Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-18 10:48:51 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/arch/arm/mach-sunxi/dram_sun9i.c
Tom Rini 83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style 
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00

958 lines
30 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* sun9i dram controller initialisation
*
* (C) Copyright 2007-2015
* Allwinner Technology Co., Ltd. <www.allwinnertech.com>
* Jerry Wang <wangflord@allwinnertech.com>
*
* (C) Copyright 2016 Theobroma Systems Design und Consulting GmbH
* Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
*/
#include <common.h>
#include <dm.h>
#include <errno.h>
#include <ram.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/dram.h>
#include <asm/arch/sys_proto.h>
#define DRAM_CLK (CONFIG_DRAM_CLK * 1000000)
/*
* The following amounts to an extensive rewrite of the code received from
* Allwinner as part of the open-source bootloader release (refer to
* https://github.com/allwinner-zh/bootloader.git) and augments the upstream
* sources (which act as the primary reference point for the inner workings
* of the 'underdocumented' DRAM controller in the A80) using the following
* documentation for other memory controllers based on the (Synopsys)
* Designware IP (DDR memory protocol controller and DDR PHY)
* * TI Keystone II Architecture: DDR3 Memory Controller, User's Guide
* Document 'SPRUHN7C', Oct 2013 (revised March 2015)
* * Xilinx Zynq UltraScale+ MPSoC Register Reference
* document ug1087 (v1.0)
* Note that the Zynq-documentation provides a very close match for the DDR
* memory protocol controller (and provides a very good guide to the rounding
* rules for various timings), whereas the TI Keystone II document should be
* referred to for DDR PHY specifics only.
*
* The DRAM controller in the A80 runs at half the frequency of the DDR PHY
* (i.e. the rules for MEMC_FREQ_RATIO=2 from the Zynq-documentation apply).
*
* Known limitations
* =================
* In the current state, the following features are not fully supported and
* a number of simplifying assumptions have been made:
* 1) Only DDR3 support is implemented, as our test platform (the A80-Q7
* module) is designed to accomodate DDR3/DDR3L.
* 2) Only 2T-mode has been implemented and tested.
* 3) The controller supports two different clocking strategies (PLL6 can
* either be 2*CK or CK/2)... we only support the 2*CK clock at this
* time and haven't verified whether the alternative clocking strategy
* works. If you are interested in porting this over/testing this,
* please refer to cases where bit 0 of 'dram_tpr8' is tested in the
* original code from Allwinner.
* 4) Support for 2 ranks per controller is not implemented (as we don't
* the hardware to test it).
*
* Future directions
* =================
* The driver should be driven from a device-tree based configuration that
* can dynamically provide the necessary timing parameters (i.e. target
* frequency and speed-bin information)---the data structures used in the
* calculation of the timing parameters are already designed to capture
* similar information as the device tree would provide.
*
* To enable a device-tree based configuration of the sun9i platform, we
* will need to enable CONFIG_TPL and bootstrap in 3 stages: initially
* into SRAM A1 (40KB) and next into SRAM A2 (160KB)---which would be the
* stage to initialise the platform via the device-tree---before having
* the full U-Boot run from DDR.
*/
/*
* A number of DDR3 timings are given as "the greater of a fixed number of
* clock cycles (CK) or nanoseconds. We express these using a structure
* that holds a cycle count and a duration in picoseconds (so we can model
* sub-ns timings, such as 7.5ns without losing precision or resorting to
* rounding up early.
*/
struct dram_sun9i_timing {
u32 ck;
