mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-16 17:58:23 +00:00
f40574e2d7
Move this in to Kconfig with a default of 115200. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
312 lines
10 KiB
C
312 lines
10 KiB
C
/*
|
|
* (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* config for XPedite1000 from XES Inc.
|
|
* Ported from EBONY config by Travis B. Sawyer <tsawyer@sandburst.com>
|
|
* (C) Copyright 2003 Sandburst Corporation
|
|
* board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/* High Level Configuration Options */
|
|
#define CONFIG_XPEDITE1000 1
|
|
#define CONFIG_SYS_BOARD_NAME "XPedite1000"
|
|
#define CONFIG_SYS_FORM_PMC 1
|
|
#define CONFIG_440 1
|
|
#define CONFIG_440GX 1 /* 440 GX */
|
|
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFF80000
|
|
|
|
/*
|
|
* DDR config
|
|
*/
|
|
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
|
|
#define SPD_EEPROM_ADDRESS {0x54} /* SPD i2c spd addresses */
|
|
#define CONFIG_VERY_BIG_RAM 1
|
|
|
|
/*
|
|
* Base addresses -- Note these are effective addresses where the
|
|
* actual resources get mapped (not physical addresses)
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
|
|
#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
|
|
#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
|
|
#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
|
|
#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
|
|
|
|
/*
|
|
* Diagnostics
|
|
*/
|
|
#define CONFIG_SYS_ALT_MEMTEST
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000
|
|
|
|
/* POST support */
|
|
#define CONFIG_POST (CONFIG_SYS_POST_RTC | \
|
|
CONFIG_SYS_POST_I2C)
|
|
|
|
/*
|
|
* LED support
|
|
*/
|
|
#define USR_LED0 0x00000080
|
|
#define USR_LED1 0x00000100
|
|
#define USR_LED2 0x00000200
|
|
#define USR_LED3 0x00000400
|
|
|
|
#ifndef __ASSEMBLY__
|
|
extern unsigned long in32(unsigned int);
|
|
extern void out32(unsigned int, unsigned long);
|
|
|
|
#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0))
|
|
#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1))
|
|
#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2))
|
|
#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3))
|
|
|
|
#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0))
|
|
#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1))
|
|
#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2))
|
|
#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3))
|
|
#endif
|
|
|
|
/*
|
|
* Use internal SRAM for initial stack
|
|
*/
|
|
#define CONFIG_SYS_TEMP_STACK_OCM 1
|
|
#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
|
|
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* NOR flash configuration
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 3
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, 0xf0000000, 0xf4000000 }
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
|
|
#define CONFIG_FLASH_CFI_DRIVER
|
|
#define CONFIG_SYS_FLASH_CFI
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
|
|
#define CONFIG_SYS_FLASH_QUIET_TEST /* MirrorBit flashes are optional */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
/*
|
|
* I2C
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_PPC4XX
|
|
#define CONFIG_SYS_I2C_PPC4XX_CH0
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
|
|
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7f
|
|
|
|
/* I2C EEPROM */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
|
|
|
|
/* I2C RTC: STMicro M41T00 */
|
|
#define CONFIG_RTC_M41T11 1
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#define CONFIG_SYS_M41T11_BASE_YEAR 2000
|
|
|
|
/*
|
|
* PCI
|
|
*/
|
|
/* General PCI */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
|
|
|
|
/* Board-specific PCI */
|
|
#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
|
|
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
|
|
#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */
|
|
|
|
/*
|
|
* Networking options
|
|
*/
|
|
#define CONFIG_PPC4xx_EMAC
