mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-12 07:57:21 +00:00
b7c4d25d26
This is needed when booting Linux without ARM Trusted Firmware. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
105 lines
2.6 KiB
Text
105 lines
2.6 KiB
Text
if ARCH_UNIPHIER
|
|
|
|
config SYS_CONFIG_NAME
|
|
default "uniphier"
|
|
|
|
config ARCH_UNIPHIER_32BIT
|
|
bool
|
|
select CPU_V7
|
|
|
|
config ARCH_UNIPHIER_64BIT
|
|
bool
|
|
select ARM64
|
|
select SPL_SEPARATE_BSS
|
|
select ARMV8_MULTIENTRY
|
|
select ARMV8_SPIN_TABLE
|
|
|
|
choice
|
|
prompt "UniPhier SoC select"
|
|
default ARCH_UNIPHIER_PRO4
|
|
|
|
config ARCH_UNIPHIER_SLD3
|
|
bool "UniPhier PH1-sLD3 SoC"
|
|
select ARCH_UNIPHIER_32BIT
|
|
|
|
config ARCH_UNIPHIER_LD4_SLD8
|
|
bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
|
|
select ARCH_UNIPHIER_32BIT
|
|
|
|
config ARCH_UNIPHIER_PRO4
|
|
bool "UniPhier PH1-Pro4 SoC"
|
|
select ARCH_UNIPHIER_32BIT
|
|
|
|
config ARCH_UNIPHIER_PRO5_PXS2_LD6B
|
|
bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
|
|
select ARCH_UNIPHIER_32BIT
|
|
|
|
config ARCH_UNIPHIER_LD11
|
|
bool "UniPhier PH1-LD11 SoC"
|
|
select ARCH_UNIPHIER_64BIT
|
|
|
|
config ARCH_UNIPHIER_LD20
|
|
bool "UniPhier PH1-LD20 SoC"
|
|
select ARCH_UNIPHIER_64BIT
|
|
select OF_BOARD_SETUP
|
|
|
|
endchoice
|
|
|
|
config ARCH_UNIPHIER_LD4
|
|
bool "Enable UniPhier PH1-LD4 SoC support"
|
|
depends on ARCH_UNIPHIER_LD4_SLD8
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_SLD8
|
|
bool "Enable UniPhier PH1-sLD8 SoC support"
|
|
depends on ARCH_UNIPHIER_LD4_SLD8
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_PRO5
|
|
bool "Enable UniPhier PH1-Pro5 SoC support"
|
|
depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_PXS2
|
|
bool "Enable UniPhier ProXstream2 SoC support"
|
|
depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
|
|
default y
|
|
|
|
config ARCH_UNIPHIER_LD6B
|
|
bool "Enable UniPhier PH1-LD6b SoC support"
|
|
depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
|
|
default y
|
|
|
|
config MICRO_SUPPORT_CARD
|
|
bool "Use Micro Support Card"
|
|
help
|
|
This option provides support for the expansion board, available
|
|
on some UniPhier reference boards.
|
|
|
|
Say Y to use the on-board UART, Ether, LED devices.
|
|
|
|
config CMD_PINMON
|
|
bool "Enable boot mode pins monitor command"
|
|
default y
|
|
help
|
|
The command "pinmon" shows the state of the boot mode pins.
|
|
The boot mode pins are latched when the system reset is deasserted
|
|
and determine which device the system should load a boot image from.
|
|
|
|
config CMD_DDRPHY_DUMP
|
|
bool "Enable dump command of DDR PHY parameters"
|
|
depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
|
|
default y
|
|
help
|
|
The command "ddrphy" shows the resulting parameters of DDR PHY
|
|
training; it is useful for the evaluation of DDR PHY training.
|
|
|
|
config CMD_DDRMPHY_DUMP
|
|
bool "Enable dump command of DDR Multi PHY parameters"
|
|
depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
|
|
default y
|
|
help
|
|
The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
|
|
training; it is useful for the evaluation of DDR Multi PHY training.
|
|
|
|
endif
|