u32 ps;
};
/* */
struct dram_sun9i_cl_cwl_timing {
u32 CL;
u32 CWL;
u32 tCKmin; /* in ps */
u32 tCKmax; /* in ps */
};
struct dram_sun9i_para {
u32 dram_type;
u8 bus_width;
u8 chan;
u8 rank;
u8 rows;
u16 page_size;
/* Timing information for each speed-bin */
struct dram_sun9i_cl_cwl_timing *cl_cwl_table;
u32 cl_cwl_numentries;
/*
* For the timings, we try to keep the order and grouping used in
* JEDEC Standard No. 79-3F
*/
/* timings */
u32 tREFI; /* in ns */
u32 tRFC; /* in ns */
u32 tRAS; /* in ps */
/* command and address timing */
u32 tDLLK; /* in nCK */
struct dram_sun9i_timing tRTP;
struct dram_sun9i_timing tWTR;
u32 tWR; /* in nCK */
u32 tMRD; /* in nCK */
struct dram_sun9i_timing tMOD;
u32 tRCD; /* in ps */
u32 tRP; /* in ps */
u32 tRC; /* in ps */
u32 tCCD; /* in nCK */
struct dram_sun9i_timing tRRD;
u32 tFAW; /* in ps */
/* calibration timing */
/* struct dram_sun9i_timing tZQinit; */
struct dram_sun9i_timing tZQoper;
struct dram_sun9i_timing tZQCS;
/* reset timing */
/* struct dram_sun9i_timing tXPR; */
/* self-refresh timings */
struct dram_sun9i_timing tXS;
u32 tXSDLL; /* in nCK */
/* struct dram_sun9i_timing tCKESR; */
struct dram_sun9i_timing tCKSRE;
struct dram_sun9i_timing tCKSRX;
/* power-down timings */
struct dram_sun9i_timing tXP;
struct dram_sun9i_timing tXPDLL;
struct dram_sun9i_timing tCKE;
/* write leveling timings */
u32 tWLMRD; /* min, in nCK */
/* u32 tWLDQSEN; min, in nCK */
u32 tWLO; /* max, in ns */
/* u32 tWLOE; max, in ns */
/* u32 tCKDPX; in nCK */
/* u32 tCKCSX; in nCK */
};
static void mctl_sys_init(void);
#define SCHED_RDWR_IDLE_GAP(n) ((n & 0xff) << 24)
#define SCHED_GO2CRITICAL_HYSTERESIS(n) ((n & 0xff) << 16)
#define SCHED_LPR_NUM_ENTRIES(n) ((n & 0xff) << 8)
#define SCHED_PAGECLOSE (1 << 2)
#define SCHED_PREFER_WRITE (1 << 1)
#define SCHED_FORCE_LOW_PRI_N (1 << 0)
#define SCHED_CONFIG (SCHED_RDWR_IDLE_GAP(0xf) | \
SCHED_GO2CRITICAL_HYSTERESIS(0x80) | \
SCHED_LPR_NUM_ENTRIES(0x20) | \
SCHED_FORCE_LOW_PRI_N)
#define PERFHPR0_CONFIG 0x0000001f
#define PERFHPR1_CONFIG 0x1f00001f
#define PERFLPR0_CONFIG 0x000000ff
#define PERFLPR1_CONFIG 0x0f0000ff
#define PERFWR0_CONFIG 0x000000ff
#define PERFWR1_CONFIG 0x0f0001ff
static void mctl_ctl_sched_init(unsigned long base)
{
struct sunxi_mctl_ctl_reg *mctl_ctl =
(struct sunxi_mctl_ctl_reg *)base;
/* Needs to be done before the global clk enable... */
writel(SCHED_CONFIG, &mctl_ctl->sched);
writel(PERFHPR0_CONFIG, &mctl_ctl->perfhpr0);
writel(PERFHPR1_CONFIG, &mctl_ctl->perfhpr1);
writel(PERFLPR0_CONFIG, &mctl_ctl->perflpr0);
writel(PERFLPR1_CONFIG, &mctl_ctl->perflpr1);
writel(PERFWR0_CONFIG, &mctl_ctl->perfwr0);
writel(PERFWR1_CONFIG, &mctl_ctl->perfwr1);
}
static void mctl_sys_init(void)
{
struct sunxi_ccm_reg * const ccm =
(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
struct sunxi_mctl_com_reg * const mctl_com =
(struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
debug("Setting PLL6 to %d\n", DRAM_CLK * 2);
clock_set_pll6(DRAM_CLK * 2);
/* Original dram init code which may come in handy later
********************************************************
clock_set_pll6(use_2channelPLL ? (DRAM_CLK * 2) :
(DRAM_CLK / 2), false);
if ((para->dram_clk <= 400)|((para->dram_tpr8 & 0x1)==0)) {
* PLL6 should be 2*CK *
* ccm_setup_pll6_ddr_clk(PLL6_DDR_CLK); *
ccm_setup_pll6_ddr_clk((1000000 * (para->dram_clk) * 2), 0);
} else {
* PLL6 should be CK/2 *
ccm_setup_pll6_ddr_clk((1000000 * (para->dram_clk) / 2), 1);
}
if (para->dram_tpr13 & (0xf<<18)) {
*
* bit21:bit18=0001:pll swing 0.4
* bit21:bit18=0010:pll swing 0.3
* bit21:bit18=0100:pll swing 0.2
* bit21:bit18=1000:pll swing 0.1
*
dram_dbg("DRAM fre extend open !\n");
reg_val=mctl_read_w(CCM_PLL6_DDR_REG);
reg_val&=(0x1<<16);
reg_val=reg_val>>16;
if(para->dram_tpr13 & (0x1<<18))
{
mctl_write_w(CCM_PLL_BASE + 0x114,
(0x3333U|(0x3<<17)|(reg_val<<19)|(0x120U<<20)|
