u-boot/include/configs/imx8mm_data_modul_edm_sbc.h
Peng Fan 6ea118ef9a imx: imx8mm_edm_sbc: Enable SPL_DM_SERIAL
Enable CONFIG_SPL_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-05-20 09:30:28 +02:00

126 lines
4.2 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2022 Marek Vasut <marex@denx.de>
*/
#ifndef __IMX8MM_DATA_MODUL_EDM_SBC_H
#define __IMX8MM_DATA_MODUL_EDM_SBC_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>
#define CONFIG_SYS_BOOTM_LEN SZ_128M
#define CONFIG_SPL_MAX_SIZE (148 * 1024)
#define CONFIG_SYS_MONITOR_LEN SZ_1M
#define CONFIG_SPL_STACK 0x920000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_BSS_START_ADDR 0x910000
#define CONFIG_SPL_BSS_MAX_SIZE SZ_8K /* 8 kiB */
#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M /* 16 MiB */
#define CONFIG_MALLOC_F_ADDR 0x930000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#endif
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x200000
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE 0x40000000 /* Minimum 1 GiB DDR */
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 2048
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* PHY needs a longer autonegotiation timeout after reset */
#define PHY_ANEG_TIMEOUT 20000
/* USDHC */
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#if !defined(CONFIG_SPL_BUILD)
#define CONFIG_EXTRA_ENV_SETTINGS \
"altbootcmd=setenv devpart 2 && run bootcmd ; reset\0" \
"bootlimit=3\0" \
"devtype=mmc\0" \
"devpart=1\0" \
/* Give slow devices beyond USB HUB chance to come up. */ \
"usb_pgood_delay=2000\0" \
"dfu_alt_info=" \
/* RAM block at DRAM offset 256..768 MiB */ \
"ram ram0=ram ram 0x50000000 0x20000000&" \
/* 16 MiB SPI NOR */ \
"mtd nor0=sf raw 0x0 0x1000000\0" \
"dmo_preboot=" \
"sf probe ; " /* Scan for SPI NOR, needed by DFU */ \
"run dmo_usb_start_hub ; " \
/* Attempt to start USB and Network console */ \
"run dmo_usb_cdc_acm_start ; " \
"run dmo_netconsole_start\0" \
"dmo_update_env=" \
"setenv dmo_update_env true ; saveenv ; saveenv\0" \
"dmo_usb_cdc_acm_start=" \
"if test \"${dmo_usb_cdc_acm_enabled}\" = \"true\" ; then "\
/* Ungate IMX8MM_CLK_USB1_CTRL_ROOT */ \
"mw 0x303844d0 3 ; " \
/* Read USBNC_n_PHY_STATUS BIT(4) VBUS_VLD */ \
"setexpr.l usbnc_n_phy_status *0x32e4023c \\\\& 0x8 ; " \
/* If USB OTG has valid VBUS, enable CDC ACM */ \
"if test \"${usbnc_n_phy_status}\" -eq 8 ; then "\
"usb start && " \
"setenv stderr ${stderr},usbacm && " \
"setenv stdout ${stdout},usbacm && " \
"setenv stdin ${stdin},usbacm ; " \
"fi ; " \
"fi\0" \
"dmo_usb_start_hub=" \
"i2c dev 1 ; " \
/* Reset the USB USB */ \
"gpio clear GPIO5_2 ; sleep 0.01 ; " /* t1 > 1us */ \
"gpio set GPIO5_2 ; sleep 0.01 ; " /* t5 > 3us */ \
/* Write chunks of descriptor into the USB HUB */ \
"mw.l 0x7e1000 0x14042417 ; mw.l 0x7e1004 0x9b0bb325 ; "\
"mw.l 0x7e1008 0x00000220 ; mw.l 0x7e100c 0x01320100 ; "\
"mw.l 0x7e1010 0x00003232 ; mw.l 0x7e1014 0x4d000909 ; "\
"i2c write 0x7e1000 0x2c 0x00 0x18 -s ; " \
"mw.l 0x7e1000 0x6300690f ; mw.l 0x7e1004 0x6f007200 ; "\
"mw.l 0x7e1008 0x68006300 ; mw.l 0x7e100c 0x70006900 ; "\
"i2c write 0x7e1000 0x2c 0x18 0x10 -s ; " \
"mw.l 0x7e1000 0x53005511 ; mw.l 0x7e1004 0x32004200 ; "\
"mw.l 0x7e1008 0x31003500 ; mw.l 0x7e100c 0x42003400 ; "\
"mw.l 0x7e1010 0x00006900 ; " \
"i2c write 0x7e1000 0x2c 0x54 0x12 -s ; " \
"mw.l 0x7e1000 0x00000101 ; " \
"i2c write 0x7e1000 0x2c 0xff 0x2 -s\0" \
"dmo_netconsole_start=" \
"if test \"${dmo_netconsole_enabled}\" = \"true\" ; then "\
"setenv autoload false && " \
"dhcp && " \
"setenv autoload && " \
"setenv ncip ${serverip} && " \
"setenv stderr ${stderr},nc && " \
"setenv stdout ${stdout},nc && " \
"setenv stdin ${stdin},nc ; " \
"fi"
#endif
#endif