u-boot/drivers/rtc/zynqmp_rtc.c
Michal Simek 1f065e8fea rtc: zynqmp: Add support for ZynqMP RTC
The whole driver logic is taken from Linux kernel but only set/get/reset
functions are implemented. When device is power off RTC is power out of
battery.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-06 09:32:02 +02:00

158 lines
3.8 KiB
C

// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2021, Xilinx, Inc.
*/
#define LOG_CATEGORY UCLASS_RTC
#include <common.h>
#include <dm.h>
#include <rtc.h>
#include <asm/io.h>
/* RTC Registers */
#define RTC_SET_TM_WR 0x00
#define RTC_SET_TM_RD 0x04
#define RTC_CALIB_WR 0x08
#define RTC_CUR_TM 0x10
#define RTC_INT_STS 0x20
#define RTC_CTRL 0x40
#define RTC_INT_SEC BIT(0)
#define RTC_BATT_EN BIT(31)
#define RTC_CALIB_DEF 0x198233
#define RTC_CALIB_MASK 0x1FFFFF
struct zynqmp_rtc_priv {
fdt_addr_t base;
unsigned int calibval;
};
static int zynqmp_rtc_get(struct udevice *dev, struct rtc_time *tm)
{
struct zynqmp_rtc_priv *priv = dev_get_priv(dev);
u32 status;
unsigned long read_time;
status = readl(priv->base + RTC_INT_STS);
if (status & RTC_INT_SEC) {
/*
* RTC has updated the CURRENT_TIME with the time written into
* SET_TIME_WRITE register.
*/
read_time = readl(priv->base + RTC_CUR_TM);
} else {
/*
* Time written in SET_TIME_WRITE has not yet updated into
* the seconds read register, so read the time from the
* SET_TIME_WRITE instead of CURRENT_TIME register.
* Since we add +1 sec while writing, we need to -1 sec while
* reading.
*/
read_time = readl(priv->base + RTC_SET_TM_RD) - 1;
}
rtc_to_tm(read_time, tm);
return 0;
}
static int zynqmp_rtc_set(struct udevice *dev, const struct rtc_time *tm)
{
struct zynqmp_rtc_priv *priv = dev_get_priv(dev);
unsigned long new_time = 0;
if (tm)
/*
* The value written will be updated after 1 sec into the
* seconds read register, so we need to program time +1 sec
* to get the correct time on read.
*/
new_time = rtc_mktime(tm) + 1;
/*
* Writing into calibration register will clear the Tick Counter and
* force the next second to be signaled exactly in 1 second period
*/
priv->calibval &= RTC_CALIB_MASK;
writel(priv->calibval, (priv->base + RTC_CALIB_WR));
writel(new_time, priv->base + RTC_SET_TM_WR);
/*
* Clear the rtc interrupt status register after setting the
* time. During a read_time function, the code should read the
* RTC_INT_STATUS register and if bit 0 is still 0, it means
* that one second has not elapsed yet since RTC was set and
* the current time should be read from SET_TIME_READ register;
* otherwise, CURRENT_TIME register is read to report the time
*/
writel(RTC_INT_SEC, priv->base + RTC_INT_STS);
return 0;
}
static int zynqmp_rtc_reset(struct udevice *dev)
{
return zynqmp_rtc_set(dev, NULL);
}
static int zynqmp_rtc_init(struct udevice *dev)
{
struct zynqmp_rtc_priv *priv = dev_get_priv(dev);
u32 rtc_ctrl;
/* Enable RTC switch to battery when VCC_PSAUX is not available */
rtc_ctrl = readl(priv->base + RTC_CTRL);
rtc_ctrl |= RTC_BATT_EN;
writel(rtc_ctrl, priv->base + RTC_CTRL);
/*
* Based on crystal freq of 33.330 KHz
* set the seconds counter and enable, set fractions counter
* to default value suggested as per design spec
* to correct RTC delay in frequency over period of time.
*/
priv->calibval &= RTC_CALIB_MASK;
writel(priv->calibval, (priv->base + RTC_CALIB_WR));
return 0;
}
static int zynqmp_rtc_probe(struct udevice *dev)
{
struct zynqmp_rtc_priv *priv = dev_get_priv(dev);
int ret;
priv->base = dev_read_addr(dev);
if (priv->base == FDT_ADDR_T_NONE)
return -EINVAL;
priv->calibval = dev_read_u32_default(dev, "calibration",
RTC_CALIB_DEF);
ret = zynqmp_rtc_init(dev);
return ret;
}
static const struct rtc_ops zynqmp_rtc_ops = {
.get = zynqmp_rtc_get,
.set = zynqmp_rtc_set,
.reset = zynqmp_rtc_reset,
};
static const struct udevice_id zynqmp_rtc_ids[] = {
{ .compatible = "xlnx,zynqmp-rtc" },
{ }
};
U_BOOT_DRIVER(rtc_zynqmp) = {
.name = "rtc-zynqmp",
.id = UCLASS_RTC,
.probe = zynqmp_rtc_probe,
.of_match = zynqmp_rtc_ids,
.ops = &zynqmp_rtc_ops,
.priv_auto = sizeof(struct zynqmp_rtc_priv),
};