* If you don't want them enabled, don't define this.
*/
#define CFG_LED_BASE 0x00000000
#undef CFG_LED_BASE
/*
* select serial console configuration
*
* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
* for SCC).
*
* if CONFIG_CONS_NONE is defined, then the serial console routines must
* defined elsewhere.
*/
#define CONFIG_CONS_ON_SMC /* define if console on SMC */
#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
#undef CONFIG_CONS_NONE /* define if console on neither */
#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
/*
* select ethernet configuration
*
* if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
* CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
* for FCC)
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
* defined elsewhere (as for the console), or CFG_CMD_NET must be removed
* from CONFIG_COMMANDS to remove support for networking.
*/
#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */
#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */
#if ( CONFIG_ETHER_INDEX == 3 )
/*
* - Rx-CLK is CLK15
* - Tx-CLK is CLK16
* - RAM for BD/Buffers is on the local Bus (see 28-13)
* - Enable Half Duplex in FSMR
*/
# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
/*
* - RAM for BD/Buffers is on the local Bus (see 28-13)
*/
#ifdef CFG_LSDRAM
#define CFG_CPMFCR_RAMTYPE 3
#else /* CFG_LSDRAM */
#define CFG_CPMFCR_RAMTYPE 0
#endif /* CFG_LSDRAM */
/* - Enable Half Duplex in FSMR */
/* # define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */
# define CFG_FCC_PSMR 0
#else /* CONFIG_ETHER_INDEX */
# error "on EP8260 ethernet must be FCC3"
#endif /* CONFIG_ETHER_INDEX */
/*
* select i2c support configuration
*
* Supported configurations are {none, software, hardware} drivers.
* If the software driver is chosen, there are some additional
* configuration items that the driver uses to drive the port pins.
*/
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
/*
* Software (bit-bang) I2C driver configuration
*/
#ifdef CONFIG_SOFT_I2C
#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
#define I2C_ACTIVE (iop->pdir |= 0x00010000)
#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
#define I2C_READ ((iop->pdat & 0x00010000) != 0)
#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
else iop->pdat &= ~0x00010000
#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
else iop->pdat &= ~0x00020000
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#endif /* CONFIG_SOFT_I2C */
/* #define CONFIG_RTC_DS174x */
/* Define this to reserve an entire FLASH sector (256 KB) for
* environment variables. Otherwise, the environment will be
* put in the same sector as U-Boot, and changing variables
* will erase U-Boot temporarily
*/
#define CFG_ENV_IN_OWN_SECT
/* Define to allow the user to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/* What should the console's baud rate be? */
#ifdef CFG_EP8260_H2
#define CONFIG_BAUDRATE 9600
#else
#define CONFIG_BAUDRATE 115200
#endif
/* Ethernet MAC address */
#define CONFIG_ETHADDR 00:10:EC:00:30:8C
#define CONFIG_IPADDR 192.168.254.130
#define CONFIG_SERVERIP 192.168.254.49
/* Set to a positive value to delay for running BOOTCOMMAND */
#define CONFIG_BOOTDELAY -1
/* undef this to save memory */
#define CFG_LONGHELP
/* Monitor Command Prompt */
#define CFG_PROMPT "=> "
/* Define this variable to enable the "hush" shell (from
Busybox) as command line interpreter, thus enabling
powerful command line syntax like
if...then...else...fi conditionals or `&&' and '||'
constructs ("shell scripts").
If undefined, you get the old, much simpler behaviour
with a somewhat smapper memory footprint.
