mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-23 11:33:32 +00:00
e0feee58ac
Also use the TPS65910 driver directly. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
486 lines
11 KiB
C
486 lines
11 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* board.c
|
|
*
|
|
* Board functions for TI AM335X based boards
|
|
*
|
|
* Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <env.h>
|
|
#include <errno.h>
|
|
#include <init.h>
|
|
#include <net.h>
|
|
#include <serial.h>
|
|
#include <asm/global_data.h>
|
|
#include <linux/libfdt.h>
|
|
#include <spl.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/arch/omap.h>
|
|
#include <asm/arch/ddr_defs.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/mmc_host_def.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/mem.h>
|
|
#include <asm/arch/mux.h>
|
|
#include <asm/io.h>
|
|
#include <asm/emif.h>
|
|
#include <asm/gpio.h>
|
|
#include <i2c.h>
|
|
#include <miiphy.h>
|
|
#include <cpsw.h>
|
|
#include <power/tps65910.h>
|
|
#include <watchdog.h>
|
|
#include "board.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* GPIO that controls DIP switch and mPCIe slot */
|
|
#define DIP_S1 44
|
|
#define MPCIE_SW 100
|
|
|
|
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
|
|
|
|
static int baltos_set_console(void)
|
|
{
|
|
int val, i, dips = 0;
|
|
char buf[7];
|
|
|
|
for (i = 0; i < 4; i++) {
|
|
sprintf(buf, "dip_s%d", i + 1);
|
|
|
|
if (gpio_request(DIP_S1 + i, buf)) {
|
|
printf("failed to export GPIO %d\n", DIP_S1 + i);
|
|
return 0;
|
|
}
|
|
|
|
if (gpio_direction_input(DIP_S1 + i)) {
|
|
printf("failed to set GPIO %d direction\n", DIP_S1 + i);
|
|
return 0;
|
|
}
|
|
|
|
val = gpio_get_value(DIP_S1 + i);
|
|
dips |= val << i;
|
|
}
|
|
|
|
printf("DIPs: 0x%1x\n", (~dips) & 0xf);
|
|
|
|
if ((dips & 0xf) == 0xe)
|
|
env_set("console", "ttyUSB0,115200n8");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int read_eeprom(BSP_VS_HWPARAM *header)
|
|
{
|
|
int rc;
|
|
struct udevice *dev;
|
|
struct udevice *bus;
|
|
|
|
rc = uclass_get_device_by_seq(UCLASS_I2C, 1, &bus);
|
|
if (rc)
|
|
return rc;
|
|
|
|
/* Check if baseboard eeprom is available */
|
|
if (dm_i2c_probe(bus, CONFIG_SYS_I2C_EEPROM_ADDR, 0, &dev)) {
|
|
puts("Could not probe the EEPROM; something fundamentally "
|
|
"wrong on the I2C bus.\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* read the eeprom using i2c */
|
|
if (dm_i2c_read(dev, 0, (uchar *)header,
|
|
sizeof(BSP_VS_HWPARAM))) {
|
|
puts("Could not read the EEPROM; something fundamentally"
|
|
" wrong on the I2C bus.\n");
|
|
return -EIO;
|
|
}
|
|
|
|
if (header->Magic != 0xDEADBEEF) {
|
|
|
|
printf("Incorrect magic number (0x%x) in EEPROM\n",
|
|
header->Magic);
|
|
|
|
/* fill default values */
|
|
header->SystemId = 211;
|
|
header->MAC1[0] = 0x00;
|
|
header->MAC1[1] = 0x00;
|
|
header->MAC1[2] = 0x00;
|
|
header->MAC1[3] = 0x00;
|
|
header->MAC1[4] = 0x00;
|
|
header->MAC1[5] = 0x01;
|
|
|
|
header->MAC2[0] = 0x00;
|
|
header->MAC2[1] = 0x00;
|
|
header->MAC2[2] = 0x00;
|
|
header->MAC2[3] = 0x00;
|
|
header->MAC2[4] = 0x00;
|
|
header->MAC2[5] = 0x02;
|
|
|
|
header->MAC3[0] = 0x00;
|
|
header->MAC3[1] = 0x00;
|
|
header->MAC3[2] = 0x00;
|
|
header->MAC3[3] = 0x00;
|
|
header->MAC3[4] = 0x00;
|
|
header->MAC3[5] = 0x03;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#if defined(CONFIG_SPL_BUILD) || defined(CONFIG_NOR_BOOT)