(0x2U<<29)|(0x1U<<31)));
}
else if(para->dram_tpr13 & (0x1<<19))
{
mctl_write_w(CCM_PLL_BASE + 0x114,
(0x6666U|(0x3U<<17)|(reg_val<<19)|(0xD8U<<20)|
(0x2U<<29)|(0x1U<<31)));
}
else if(para->dram_tpr13 & (0x1<<20))
{
mctl_write_w(CCM_PLL_BASE + 0x114,
(0x9999U|(0x3U<<17)|(reg_val<<19)|(0x90U<<20)|
(0x2U<<29)|(0x1U<<31)));
}
else if(para->dram_tpr13 & (0x1<<21))
{
mctl_write_w(CCM_PLL_BASE + 0x114,
(0xccccU|(0x3U<<17)|(reg_val<<19)|(0x48U<<20)|
(0x2U<<29)|(0x1U<<31)));
}
//frequency extend open
reg_val = mctl_read_w(CCM_PLL6_DDR_REG);
reg_val |= ((0x1<<24)|(0x1<<30));
mctl_write_w(CCM_PLL6_DDR_REG, reg_val);
while(mctl_read_w(CCM_PLL6_DDR_REG) & (0x1<<30));
}
aw_delay(0x20000); //make some delay
********************************************************
*/
/* assert mctl reset */
clrbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
/* stop mctl clock */
clrbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
sdelay(2000);
/* deassert mctl reset */
setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MCTL);
/* enable mctl clock */
setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MCTL);
/* set up the transactions scheduling before enabling the global clk */
mctl_ctl_sched_init(SUNXI_DRAM_CTL0_BASE);
mctl_ctl_sched_init(SUNXI_DRAM_CTL1_BASE);
sdelay(1000);
debug("2\n");
/* (3 << 12): PLL_DDR */
writel((3 << 12) | (1 << 16), &ccm->dram_clk_cfg);
do {
debug("Waiting for DRAM_CLK_CFG\n");
sdelay(10000);
} while (readl(&ccm->dram_clk_cfg) & (1 << 16));
setbits_le32(&ccm->dram_clk_cfg, (1 << 31));
/* TODO: we only support the common case ... i.e. 2*CK */
setbits_le32(&mctl_com->ccr, (1 << 14) | (1 << 30));
writel(2, &mctl_com->rmcr); /* controller clock is PLL6/4 */
sdelay(2000);
/* Original dram init code which may come in handy later
********************************************************
if ((para->dram_clk <= 400) | ((para->dram_tpr8 & 0x1) == 0)) {
* PLL6 should be 2*CK *
* gating 2 channel pll *
reg_val = mctl_read_w(MC_CCR);
reg_val |= ((0x1 << 14) | (0x1U << 30));
mctl_write_w(MC_CCR, reg_val);
mctl_write_w(MC_RMCR, 0x2); * controller clock use pll6/4 *
} else {
* enable 2 channel pll *
reg_val = mctl_read_w(MC_CCR);
reg_val &= ~((0x1 << 14) | (0x1U << 30));
mctl_write_w(MC_CCR, reg_val);
mctl_write_w(MC_RMCR, 0x0); * controller clock use pll6 *
}
reg_val = mctl_read_w(MC_CCR);
reg_val &= ~((0x1<<15)|(0x1U<<31));
mctl_write_w(MC_CCR, reg_val);
aw_delay(20);
//aw_delay(0x10);
********************************************************
*/
clrbits_le32(&mctl_com->ccr, MCTL_CCR_CH0_CLK_EN | MCTL_CCR_CH1_CLK_EN);
sdelay(1000);
setbits_le32(&mctl_com->ccr, MCTL_CCR_CH0_CLK_EN);
/* TODO if (para->chan == 2) */
setbits_le32(&mctl_com->ccr, MCTL_CCR_CH1_CLK_EN);
}
static void mctl_com_init(struct dram_sun9i_para *para)
{
struct sunxi_mctl_com_reg * const mctl_com =
(struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
/* TODO: hard-wired for DDR3 now */
writel(((para->chan == 2) ? MCTL_CR_CHANNEL_DUAL :
MCTL_CR_CHANNEL_SINGLE)
| MCTL_CR_DRAMTYPE_DDR3 | MCTL_CR_BANK(1)
| MCTL_CR_ROW(para->rows)
| ((para->bus_width == 32) ? MCTL_CR_BUSW32 : MCTL_CR_BUSW16)
| MCTL_CR_PAGE_SIZE(para->page_size) | MCTL_CR_RANK(para->rank),
&mctl_com->cr);
debug("CR: %d\n", readl(&mctl_com->cr));
}
static u32 mctl_channel_init(u32 ch_index, struct dram_sun9i_para *para)
{
struct sunxi_mctl_ctl_reg *mctl_ctl;
struct sunxi_mctl_phy_reg *mctl_phy;
u32 CL = 0;
u32 CWL = 0;
u16 mr[4] = { 0, };
#define PS2CYCLES_FLOOR(n) ((n * CONFIG_DRAM_CLK) / 1000000)
#define PS2CYCLES_ROUNDUP(n) ((n * CONFIG_DRAM_CLK + 999999) / 1000000)
#define NS2CYCLES_FLOOR(n) ((n * CONFIG_DRAM_CLK) / 1000)
#define NS2CYCLES_ROUNDUP(n) ((n * CONFIG_DRAM_CLK + 999) / 1000)
#define MAX(a, b) ((a) > (b) ? (a) : (b))
/*
* Convert the values to cycle counts (nCK) from what is provided
* by the definition of each speed bin.