*/
#define CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
/* What U-Boot subsytems do you want enabled? */
/*
*/
#define CONFIG_COMMANDS ( CFG_CMD_ALL & \
~( CFG_CMD_BMP | \
CFG_CMD_BSP | \
CFG_CMD_DCR | \
CFG_CMD_DHCP | \
CFG_CMD_DOC | \
CFG_CMD_DTT | \
CFG_CMD_EEPROM | \
CFG_CMD_EXT2 | \
CFG_CMD_FDC | \
CFG_CMD_FDOS | \
CFG_CMD_HWFLOW | \
CFG_CMD_IDE | \
CFG_CMD_JFFS2 | \
CFG_CMD_KGDB | \
CFG_CMD_MII | \
CFG_CMD_MMC | \
CFG_CMD_NAND | \
CFG_CMD_PCI | \
CFG_CMD_PCMCIA | \
CFG_CMD_REISER | \
CFG_CMD_SCSI | \
CFG_CMD_SPI | \
CFG_CMD_UNIVERSE| \
CFG_CMD_USB | \
CFG_CMD_VFD | \
CFG_CMD_XIMG ) )
/* Where do the internal registers live? */
#define CFG_IMMR 0xF0000000
#define CFG_DEFAULT_IMMR 0x00010000
/* Where do the on board registers (CS4) live? */
#define CFG_REGS_BASE 0xFA000000
/*****************************************************************************
*
* You should not have to modify any of the following settings
*
*****************************************************************************/
#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
#define CONFIG_EP8260 11 /* on an Embedded Planet EP8260 Board, Rev. 11 */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*
* Miscellaneous configurable options
*/
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16)
#define CFG_MAXARGS 8 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#ifdef CFG_LSDRAM
#define CFG_MEMTEST_START 0x04000000 /* memtest works on */
#define CFG_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
#else
#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
#define CFG_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */
#endif /* CFG_LSDRAM */
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
#define CFG_LOAD_ADDR 0x00100000 /* default load address */
#define CFG_TFTP_LOADADDR 0x00100000 /* default load address for network file downloads */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/* valid baudrates */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CFG_FLASH_BASE CFG_FLASH0_BASE
#define CFG_SDRAM_BASE CFG_SDRAM0_BASE
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*/
#if defined(CFG_SBC_BOOT_LOW)
# define CFG_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
#else
# define CFG_SBC_HRCW_BOOT_FLAGS (0x00000000)
#endif /* defined(CFG_SBC_BOOT_LOW) */
#ifdef CFG_EP8260_H2
/* get the HRCW ISB field from CFG_DEFAULT_IMMR */
#define CFG_SBC_HRCW_IMMR ( ((CFG_DEFAULT_IMMR & 0x10000000) >> 10) |\
((CFG_DEFAULT_IMMR & 0x01000000) >> 7) |\
((CFG_DEFAULT_IMMR & 0x00100000) >> 4) )
#define CFG_HRCW_MASTER (HRCW_EBM |\
HRCW_L2CPC01 |\
CFG_SBC_HRCW_IMMR |\
HRCW_APPC10 |\
HRCW_CS10PC01 |\
CFG_SBC_MODCK_H |\
CFG_SBC_HRCW_BOOT_FLAGS)
#else
#define CFG_HRCW_MASTER 0x10400245
#endif
/* no slaves */
#define CFG_HRCW_SLAVE1 0
#define CFG_HRCW_SLAVE2 0
#define CFG_HRCW_SLAVE3 0
#define CFG_HRCW_SLAVE4 0
#define CFG_HRCW_SLAVE5 0
#define CFG_HRCW_SLAVE6 0
#define CFG_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
* Note also that the logic that sets CFG_RAMBOOT is platform dependent.
*/
#define CFG_MONITOR_BASE TEXT_BASE
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
# define CFG_RAMBOOT
#endif
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#ifdef CFG_EP8260_H2
#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
#else
#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#endif
#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
#ifndef CFG_RAMBOOT
# define CFG_ENV_IS_IN_FLASH 1
# ifdef CFG_ENV_IN_OWN_SECT
# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
# define CFG_ENV_SECT_SIZE 0x40000
# else
# define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_ENV_SECT_SIZE)
# define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
# define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
# endif /* CFG_ENV_IN_OWN_SECT */
#else
# define CFG_ENV_IS_IN_NVRAM 1
# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
# define CFG_ENV_SIZE 0x200
#endif /* CFG_RAMBOOT */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* HIDx - Hardware Implementation-dependent Registers 2-11
*-----------------------------------------------------------------------
* HID0 also contains cache control - initially enable both caches and
* invalidate contents, then the final state leaves only the instruction
* cache enabled. Note that Power-On and Hard reset invalidate the caches,
* but Soft reset does not.
*
* HID1 has only read-only information - nothing to set.
