mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-29 16:10:58 +00:00
bfebc8c965
We are now using an env_ prefix for environment functions. Rename these for consistency. Also add function comments in common.h. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
430 lines
10 KiB
C
430 lines
10 KiB
C
/*
|
|
* board.c
|
|
*
|
|
* Board functions for Birdland Audio BAV335x Network Processor
|
|
*
|
|
* Copyright (c) 2012-2014 Birdland Audio - http://birdland.com/oem
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <errno.h>
|
|
#include <spl.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/arch/omap.h>
|
|
#include <asm/arch/ddr_defs.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/mmc_host_def.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/mem.h>
|
|
#include <asm/io.h>
|
|
#include <asm/emif.h>
|
|
#include <asm/gpio.h>
|
|
#include <i2c.h>
|
|
#include <miiphy.h>
|
|
#include <cpsw.h>
|
|
#include <power/tps65217.h>
|
|
#include <power/tps65910.h>
|
|
#include <environment.h>
|
|
#include <watchdog.h>
|
|
#include <environment.h>
|
|
#include "board.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* GPIO that controls power to DDR on EVM-SK */
|
|
#define GPIO_DDR_VTT_EN 7
|
|
|
|
static __maybe_unused struct ctrl_dev *cdev =
|
|
(struct ctrl_dev *)CTRL_DEVICE_BASE;
|
|
|
|
|
|
|
|
/*
|
|
* Read header information from EEPROM into global structure.
|
|
*/
|
|
static int read_eeprom(struct board_eeconfig *header)
|
|
{
|
|
/* Check if baseboard eeprom is available */
|
|
if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR))
|
|
return -ENODEV;
|
|
|
|
/* read the eeprom using i2c */
|
|
if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
|
|
sizeof(struct board_eeconfig)))
|
|
return -EIO;
|
|
|
|
if (header->magic != BOARD_MAGIC) {
|
|
/* read the i2c eeprom again using only a 1 byte address */
|
|
if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
|
|
sizeof(struct board_eeconfig)))
|
|
return -EIO;
|
|
|
|
if (header->magic != BOARD_MAGIC)
|
|
return -EINVAL;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
|
|
|
|
|
|
enum board_type get_board_type(bool debug)
|
|
{
|
|
int ecode;
|
|
struct board_eeconfig header;
|
|
|
|
ecode = read_eeprom(&header);
|
|
if (ecode == 0) {
|
|
if (header.version[1] == 'A') {
|
|
if (debug)
|
|
puts("=== Detected Board model BAV335x Rev.A");
|
|
return BAV335A;
|
|
} else if (header.version[1] == 'B') {
|
|
if (debug)
|
|
puts("=== Detected Board model BAV335x Rev.B");
|
|
return BAV335B;
|
|
} else if (debug) {
|
|
puts("### Un-known board model in serial-EE\n");
|
|
}
|
|
} else if (debug) {
|
|
switch (ecode) {
|
|
case -ENODEV:
|
|
puts("### Board doesn't have a serial-EE\n");
|
|
break;
|
|
case -EINVAL:
|
|
puts("### Board serial-EE signature is incorrect.\n");
|
|
break;
|
|
default:
|
|
puts("### IO Error reading serial-EE.\n");
|
|
break;
|
|
}
|
|
}
|
|
|
|
#if (CONFIG_BAV_VERSION == 1)
|
|
if (debug)
|
|
puts("### Selecting BAV335A as per config\n");
|
|
return BAV335A;
|
|
#elif (CONFIG_BAV_VERSION == 2)
|
|
if (debug)
|
|
puts("### Selecting BAV335B as per config\n");
|
|
return BAV335B;
|
|
#endif
|
|
#if (NOT_DEFINED == 2)
|
|
#error "SHOULD NEVER DISPLAY THIS"
|
|
#endif
|
|
|
|
if (debug)
|
|
puts("### Defaulting to model BAV335x Rev.B\n");
|
|
return BAV335B;
|
|
}
|
|
|
|
|
|
|
|
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
|
|
static const struct ddr_data ddr3_bav335x_data = {
|
|
.datardsratio0 = MT41K256M16HA125E_RD_DQS,
|
|
.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
|
|
.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
|
|
.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
|
|
};
|
|
|
|
static const struct cmd_control ddr3_bav335x_cmd_ctrl_data = {
|
|
.cmd0csratio = MT41K256M16HA125E_RATIO,
|
|
.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
|
|
.cmd1csratio = MT41K256M16HA125E_RATIO,
|
|
.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
|
|
.cmd2csratio = MT41K256M16HA125E_RATIO,
|
|