|
|
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
|
|
#define CONFIG_ETHPRIME "ppc_4xx_eth2"
|
|
#define CONFIG_PHY_ADDR 4 /* PHY address phy0 not populated */
|
|
#define CONFIG_PHY2_ADDR 4 /* PHY address phy2 */
|
|
#define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */
|
|
#define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */
|
|
#define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */
|
|
|
|
/* BOOTP options */
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
/*
|
|
* Command configuration
|
|
*/
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_JFFS2
|
|
#define CONFIG_CMD_PCI
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
#define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */
|
|
#define CONFIG_PANIC_HANG /* do not reset board on panic */
|
|
#define CONFIG_PREBOOT /* enable preboot variable */
|
|
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
|
|
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
|
|
#define CONFIG_ENV_SIZE 0x8000
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
|
|
|
|
/*
|
|
* Flash memory map:
|
|
* fff80000 - ffffffff U-Boot (512 KB)
|
|
* fff40000 - fff7ffff U-Boot Environment (256 KB)
|
|
* fff00000 - fff3ffff FDT (256KB)
|
|
* ffc00000 - ffefffff OS image (3MB)
|
|
* ff000000 - ffbfffff OS Use/Filesystem (12MB)
|
|
*/
|
|
|
|
#define CONFIG_UBOOT_ENV_ADDR __stringify(CONFIG_SYS_TEXT_BASE)
|
|
#define CONFIG_FDT_ENV_ADDR __stringify(0xfff00000)
|
|
#define CONFIG_OS_ENV_ADDR __stringify(0xffc00000)
|
|
|
|
#define CONFIG_PROG_UBOOT \
|
|
"$download_cmd $loadaddr $ubootfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"protect off "CONFIG_UBOOT_ENV_ADDR" +80000; " \
|
|
"erase "CONFIG_UBOOT_ENV_ADDR" +80000; " \
|
|
"cp.w $loadaddr "CONFIG_UBOOT_ENV_ADDR" 40000; " \
|
|
"protect on "CONFIG_UBOOT_ENV_ADDR" +80000; " \
|
|
"cmp.b $loadaddr "CONFIG_UBOOT_ENV_ADDR" 80000; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_BOOT_OS_NET \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"if test -n $fdtaddr; then " \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"bootm $osaddr - $fdtaddr; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"bootm $osaddr; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_OS \
|
|
"$download_cmd $osaddr $osfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_OS_ENV_ADDR" +$filesize; " \
|
|
"cp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \
|
|
"cmp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo OS PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo OS PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo OS DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_PROG_FDT \
|
|
"$download_cmd $fdtaddr $fdtfile; " \
|
|
"if test $? -eq 0; then " \
|
|
"erase "CONFIG_FDT_ENV_ADDR" +$filesize;" \
|
|
"cp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \
|
|
"cmp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \
|
|
"if test $? -ne 0; then " \
|
|
"echo FDT PROGRAM FAILED; " \
|
|
"else; " \
|
|
"echo FDT PROGRAM SUCCEEDED; " \
|
|
"fi; " \
|
|
"else; " \
|
|
"echo FDT DOWNLOAD FAILED; " \
|
|
"fi;"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"autoload=yes\0" \
|
|
"download_cmd=tftp\0" \
|
|
"console_args=console=ttyS0,115200\0" \
|
|
"root_args=root=/dev/nfs rw\0" \
|
|
"misc_args=ip=on\0" \
|
|
"set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
|
|
"bootfile=/home/user/file\0" \
|
|
"osfile=/home/user/board.uImage\0" \
|
|
"fdtfile=/home/user/board.dtb\0" \
|
|
"ubootfile=/home/user/u-boot.bin\0" \
|
|
"fdtaddr=0x1e00000\0" \
|
|
"osaddr=0x1000000\0" \
|
|
"loadaddr=0x1000000\0" \
|
|
"prog_uboot="CONFIG_PROG_UBOOT"\0" \
|
|
"prog_os="CONFIG_PROG_OS"\0" \
|
|
"prog_fdt="CONFIG_PROG_FDT"\0" \
|
|
"bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
|
|
"bootcmd_flash=run set_bootargs; " \
|
|
"bootm "CONFIG_OS_ENV_ADDR" - "CONFIG_FDT_ENV_ADDR"\0" \
|
|
"bootcmd=run bootcmd_flash\0"
|
|
#endif /* __CONFIG_H */
|