*/
#define CFG_HID0_INIT (HID0_ICE |\
HID0_DCE |\
HID0_ICFI |\
HID0_DCI |\
HID0_IFEM |\
HID0_ABE)
#ifdef CFG_LSDRAM
/* 8260 local bus is NOT cacheable */
#define CFG_HID0_FINAL (/*HID0_ICE |*/\
HID0_IFEM |\
HID0_ABE |\
HID0_EMCP)
#else /* !CFG_LSDRAM */
#define CFG_HID0_FINAL (HID0_ICE |\
HID0_IFEM |\
HID0_ABE |\
HID0_EMCP)
#endif /* CFG_LSDRAM */
#define CFG_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register
*-----------------------------------------------------------------------
*/
#define CFG_RMR 0
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
#define CFG_BCR (BCR_EBM |\
BCR_PLDP |\
BCR_EAV |\
BCR_NPQM0)
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 4-31
*-----------------------------------------------------------------------
*/
#define CFG_SIUMCR (SIUMCR_L2CPC01 |\
SIUMCR_APPC10 |\
SIUMCR_CS10PC01)
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
#ifdef CFG_EP8260_H2
/* TBD: Find out why setting the BMT to 0xff causes the FCC to
* generate TX buffer underrun errors for large packets under
* Linux
*/
#define CFG_SYPCR_BMT 0x00000600
#else
#define CFG_SYPCR_BMT SYPCR_BMT
#endif
#ifdef CFG_LSDRAM
#define CFG_SYPCR (SYPCR_SWTC |\
CFG_SYPCR_BMT |\
SYPCR_PBME |\
SYPCR_LBME |\
SYPCR_SWP)
#else
#define CFG_SYPCR (SYPCR_SWTC |\
CFG_SYPCR_BMT |\
SYPCR_PBME |\
SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* TMCNTSC - Time Counter Status and Control 4-40
*-----------------------------------------------------------------------
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
#define CFG_TMCNTSC (TMCNTSC_SEC |\
TMCNTSC_ALR |\
TMCNTSC_TCF |\
TMCNTSC_TCE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 4-42
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
#ifdef CFG_EP8260_H2
#define CFG_PISCR (PISCR_PS |\
PISCR_PTF |\
PISCR_PTE)
#else
#define CFG_PISCR 0
#endif
/*-----------------------------------------------------------------------
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
*/
#define CFG_SCCR (SCCR_DFBRG01)
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
#define CFG_RCCR 0
/*-----------------------------------------------------------------------
* MPTPR - Memory Refresh Timer Prescale Register 10-32
*-----------------------------------------------------------------------
*/
#define CFG_MPTPR (0x0A00 & MPTPR_PTP_MSK)
/*
* Init Memory Controller:
*
* Bank Bus Machine PortSz Device
* ---- --- ------- ------ ------
* 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90WDI)
* 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Micron 48LC8M16A2TG)
* 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Micron 48LC8M16A2TG)
* 3 unused
* 4 60x GPCM 8 bit Board Regs, NVRTC
* 5 unused
* 6 unused
* 7 unused
* 8 PCMCIA
* 9 unused
* 10 unused
* 11 unused
*/
/*-----------------------------------------------------------------------
* BRx - Base Register
* Ref: Section 10.3.1 on page 10-14
* ORx - Option Register
* Ref: Section 10.3.2 on page 10-18
*-----------------------------------------------------------------------
*/
/* Bank 0 - FLASH
*
*/
#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_DECC_NONE |\
BRx_MS_GPCM_P |\
BRx_V)
#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_8_CLK |\
ORxG_EHTR)
/* Bank 1 - SDRAM
* PSDRAM
*/
#define CFG_BR1_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
#define CFG_OR1_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A6 |\
ORxS_NUMR_12)
#ifdef CFG_EP8260_H2
#define CFG_PSDMR 0xC34E246E
#else
#define CFG_PSDMR 0xC34E2462
#endif
#define CFG_PSRT 0x64
#ifdef CFG_LSDRAM
/* Bank 2 - SDRAM
* LSDRAM
*/
#define CFG_BR2_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_SDRAM_L |\
BRx_V)
#define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A9 |\
ORxS_NUMR_12)
#define CFG_LSDMR 0x416A2562
#define CFG_LSRT 0x64
#else
#define CFG_LSRT 0x0
#endif /* CFG_LSDRAM */
/* Bank 4 - On board registers
* NVRTC and BCSR
*/
#define CFG_BR4_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
/*
#define CFG_OR4_PRELIM (ORxG_AM_MSK |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_10_CLK |\
ORxG_TRLX)
*/
#define CFG_OR4_PRELIM 0xfff00854
#ifdef _NOT_USED_SINCE_NOT_WORKING_
/* Bank 8 - On board registers
* PCMCIA (currently not working!)
*/
#define CFG_BR8_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\
BRx_PS_16 |\
BRx_MS_GPCM_P |\
BRx_V)
#define CFG_OR8_PRELIM (ORxG_AM_MSK |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SETA |\
ORxG_SCY_10_CLK)
#endif
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition, whole device */
#undef CONFIG_JFFS2_CMDLINE
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT ""
#define MTDPARTS_DEFAULT ""
*/
#endif /* __CONFIG_H */