*/
/* const u32 tREFI = NS2CYCLES_FLOOR(para->tREFI); */
const u32 tREFI = NS2CYCLES_FLOOR(para->tREFI);
const u32 tRFC = NS2CYCLES_ROUNDUP(para->tRFC);
const u32 tRCD = PS2CYCLES_ROUNDUP(para->tRCD);
const u32 tRP = PS2CYCLES_ROUNDUP(para->tRP);
const u32 tRC = PS2CYCLES_ROUNDUP(para->tRC);
const u32 tRAS = PS2CYCLES_ROUNDUP(para->tRAS);
/* command and address timing */
const u32 tDLLK = para->tDLLK;
const u32 tRTP = MAX(para->tRTP.ck, PS2CYCLES_ROUNDUP(para->tRTP.ps));
const u32 tWTR = MAX(para->tWTR.ck, PS2CYCLES_ROUNDUP(para->tWTR.ps));
const u32 tWR = NS2CYCLES_FLOOR(para->tWR);
const u32 tMRD = para->tMRD;
const u32 tMOD = MAX(para->tMOD.ck, PS2CYCLES_ROUNDUP(para->tMOD.ps));
const u32 tCCD = para->tCCD;
const u32 tRRD = MAX(para->tRRD.ck, PS2CYCLES_ROUNDUP(para->tRRD.ps));
const u32 tFAW = PS2CYCLES_ROUNDUP(para->tFAW);
/* calibration timings */
/* const u32 tZQinit = MAX(para->tZQinit.ck,
PS2CYCLES_ROUNDUP(para->tZQinit.ps)); */
const u32 tZQoper = MAX(para->tZQoper.ck,
PS2CYCLES_ROUNDUP(para->tZQoper.ps));
const u32 tZQCS = MAX(para->tZQCS.ck,
PS2CYCLES_ROUNDUP(para->tZQCS.ps));
/* reset timing */
/* const u32 tXPR = MAX(para->tXPR.ck,
PS2CYCLES_ROUNDUP(para->tXPR.ps)); */
/* power-down timings */
const u32 tXP = MAX(para->tXP.ck, PS2CYCLES_ROUNDUP(para->tXP.ps));
const u32 tXPDLL = MAX(para->tXPDLL.ck,
PS2CYCLES_ROUNDUP(para->tXPDLL.ps));
const u32 tCKE = MAX(para->tCKE.ck, PS2CYCLES_ROUNDUP(para->tCKE.ps));
/*
* self-refresh timings (keep below power-down timings, as tCKESR
* needs to be calculated based on the nCK value of tCKE)
*/
const u32 tXS = MAX(para->tXS.ck, PS2CYCLES_ROUNDUP(para->tXS.ps));
const u32 tXSDLL = para->tXSDLL;
const u32 tCKSRE = MAX(para->tCKSRE.ck,
PS2CYCLES_ROUNDUP(para->tCKSRE.ps));
const u32 tCKESR = tCKE + 1;
const u32 tCKSRX = MAX(para->tCKSRX.ck,
PS2CYCLES_ROUNDUP(para->tCKSRX.ps));
/* write leveling timings */
const u32 tWLMRD = para->tWLMRD;
/* const u32 tWLDQSEN = para->tWLDQSEN; */
const u32 tWLO = PS2CYCLES_FLOOR(para->tWLO);
/* const u32 tWLOE = PS2CYCLES_FLOOR(para->tWLOE); */
const u32 tRASmax = tREFI * 9;
int i;
for (i = 0; i < para->cl_cwl_numentries; ++i) {
const u32 tCK = 1000000 / CONFIG_DRAM_CLK;
if ((para->cl_cwl_table[i].tCKmin <= tCK) &&
(tCK < para->cl_cwl_table[i].tCKmax)) {
CL = para->cl_cwl_table[i].CL;
CWL = para->cl_cwl_table[i].CWL;
debug("found CL/CWL: CL = %d, CWL = %d\n", CL, CWL);
break;
}
}
if ((CL == 0) && (CWL == 0)) {
printf("failed to find valid CL/CWL for operating point %d MHz\n",
CONFIG_DRAM_CLK);
return 0;
}
if (ch_index == 0) {
mctl_ctl = (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
mctl_phy = (struct sunxi_mctl_phy_reg *)SUNXI_DRAM_PHY0_BASE;
} else {
mctl_ctl = (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL1_BASE;
mctl_phy = (struct sunxi_mctl_phy_reg *)SUNXI_DRAM_PHY1_BASE;
}
if (para->dram_type == DRAM_TYPE_DDR3) {
mr[0] = DDR3_MR0_PPD_FAST_EXIT | DDR3_MR0_WR(tWR) |
DDR3_MR0_CL(CL);
mr[1] = DDR3_MR1_RTT120OHM;
mr[2] = DDR3_MR2_TWL(CWL);
mr[3] = 0;
/*
* DRAM3 initialisation requires holding CKE LOW for
* at least 500us prior to starting the initialisation
* sequence and at least 10ns after driving CKE HIGH
* before the initialisation sequence may be started).
*
* Refer to Micron document "TN-41-07: DDR3 Power-Up,
* Initialization, and Reset DDR3 Initialization
* Routine" for details).
*/
writel(MCTL_INIT0_POST_CKE_x1024(1) |
MCTL_INIT0_PRE_CKE_x1024(
(500 * CONFIG_DRAM_CLK + 1023) / 1024), /* 500us */
&mctl_ctl->init[0]);
writel(MCTL_INIT1_DRAM_RSTN_x1024(1),
&mctl_ctl->init[1]);
/* INIT2 is not used for DDR3 */
writel(MCTL_INIT3_MR(mr[0]) | MCTL_INIT3_EMR(mr[1]),
&mctl_ctl->init[3]);
writel(MCTL_INIT4_EMR2(mr[2]) | MCTL_INIT4_EMR3(mr[3]),
&mctl_ctl->init[4]);
writel(MCTL_INIT5_DEV_ZQINIT_x32(512 / 32), /* 512 cycles */
&mctl_ctl->init[5]);
} else {
/* !!! UNTESTED !!! */
/*
* LPDDR2 and/or LPDDR3 require a 200us minimum delay
* after driving CKE HIGH in the initialisation sequence.