|
|
|
|
static const struct ddr_data ddr3_baltos_data = {
|
|
.datardsratio0 = MT41K256M16HA125E_RD_DQS,
|
|
.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
|
|
.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
|
|
.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
|
|
};
|
|
|
|
static const struct cmd_control ddr3_baltos_cmd_ctrl_data = {
|
|
.cmd0csratio = MT41K256M16HA125E_RATIO,
|
|
.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
|
|
|
|
.cmd1csratio = MT41K256M16HA125E_RATIO,
|
|
.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
|
|
|
|
.cmd2csratio = MT41K256M16HA125E_RATIO,
|
|
.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
|
|
};
|
|
|
|
static struct emif_regs ddr3_baltos_emif_reg_data = {
|
|
.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
|
|
.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
|
|
.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
|
|
.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
|
|
.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
|
|
.zq_config = MT41K256M16HA125E_ZQ_CFG,
|
|
.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
|
|
};
|
|
|
|
#ifdef CONFIG_SPL_OS_BOOT
|
|
int spl_start_uboot(void)
|
|
{
|
|
/* break into full u-boot on 'c' */
|
|
return (serial_tstc() && serial_getc() == 'c');
|
|
}
|
|
#endif
|
|
|
|
#define OSC (V_OSCK/1000000)
|
|
const struct dpll_params dpll_ddr = {
|
|
266, OSC-1, 1, -1, -1, -1, -1};
|
|
const struct dpll_params dpll_ddr_evm_sk = {
|
|
303, OSC-1, 1, -1, -1, -1, -1};
|
|
const struct dpll_params dpll_ddr_baltos = {
|
|
400, OSC-1, 1, -1, -1, -1, -1};
|
|
|
|
void am33xx_spl_board_init(void)
|
|
{
|
|
int sil_rev, mpu_vdd;
|
|
int freq;
|
|
|
|
enable_i2c1_pin_mux();
|
|
i2c_set_bus_num(1);
|
|
|
|
freq = am335x_get_efuse_mpu_max_freq(cdev);
|
|
|
|
/*
|
|
* The GP EVM, IDK and EVM SK use a TPS65910 PMIC. For all
|
|
* MPU frequencies we support we use a CORE voltage of
|
|
* 1.1375V. For MPU voltage we need to switch based on
|
|
* the frequency we are running at.
|
|
*/
|
|
if (power_tps65910_init(1))
|
|
return;
|
|
/*
|
|
* Depending on MPU clock and PG we will need a different
|
|
* VDD to drive at that speed.
|
|
*/
|
|
sil_rev = readl(&cdev->deviceid) >> 28;
|
|
mpu_vdd = am335x_get_tps65910_mpu_vdd(sil_rev, freq);
|
|
|
|
/* Tell the TPS65910 to use i2c */
|
|
tps65910_set_i2c_control();
|
|
|
|
/* First update MPU voltage. */
|
|
if (tps65910_voltage_update(MPU, mpu_vdd))
|
|
return;
|
|
|
|
/* Second, update the CORE voltage. */
|
|
if (tps65910_voltage_update(CORE, TPS65910_OP_REG_SEL_1_1_3))
|
|
return;
|
|
|
|
writel(0x000010ff, PRM_DEVICE_INST + 4);
|
|
}
|
|
|
|
const struct dpll_params *get_dpll_ddr_params(void)
|
|
{
|
|
enable_i2c1_pin_mux();
|
|
i2c_set_bus_num(1);
|
|
|
|
return &dpll_ddr_baltos;
|
|
}
|
|
|
|
void set_uart_mux_conf(void)
|
|
{
|
|
enable_uart0_pin_mux();
|
|
}
|
|
|
|
void set_mux_conf_regs(void)
|
|
{
|
|
enable_board_pin_mux();
|
|
}
|
|
|
|
const struct ctrl_ioregs ioregs_baltos = {
|
|
.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
|
|
};
|
|
|
|
void sdram_init(void)
|
|
{
|
|
config_ddr(400, &ioregs_baltos,
|
|
&ddr3_baltos_data,
|
|
&ddr3_baltos_cmd_ctrl_data,
|
|
&ddr3_baltos_emif_reg_data, 0);
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* Basic board specific setup. Pinmux has been handled already.
