mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-11 22:03:15 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
119 lines
3 KiB
C
119 lines
3 KiB
C
/*
|
|
* pci.c -- esd VME8349 PCI board support.
|
|
* Copyright (c) 2006 Wind River Systems, Inc.
|
|
* Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
|
|
* Copyright (c) 2009 esd gmbh.
|
|
*
|
|
* Reinhard Arlt <reinhard.arlt@esd-electronics.com>
|
|
*
|
|
* Based on MPC8349 PCI support but w/o PIB related code.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <asm/mmu.h>
|
|
#include <asm/io.h>
|
|
#include <common.h>
|
|
#include <mpc83xx.h>
|
|
#include <pci.h>
|
|
#include <i2c.h>
|
|
#include <asm/fsl_i2c.h>
|
|
#include "vme8349pin.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
static struct pci_region pci1_regions[] = {
|
|
{
|
|
bus_start: CONFIG_SYS_PCI1_MEM_BASE,
|
|
phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
|
|
size: CONFIG_SYS_PCI1_MEM_SIZE,
|
|
flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
|
|
},
|
|
{
|
|
bus_start: CONFIG_SYS_PCI1_IO_BASE,
|
|
phys_start: CONFIG_SYS_PCI1_IO_PHYS,
|
|
size: CONFIG_SYS_PCI1_IO_SIZE,
|
|
flags: PCI_REGION_IO
|
|
},
|
|
{
|
|
bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
|
|
phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
|
|
size: CONFIG_SYS_PCI1_MMIO_SIZE,
|
|
flags: PCI_REGION_MEM
|
|
},
|
|
};
|
|
|
|
/*
|
|
* pci_init_board()
|
|
*
|
|
* NOTICE: PCI2 is not supported. There is only one
|
|
* physical PCI slot on the board.
|
|
*
|
|
*/
|
|
void
|
|
pci_init_board(void)
|
|
{
|
|
volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
|
|
volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
|
|
volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
|
|
struct pci_region *reg[] = { pci1_regions };
|
|
u8 reg8;
|
|
int monarch = 0;
|
|
|
|
i2c_set_bus_num(1);
|
|
/* Read the PCI_M66EN jumper setting */
|
|
if ((i2c_read(CONFIG_SYS_I2C_8574_ADDR2, 0, 0, ®8, 1) == 0) ||
|
|
(i2c_read(0x38 , 0, 0, ®8, 1) == 0)) {
|
|
if (reg8 & 0x40) {
|
|
clk->occr = 0xff000000; /* 66 MHz PCI */
|
|
printf("PCI: 66MHz\n");
|
|
} else {
|
|
clk->occr = 0xffff0003; /* 33 MHz PCI */
|
|
printf("PCI: 33MHz\n");
|
|
}
|
|
if (((reg8 & 0x01) == 0) || ((reg8 & 0x02) == 0))
|
|
monarch = 1;
|
|
} else {
|
|
clk->occr = 0xffff0003; /* 33 MHz PCI */
|
|
printf("PCI: 33MHz (I2C read failed)\n");
|
|
}
|
|
udelay(2000);
|
|
|
|
/*
|
|
* Assert/deassert VME reset
|
|
*/
|
|
clrsetbits_be32(&immr->gpio[1].dat,
|
|
GPIO2_TSI_POWERUP_RESET_N | GPIO2_TSI_PLL_RESET_N,
|
|
GPIO2_VME_RESET_N | GPIO2_L_RESET_EN_N);
|
|
setbits_be32(&immr->gpio[1].dir, GPIO2_TSI_PLL_RESET_N |
|
|
GPIO2_TSI_POWERUP_RESET_N |
|
|
GPIO2_VME_RESET_N |
|
|
GPIO2_L_RESET_EN_N);
|
|
clrbits_be32(&immr->gpio[1].dir, GPIO2_V_SCON);
|
|
udelay(200);
|
|
setbits_be32(&immr->gpio[1].dat, GPIO2_TSI_PLL_RESET_N);
|
|
udelay(200);
|
|
setbits_be32(&immr->gpio[1].dat, GPIO2_TSI_POWERUP_RESET_N);
|
|
udelay(600000);
|
|
clrbits_be32(&immr->gpio[1].dat, GPIO2_L_RESET_EN_N);
|
|
|
|
/* Configure PCI Local Access Windows */
|
|
pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
|
|
pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
|
|
|
|
pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
|
|
pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M;
|
|
|
|
udelay(2000);
|
|
|
|
if (monarch == 0) {
|
|
mpc83xx_pci_init(1, reg);
|
|
} else {
|
|
/*
|
|
* Release PCI RST Output signal
|
|
*/
|
|
out_be32(&immr->pci_ctrl[0].gcr, 0);
|
|
udelay(2000);
|
|
out_be32(&immr->pci_ctrl[0].gcr, 1);
|
|
}
|
|
}
|