*/
writel(MCTL_INIT0_POST_CKE_x1024(
(200 * CONFIG_DRAM_CLK + 1023) / 1024),
&mctl_ctl->init[0]);
writel(MCTL_INIT1_DRAM_RSTN_x1024(1),
&mctl_ctl->init[1]);
writel(MCTL_INIT2_IDLE_AFTER_RESET_x32(
(CONFIG_DRAM_CLK + 31) / 32) /* 1us */
| MCTL_INIT2_MIN_STABLE_CLOCK_x1(5), /* 5 cycles */
&mctl_ctl->init[2]);
writel(MCTL_INIT3_MR(mr[1]) | MCTL_INIT3_EMR(mr[2]),
&mctl_ctl->init[3]);
writel(MCTL_INIT4_EMR2(mr[3]),
&mctl_ctl->init[4]);
writel(MCTL_INIT5_DEV_ZQINIT_x32(
(CONFIG_DRAM_CLK + 31) / 32) /* 1us */
| MCTL_INIT5_MAX_AUTO_INIT_x1024(
(10 * CONFIG_DRAM_CLK + 1023) / 1024),
&mctl_ctl->init[5]);
}
/* (DDR3) We always use a burst-length of 8. */
#define MCTL_BL 8
/* wr2pre: WL + BL/2 + tWR */
#define WR2PRE (MCTL_BL/2 + CWL + tWTR)
/* wr2rd = CWL + BL/2 + tWTR */
#define WR2RD (MCTL_BL/2 + CWL + tWTR)
/*
* rd2wr = RL + BL/2 + 2 - WL (for DDR3)
* rd2wr = RL + BL/2 + RU(tDQSCKmax/tCK) + 1 - WL (for LPDDR2/LPDDR3)
*/
#define RD2WR (CL + MCTL_BL/2 + 2 - CWL)
#define MCTL_PHY_TRTW 0
#define MCTL_PHY_TRTODT 0
#define MCTL_DIV2(n) ((n + 1)/2)
#define MCTL_DIV32(n) (n/32)
#define MCTL_DIV1024(n) (n/1024)
writel((MCTL_DIV2(WR2PRE) << 24) | (MCTL_DIV2(tFAW) << 16) |
(MCTL_DIV1024(tRASmax) << 8) | (MCTL_DIV2(tRAS) << 0),
&mctl_ctl->dramtmg[0]);
writel((MCTL_DIV2(tXP) << 16) | (MCTL_DIV2(tRTP) << 8) |
(MCTL_DIV2(tRC) << 0),
&mctl_ctl->dramtmg[1]);
writel((MCTL_DIV2(CWL) << 24) | (MCTL_DIV2(CL) << 16) |
(MCTL_DIV2(RD2WR) << 8) | (MCTL_DIV2(WR2RD) << 0),
&mctl_ctl->dramtmg[2]);
/*
* Note: tMRW is located at bit 16 (and up) in DRAMTMG3...
* this is only relevant for LPDDR2/LPDDR3
*/
writel((MCTL_DIV2(tMRD) << 12) | (MCTL_DIV2(tMOD) << 0),
&mctl_ctl->dramtmg[3]);
writel((MCTL_DIV2(tRCD) << 24) | (MCTL_DIV2(tCCD) << 16) |
(MCTL_DIV2(tRRD) << 8) | (MCTL_DIV2(tRP) << 0),
&mctl_ctl->dramtmg[4]);
writel((MCTL_DIV2(tCKSRX) << 24) | (MCTL_DIV2(tCKSRE) << 16) |
(MCTL_DIV2(tCKESR) << 8) | (MCTL_DIV2(tCKE) << 0),
&mctl_ctl->dramtmg[5]);
/* These timings are relevant for LPDDR2/LPDDR3 only */
/* writel((MCTL_TCKDPDE << 24) | (MCTL_TCKDPX << 16) |
(MCTL_TCKCSX << 0), &mctl_ctl->dramtmg[6]); */
/* printf("DRAMTMG7 reset value: 0x%x\n",
readl(&mctl_ctl->dramtmg[7])); */
/* DRAMTMG7 reset value: 0x202 */
/* DRAMTMG7 should contain t_ckpde and t_ckpdx: check reset values!!! */
/* printf("DRAMTMG8 reset value: 0x%x\n",
readl(&mctl_ctl->dramtmg[8])); */
/* DRAMTMG8 reset value: 0x44 */
writel((MCTL_DIV32(tXSDLL) << 0), &mctl_ctl->dramtmg[8]);
writel((MCTL_DIV32(tREFI) << 16) | (MCTL_DIV2(tRFC) << 0),
&mctl_ctl->rfshtmg);
if (para->dram_type == DRAM_TYPE_DDR3) {
writel((2 << 24) | ((MCTL_DIV2(CL) - 2) << 16) |
(1 << 8) | ((MCTL_DIV2(CWL) - 2) << 0),
&mctl_ctl->dfitmg[0]);
} else {
/* TODO */
}
/* TODO: handle the case of the write latency domain going to 0 ... */
/*
* Disable dfi_init_complete_en (the triggering of the SDRAM
* initialisation when the PHY initialisation completes).
*/
clrbits_le32(&mctl_ctl->dfimisc, MCTL_DFIMISC_DFI_INIT_COMPLETE_EN);
/* Disable the automatic generation of DLL calibration requests */
setbits_le32(&mctl_ctl->dfiupd[0], MCTL_DFIUPD0_DIS_AUTO_CTRLUPD);
/* A80-Q7: 2T, 1 rank, DDR3, full-32bit-DQ */
/* TODO: make 2T and BUSWIDTH configurable */
writel(MCTL_MSTR_DEVICETYPE(para->dram_type) |
MCTL_MSTR_BURSTLENGTH(para->dram_type) |
MCTL_MSTR_ACTIVERANKS(para->rank) |
MCTL_MSTR_2TMODE | MCTL_MSTR_BUSWIDTH32,
&mctl_ctl->mstr);
if (para->dram_type == DRAM_TYPE_DDR3) {
writel(MCTL_ZQCTRL0_TZQCL(MCTL_DIV2(tZQoper)) |
(MCTL_DIV2(tZQCS)), &mctl_ctl->zqctrl[0]);
/*
* TODO: is the following really necessary as the bottom
* half should already be 0x100 and the upper half should
* be ignored for a DDR3 device???