.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
|
|
};
|
|
|
|
|
|
static struct emif_regs ddr3_bav335x_emif_reg_data = {
|
|
.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
|
|
.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
|
|
.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
|
|
.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
|
|
.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
|
|
.zq_config = MT41K256M16HA125E_ZQ_CFG,
|
|
.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
|
|
};
|
|
|
|
|
|
#ifdef CONFIG_SPL_OS_BOOT
|
|
int spl_start_uboot(void)
|
|
{
|
|
/* break into full u-boot on 'c' */
|
|
if (serial_tstc() && serial_getc() == 'c')
|
|
return 1;
|
|
|
|
#ifdef CONFIG_SPL_ENV_SUPPORT
|
|
env_init();
|
|
env_load();
|
|
if (env_get_yesno("boot_os") != 1)
|
|
return 1;
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#define OSC (V_OSCK/1000000)
|
|
const struct dpll_params dpll_ddr = {
|
|
266, OSC-1, 1, -1, -1, -1, -1};
|
|
const struct dpll_params dpll_ddr_evm_sk = {
|
|
303, OSC-1, 1, -1, -1, -1, -1};
|
|
const struct dpll_params dpll_ddr_bone_black = {
|
|
400, OSC-1, 1, -1, -1, -1, -1};
|
|
|
|
void am33xx_spl_board_init(void)
|
|
{
|
|
/* debug print detect status */
|
|
(void)get_board_type(true);
|
|
|
|
/* Get the frequency */
|
|
/* dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev); */
|
|
dpll_mpu_opp100.m = MPUPLL_M_1000;
|
|
|
|
if (i2c_probe(TPS65217_CHIP_PM))
|
|
return;
|
|
|
|
/* Set the USB Current Limit */
|
|
if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
|
|
TPS65217_USB_INPUT_CUR_LIMIT_1800MA,
|
|
TPS65217_USB_INPUT_CUR_LIMIT_MASK))
|
|
puts("! tps65217_reg_write: could not set USB limit\n");
|
|
|
|
/* Set the Core Voltage (DCDC3) to 1.125V */
|
|
if (tps65217_voltage_update(TPS65217_DEFDCDC3,
|
|
TPS65217_DCDC_VOLT_SEL_1125MV)) {
|
|
puts("! tps65217_reg_write: could not set Core Voltage\n");
|
|
return;
|
|
}
|
|
|
|
/* Set CORE Frequencies to OPP100 */
|
|
do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
|
|
|
|
/* Set the MPU Voltage (DCDC2) */
|
|
if (tps65217_voltage_update(TPS65217_DEFDCDC2,
|
|
TPS65217_DCDC_VOLT_SEL_1325MV)) {
|
|
puts("! tps65217_reg_write: could not set MPU Voltage\n");
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
|
|
* Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
|
|
*/
|
|
if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS1,
|
|
TPS65217_LDO_VOLTAGE_OUT_1_8, TPS65217_LDO_MASK))
|
|
puts("! tps65217_reg_write: could not set LDO3\n");
|
|
|
|
if (tps65217_reg_write(TPS65217_PROT_LEVEL_2, TPS65217_DEFLS2,
|
|
TPS65217_LDO_VOLTAGE_OUT_3_3, TPS65217_LDO_MASK))
|
|
puts("! tps65217_reg_write: could not set LDO4\n");
|
|
|
|
/* Set MPU Frequency to what we detected now that voltages are set */
|
|
do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
|
|
}
|
|
|
|
const struct dpll_params *get_dpll_ddr_params(void)
|
|
{
|
|
enable_i2c0_pin_mux();
|
|
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
|
|
|
|
return &dpll_ddr_bone_black;
|
|
}
|
|
|
|
void set_uart_mux_conf(void)
|
|
{
|
|
#if CONFIG_CONS_INDEX == 1
|
|
enable_uart0_pin_mux();
|
|
#elif CONFIG_CONS_INDEX == 2
|
|
enable_uart1_pin_mux();
|
|
#elif CONFIG_CONS_INDEX == 3
|
|
enable_uart2_pin_mux();
|
|
#elif CONFIG_CONS_INDEX == 4
|
|
enable_uart3_pin_mux();
|
|
#elif CONFIG_CONS_INDEX == 5
|
|
enable_uart4_pin_mux();
|
|
#elif CONFIG_CONS_INDEX == 6
|
|
enable_uart5_pin_mux();
|
|
#endif
|
|
}
|
|
|
|
void set_mux_conf_regs(void)
|
|
{
|
|
enum board_type board;
|
|
|
|
board = get_board_type(false);
|
|
enable_board_pin_mux(board);
|
|
}
|
|
|
|
const struct ctrl_ioregs ioregs_bonelt = {
|
|
.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
};
|
|
|
|
|
|
void sdram_init(void)
|
|
{
|
|
config_ddr(400, &ioregs_bonelt,
|
|
&ddr3_bav335x_data,
|
|
&ddr3_bav335x_cmd_ctrl_data,
|
|
&ddr3_bav335x_emif_reg_data, 0);
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* Basic board specific setup. Pinmux has been handled already.