*/
writel(MCTL_ZQCTRL1_TZQSI_x1024(0x100),
&mctl_ctl->zqctrl[1]);
} else {
writel(MCTL_ZQCTRL0_TZQCL(0x200) | MCTL_ZQCTRL0_TZQCS(0x40),
&mctl_ctl->zqctrl[0]);
writel(MCTL_ZQCTRL1_TZQRESET(0x28) |
MCTL_ZQCTRL1_TZQSI_x1024(0x100),
&mctl_ctl->zqctrl[1]);
}
/* Assert dfi_init_complete signal */
setbits_le32(&mctl_ctl->dfimisc, MCTL_DFIMISC_DFI_INIT_COMPLETE_EN);
/* Disable auto-refresh */
setbits_le32(&mctl_ctl->rfshctl3, MCTL_RFSHCTL3_DIS_AUTO_REFRESH);
/* PHY initialisation */
/* TODO: make 2T and 8-bank mode configurable */
writel(MCTL_PHY_DCR_BYTEMASK | MCTL_PHY_DCR_2TMODE |
MCTL_PHY_DCR_DDR8BNK | MCTL_PHY_DRAMMODE_DDR3,
&mctl_phy->dcr);
/* For LPDDR2 or LPDDR3, set DQSGX to 0 before training. */
if (para->dram_type != DRAM_TYPE_DDR3)
clrbits_le32(&mctl_phy->dsgcr, (3 << 6));
writel(mr[0], &mctl_phy->mr0);
writel(mr[1], &mctl_phy->mr1);
writel(mr[2], &mctl_phy->mr2);
writel(mr[3], &mctl_phy->mr3);
/*
* The DFI PHY is running at full rate. We thus use the actual
* timings in clock cycles here.
*/
writel((tRC << 26) | (tRRD << 22) | (tRAS << 16) |
(tRCD << 12) | (tRP << 8) | (tWTR << 4) | (tRTP << 0),
&mctl_phy->dtpr[0]);
writel((tMRD << 0) | ((tMOD - 12) << 2) | (tFAW << 5) |
(tRFC << 11) | (tWLMRD << 20) | (tWLO << 26),
&mctl_phy->dtpr[1]);
writel((tXS << 0) | (MAX(tXP, tXPDLL) << 10) |
(tCKE << 15) | (tDLLK << 19) |
(MCTL_PHY_TRTODT << 29) | (MCTL_PHY_TRTW << 30) |
(((tCCD - 4) & 0x1) << 31),
&mctl_phy->dtpr[2]);
/* tDQSCK and tDQSCKmax are used LPDDR2/LPDDR3 */
/* writel((tDQSCK << 0) | (tDQSCKMAX << 3), &mctl_phy->dtpr[3]); */
/*
* We use the same values used by Allwinner's Boot0 for the PTR
* (PHY timing register) configuration that is tied to the PHY
* implementation.
*/
writel(0x42C21590, &mctl_phy->ptr[0]);
writel(0xD05612C0, &mctl_phy->ptr[1]);
if (para->dram_type == DRAM_TYPE_DDR3) {
const unsigned int tdinit0 = 500 * CONFIG_DRAM_CLK; /* 500us */
const unsigned int tdinit1 = (360 * CONFIG_DRAM_CLK + 999) /
1000; /* 360ns */
const unsigned int tdinit2 = 200 * CONFIG_DRAM_CLK; /* 200us */
const unsigned int tdinit3 = CONFIG_DRAM_CLK; /* 1us */
writel((tdinit1 << 20) | tdinit0, &mctl_phy->ptr[3]);
writel((tdinit3 << 18) | tdinit2, &mctl_phy->ptr[4]);
} else {
/* LPDDR2 or LPDDR3 */
const unsigned int tdinit0 = (100 * CONFIG_DRAM_CLK + 999) /
1000; /* 100ns */
const unsigned int tdinit1 = 200 * CONFIG_DRAM_CLK; /* 200us */
const unsigned int tdinit2 = 22 * CONFIG_DRAM_CLK; /* 11us */
const unsigned int tdinit3 = 2 * CONFIG_DRAM_CLK; /* 2us */
writel((tdinit1 << 20) | tdinit0, &mctl_phy->ptr[3]);
writel((tdinit3 << 18) | tdinit2, &mctl_phy->ptr[4]);
}
/* TEST ME */
writel(0x00203131, &mctl_phy->acmdlr);
/* TODO: can we enable this for 2 ranks, even when we don't know yet */
writel(MCTL_DTCR_DEFAULT | MCTL_DTCR_RANKEN(para->rank),
&mctl_phy->dtcr);
/* TODO: half width */
debug("DX2GCR0 reset: 0x%x\n", readl(&mctl_phy->dx[2].gcr[0]));
writel(0x7C000285, &mctl_phy->dx[2].gcr[0]);
writel(0x7C000285, &mctl_phy->dx[3].gcr[0]);
clrsetbits_le32(&mctl_phy->zq[0].pr, 0xff,
(CONFIG_DRAM_ZQ >> 0) & 0xff); /* CK/CA */
clrsetbits_le32(&mctl_phy->zq[1].pr, 0xff,
(CONFIG_DRAM_ZQ >> 8) & 0xff); /* DX0/DX1 */
clrsetbits_le32(&mctl_phy->zq[2].pr, 0xff,
(CONFIG_DRAM_ZQ >> 16) & 0xff); /* DX2/DX3 */
/* TODO: make configurable & implement non-ODT path */
if (1) {
int lane;
for (lane = 0; lane < 4; ++lane) {
clrbits_le32(&mctl_phy->dx[lane].gcr[2], 0xffff);
clrbits_le32(&mctl_phy->dx[lane].gcr[3],
(0x3<<12) | (0x3<<4));
}
} else {
/* TODO: check */
int lane;
for (lane = 0; lane < 4; ++lane) {
clrsetbits_le32(&mctl_phy->dx[lane].gcr[2], 0xffff,
0xaaaa);
if (para->dram_type == DRAM_TYPE_DDR3)
setbits_le32(&mctl_phy->dx[lane].gcr[3],
(0x3<<12) | (0x3<<4));
else
setbits_le32(&mctl_phy->dx[lane].gcr[3],
0x00000012);
}
}
writel(0x04058D02, &mctl_phy->zq[0].cr); /* CK/CA */
writel(0x04058D02, &mctl_phy->zq[1].cr); /* DX0/DX1 */
writel(0x04058D02, &mctl_phy->zq[2].cr); /* DX2/DX3 */
/* Disable auto-refresh prior to data training */
setbits_le32(&mctl_ctl->rfshctl3, MCTL_RFSHCTL3_DIS_AUTO_REFRESH);
setbits_le32(&mctl_phy->dsgcr, 0xf << 24); /* unclear what this is... */
/* TODO: IODDRM (IO DDR-MODE) for DDR3L */
clrsetbits_le32(&mctl_phy->pgcr[1],
MCTL_PGCR1_ZCKSEL_MASK,
MCTL_PGCR1_IODDRM_DDR3 | MCTL_PGCR1_INHVT_EN);
setbits_le32(&mctl_phy->pllcr, 0x3 << 19); /* PLL frequency select */
/* TODO: single-channel PLL mode??? missing */
setbits_le32(&mctl_phy->pllcr,
MCTL_PLLGCR_PLL_BYPASS | MCTL_PLLGCR_PLL_POWERDOWN);
/* setbits_le32(&mctl_phy->pir, MCTL_PIR_PLL_BYPASS); included below */
/* Disable VT compensation */
clrbits_le32(&mctl_phy->pgcr[0], 0x3f);
/* TODO: "other" PLL mode ... 0x20000 seems to be the PLL Bypass */
if (para->dram_type == DRAM_TYPE_DDR3)
clrsetbits_le32(&mctl_phy->pir, MCTL_PIR_MASK, 0x20df3);
else
clrsetbits_le32(&mctl_phy->pir, MCTL_PIR_MASK, 0x2c573);
sdelay(10000); /* XXX necessary? */
/* Wait for the INIT bit to clear itself... */
while ((readl(&mctl_phy->pir) & MCTL_PIR_INIT) != MCTL_PIR_INIT) {
/* not done yet -- keep spinning */
debug("MCTL_PIR_INIT not set\n");
sdelay(1000);
/* TODO: implement timeout */
}
/* TODO: not used --- there's a "2rank debug" section here */
/* Original dram init code which may come in handy later
********************************************************
* LPDDR2 and LPDDR3 *
if ((para->dram_type) == 6 || (para->dram_type) == 7) {
reg_val = mctl_read_w(P0_DSGCR + ch_offset);
reg_val &= (~(0x3<<6)); * set DQSGX to 1 *
reg_val |= (0x1<<6); * dqs gate extend *
mctl_write_w(P0_DSGCR + ch_offset, reg_val);
dram_dbg("DQS Gate Extend Enable!\n", ch_index);
}
* Disable ZCAL after initial--for nand dma debug--20140330 by YSZ *
if (para->dram_tpr13 & (0x1<<31)) {
reg_val = mctl_read_w(P0_ZQ0CR + ch_offset);
reg_val |= (0x7<<11);
mctl_write_w(P0_ZQ0CR + ch_offset, reg_val);
}
********************************************************
*/
/*
* TODO: more 2-rank support
* (setting the "dqs gate delay to average between 2 rank")
*/
/* check if any errors are set */
if (readl(&mctl_phy->pgsr[0]) & MCTL_PGSR0_ERRORS) {
debug("Channel %d unavailable!\n", ch_index);
return 0;
} else{
/* initial OK */
debug("Channel %d OK!\n", ch_index);
/* return 1; */
}
while ((readl(&mctl_ctl->stat) & 0x1) != 0x1) {
debug("Waiting for INIT to be done (controller to come up into 'normal operating' mode\n");
sdelay(100000);
/* init not done */
/* TODO: implement time-out */
}
debug("done\n");
/* "DDR is controller by contoller" */
clrbits_le32(&mctl_phy->pgcr[3], (1 << 25));
/* TODO: is the following necessary? */
debug("DFIMISC before writing 0: 0x%x\n", readl(&mctl_ctl->dfimisc));
writel(0, &mctl_ctl->dfimisc);
/* Enable auto-refresh */
clrbits_le32(&mctl_ctl->rfshctl3, MCTL_RFSHCTL3_DIS_AUTO_REFRESH);
debug("channel_init complete\n");
return 1;
}
signed int DRAMC_get_dram_size(void)