|
|
*/
|
|
int board_init(void)
|
|
{
|
|
#if defined(CONFIG_HW_WATCHDOG)
|
|
hw_watchdog_init();
|
|
#endif
|
|
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
#if defined(CONFIG_NOR) || defined(CONFIG_NAND)
|
|
gpmc_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_BOARD_LATE_INIT
|
|
int board_late_init(void)
|
|
{
|
|
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
|
env_set("board_name", "BAV335xB");
|
|
env_set("board_rev", "B"); /* Fix me, but why bother.. */
|
|
#endif
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
|
|
#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
|
|
(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
|
|
static void cpsw_control(int enabled)
|
|
{
|
|
/* VTP can be added here */
|
|
return;
|
|
}
|
|
|
|
static struct cpsw_slave_data cpsw_slaves[] = {
|
|
{
|
|
.slave_reg_ofs = 0x208,
|
|
.sliver_reg_ofs = 0xd80,
|
|
.phy_addr = 0,
|
|
},
|
|
{
|
|
.slave_reg_ofs = 0x308,
|
|
.sliver_reg_ofs = 0xdc0,
|
|
.phy_addr = 1,
|
|
},
|
|
};
|
|
|
|
static struct cpsw_platform_data cpsw_data = {
|
|
.mdio_base = CPSW_MDIO_BASE,
|
|
.cpsw_base = CPSW_BASE,
|
|
.mdio_div = 0xff,
|
|
.channels = 8,
|
|
.cpdma_reg_ofs = 0x800,
|
|
.slaves = 1,
|
|
.slave_data = cpsw_slaves,
|
|
.ale_reg_ofs = 0xd00,
|
|
.ale_entries = 1024,
|
|
.host_port_reg_ofs = 0x108,
|
|
.hw_stats_reg_ofs = 0x900,
|
|
.bd_ram_ofs = 0x2000,
|
|
.mac_control = (1 << 5),
|
|
.control = cpsw_control,
|
|
.host_port_num = 0,
|
|
.version = CPSW_CTRL_VERSION_2,
|
|
};
|
|
#endif
|
|
|
|
|
|
/*
|
|
* This function will:
|
|
* Perform fixups to the PHY present on certain boards. We only need this
|
|
* function in:
|
|
* - SPL with either CPSW or USB ethernet support
|
|
* - Full U-Boot, with either CPSW or USB ethernet
|
|
* Build in only these cases to avoid warnings about unused variables
|
|
* when we build an SPL that has neither option but full U-Boot will.
|
|
*/
|
|
#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) &&\
|
|
defined(CONFIG_SPL_BUILD)) || \
|
|
((defined(CONFIG_DRIVER_TI_CPSW) || \
|
|
defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \
|
|
!defined(CONFIG_SPL_BUILD))
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int ecode, rv, n;
|
|
uint8_t mac_addr[6];
|
|
struct board_eeconfig header;
|
|
__maybe_unused enum board_type board;
|
|
|
|
/* Default manufacturing address; used when no EE or invalid */
|
|
n = 0;
|
|
mac_addr[0] = 0;
|
|
mac_addr[1] = 0x20;
|
|
mac_addr[2] = 0x18;
|
|
mac_addr[3] = 0x1C;
|
|
mac_addr[4] = 0x00;
|
|
mac_addr[5] = 0x01;
|
|
|
|
ecode = read_eeprom(&header);
|
|
/* if we have a valid EE, get mac address from there */
|
|
if ((ecode == 0) &&
|
|
is_valid_ethaddr((const u8 *)&header.mac_addr[0][0])) {
|
|
memcpy(mac_addr, (const void *)&header.mac_addr[0][0], 6);
|
|
}
|
|
|
|
|
|
#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
|
|
(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
|
|
|
|
if (!env_get("ethaddr")) {
|
|
printf("<ethaddr> not set. Validating first E-fuse MAC\n");
|
|
|
|
if (is_valid_ethaddr(mac_addr))
|
|
eth_env_set_enetaddr("ethaddr", mac_addr);
|
|
}
|
|
|
|
#ifdef CONFIG_DRIVER_TI_CPSW
|
|
|
|
board = get_board_type(false);
|
|
|
|
/* Rev.A uses 10/100 PHY in mii mode */
|
|
if (board == BAV335A) {
|
|
writel(MII_MODE_ENABLE, &cdev->miisel);
|
|
cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
|
|
cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII;
|
|
}
|
|
/* Rev.B (default) uses GB PHY in rmii mode */
|
|
else {
|
|
writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel);
|
|
cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if
|
|
= PHY_INTERFACE_MODE_RGMII;
|
|
}
|
|
|
|
rv = cpsw_register(&cpsw_data);
|
|
if (rv < 0)
|
|
printf("Error %d registering CPSW switch\n", rv);
|
|
else
|
|
n += rv;
|
|
#endif
|
|
|
|
#endif
|
|
|
|
return n;
|
|
}
|
|
#endif
|