{
struct sunxi_mctl_com_reg * const mctl_com =
(struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
unsigned int reg_val;
unsigned int dram_size;
unsigned int temp;
reg_val = readl(&mctl_com->cr);
temp = (reg_val >> 8) & 0xf; /* page size code */
dram_size = (temp - 6); /* (1 << dram_size) * 512Bytes */
temp = (reg_val >> 4) & 0xf; /* row width code */
dram_size += (temp + 1); /* (1 << dram_size) * 512Bytes */
temp = (reg_val >> 2) & 0x3; /* bank number code */
dram_size += (temp + 2); /* (1 << dram_size) * 512Bytes */
temp = reg_val & 0x3; /* rank number code */
dram_size += temp; /* (1 << dram_size) * 512Bytes */
temp = (reg_val >> 19) & 0x1; /* channel number code */
dram_size += temp; /* (1 << dram_size) * 512Bytes */
dram_size = dram_size - 11; /* (1 << dram_size) MBytes */
return 1 << dram_size;
}
unsigned long sunxi_dram_init(void)
{
struct sunxi_mctl_com_reg * const mctl_com =
(struct sunxi_mctl_com_reg *)SUNXI_DRAM_COM_BASE;
struct dram_sun9i_cl_cwl_timing cl_cwl[] = {
{ .CL = 5, .CWL = 5, .tCKmin = 3000, .tCKmax = 3300 },
{ .CL = 6, .CWL = 5, .tCKmin = 2500, .tCKmax = 3300 },
{ .CL = 8, .CWL = 6, .tCKmin = 1875, .tCKmax = 2500 },
{ .CL = 10, .CWL = 7, .tCKmin = 1500, .tCKmax = 1875 },
{ .CL = 11, .CWL = 8, .tCKmin = 1250, .tCKmax = 1500 }
};
/* Set initial parameters, these get modified by the autodetect code */
struct dram_sun9i_para para = {
.dram_type = DRAM_TYPE_DDR3,
.bus_width = 32,
.chan = 2,
.rank = 1,
/* .rank = 2, */
.page_size = 4096,
/* .rows = 16, */
.rows = 15,
/* CL/CWL table for the speed bin */
.cl_cwl_table = cl_cwl,
.cl_cwl_numentries = sizeof(cl_cwl) /
sizeof(struct dram_sun9i_cl_cwl_timing),
/* timings */
.tREFI = 7800, /* 7.8us (up to 85 degC) */
.tRFC = 260, /* 260ns for 4GBit devices */
/* 350ns @ 8GBit */
.tRCD = 13750,
.tRP = 13750,
.tRC = 48750,
.tRAS = 35000,
.tDLLK = 512,
.tRTP = { .ck = 4, .ps = 7500 },
.tWTR = { .ck = 4, .ps = 7500 },
.tWR = 15,
.tMRD = 4,
.tMOD = { .ck = 12, .ps = 15000 },
.tCCD = 4,
.tRRD = { .ck = 4, .ps = 7500 },
.tFAW = 40,
/* calibration timing */
/* .tZQinit = { .ck = 512, .ps = 640000 }, */
.tZQoper = { .ck = 256, .ps = 320000 },
.tZQCS = { .ck = 64, .ps = 80000 },
/* reset timing */
/* .tXPR = { .ck = 5, .ps = 10000 }, */
/* self-refresh timings */
.tXS = { .ck = 5, .ps = 10000 },
.tXSDLL = 512,
.tCKSRE = { .ck = 5, .ps = 10000 },
.tCKSRX = { .ck = 5, .ps = 10000 },
/* power-down timings */
.tXP = { .ck = 3, .ps = 6000 },
.tXPDLL = { .ck = 10, .ps = 24000 },
.tCKE = { .ck = 3, .ps = 5000 },
/* write leveling timings */
.tWLMRD = 40,
/* .tWLDQSEN = 25, */
.tWLO = 7500,
/* .tWLOE = 2000, */
};
/*
* Disable A80 internal 240 ohm resistor.
*
* This code sequence is adapated from Allwinner's Boot0 (see
* https://github.com/allwinner-zh/bootloader.git), as there
* is no documentation for these two registers in the R_PRCM
* block.
*/
setbits_le32(SUNXI_PRCM_BASE + 0x1e0, (0x3 << 8));
writel(0, SUNXI_PRCM_BASE + 0x1e8);
mctl_sys_init();
if (!mctl_channel_init(0, &para))
return 0;
/* dual-channel */
if (!mctl_channel_init(1, &para)) {
/* disable channel 1 */
clrsetbits_le32(&mctl_com->cr, MCTL_CR_CHANNEL_MASK,
MCTL_CR_CHANNEL_SINGLE);
/* disable channel 1 global clock */
clrbits_le32(&mctl_com->cr, MCTL_CCR_CH1_CLK_EN);
}
mctl_com_init(&para);
/* return the proper RAM size */
return DRAMC_get_dram_size() << 20;
}
Reference in a new issue View git blame Copy permalink