|
|
*/
|
|
int board_init(void)
|
|
{
|
|
#if defined(CONFIG_HW_WATCHDOG)
|
|
hw_watchdog_init();
|
|
#endif
|
|
|
|
gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100;
|
|
#if defined(CONFIG_NOR) || defined(CONFIG_MTD_RAW_NAND)
|
|
gpmc_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int ft_board_setup(void *blob, struct bd_info *bd)
|
|
{
|
|
int node, ret;
|
|
unsigned char mac_addr[6];
|
|
BSP_VS_HWPARAM header;
|
|
|
|
/* get production data */
|
|
if (read_eeprom(&header))
|
|
return 0;
|
|
|
|
/* setup MAC1 */
|
|
mac_addr[0] = header.MAC1[0];
|
|
mac_addr[1] = header.MAC1[1];
|
|
mac_addr[2] = header.MAC1[2];
|
|
mac_addr[3] = header.MAC1[3];
|
|
mac_addr[4] = header.MAC1[4];
|
|
mac_addr[5] = header.MAC1[5];
|
|
|
|
|
|
node = fdt_path_offset(blob, "ethernet0");
|
|
if (node < 0) {
|
|
printf("no ethernet0 path offset\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6);
|
|
if (ret) {
|
|
printf("error setting mac-address property\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* setup MAC2 */
|
|
mac_addr[0] = header.MAC2[0];
|
|
mac_addr[1] = header.MAC2[1];
|
|
mac_addr[2] = header.MAC2[2];
|
|
mac_addr[3] = header.MAC2[3];
|
|
mac_addr[4] = header.MAC2[4];
|
|
mac_addr[5] = header.MAC2[5];
|
|
|
|
node = fdt_path_offset(blob, "ethernet1");
|
|
if (node < 0) {
|
|
printf("no ethernet1 path offset\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
ret = fdt_setprop(blob, node, "mac-address", &mac_addr, 6);
|
|
if (ret) {
|
|
printf("error setting mac-address property\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
printf("\nFDT was successfully setup\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct module_pin_mux pcie_sw_pin_mux[] = {
|
|
{OFFSET(mii1_rxdv), (MODE(7) | PULLUDEN )}, /* GPIO3_4 */
|
|
{-1},
|
|
};
|
|
|
|
static struct module_pin_mux dip_pin_mux[] = {
|
|
{OFFSET(gpmc_ad12), (MODE(7) | RXACTIVE )}, /* GPIO1_12 */
|
|
{OFFSET(gpmc_ad13), (MODE(7) | RXACTIVE )}, /* GPIO1_13 */
|
|
{OFFSET(gpmc_ad14), (MODE(7) | RXACTIVE )}, /* GPIO1_14 */
|
|
{OFFSET(gpmc_ad15), (MODE(7) | RXACTIVE )}, /* GPIO1_15 */
|
|
{-1},
|
|
};
|
|
|
|
#ifdef CONFIG_BOARD_LATE_INIT
|
|
int board_late_init(void)
|
|
{
|
|
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
|
|
BSP_VS_HWPARAM header;
|
|
char model[4];
|
|
|
|
/* get production data */
|
|
if (read_eeprom(&header)) {
|
|
strcpy(model, "211");
|
|
} else {
|
|
sprintf(model, "%d", header.SystemId);
|
|
if (header.SystemId == 215) {
|
|
configure_module_pin_mux(dip_pin_mux);
|
|
baltos_set_console();
|
|
}
|
|
}
|
|
|
|
/* turn power for the mPCIe slot */
|
|
configure_module_pin_mux(pcie_sw_pin_mux);
|
|
if (gpio_request(MPCIE_SW, "mpcie_sw")) {
|
|
printf("failed to export GPIO %d\n", MPCIE_SW);
|
|
return -ENODEV;
|
|
}
|
|
if (gpio_direction_output(MPCIE_SW, 1)) {
|
|
printf("failed to set GPIO %d direction\n", MPCIE_SW);
|
|
return -ENODEV;
|
|
}
|
|
|
|
env_set("board_name", model);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
|
|
(defined(CONFIG_SPL_ETH) && defined(CONFIG_SPL_BUILD))
|
|
static void cpsw_control(int enabled)
|
|
{
|
|
/* VTP can be added here */
|
|
|
|
return;
|
|
}
|
|
|
|
static struct cpsw_slave_data cpsw_slaves[] = {
|
|
{
|
|
.slave_reg_ofs = 0x208,
|
|
.sliver_reg_ofs = 0xd80,
|
|
.phy_addr = 0,
|
|
},
|
|
{
|
|
.slave_reg_ofs = 0x308,
|
|
.sliver_reg_ofs = 0xdc0,
|
|
.phy_addr = 7,
|
|
},
|
|
};
|
|
|
|
static struct cpsw_platform_data cpsw_data = {
|
|
.mdio_base = CPSW_MDIO_BASE,
|
|
.cpsw_base = CPSW_BASE,
|
|
.mdio_div = 0xff,
|
|
.channels = 8,
|
|
.cpdma_reg_ofs = 0x800,
|
|
.slaves = 2,
|
|
.slave_data = cpsw_slaves,
|
|
.active_slave = 1,
|
|
.ale_reg_ofs = 0xd00,
|
|
.ale_entries = 1024,
|
|
.host_port_reg_ofs = 0x108,
|
|
.hw_stats_reg_ofs = 0x900,
|
|
.bd_ram_ofs = 0x2000,
|
|
.mac_control = (1 << 5),
|
|
.control = cpsw_control,
|
|
.host_port_num = 0,
|
|
.version = CPSW_CTRL_VERSION_2,
|
|
};
|
|
#endif
|
|
|
|
#if ((defined(CONFIG_SPL_ETH) || defined(CONFIG_SPL_USB_ETHER)) \
|
|
&& defined(CONFIG_SPL_BUILD)) || \
|
|
((defined(CONFIG_DRIVER_TI_CPSW) || \
|
|
defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)) && \
|
|
!defined(CONFIG_SPL_BUILD))
|
|
int board_eth_init(struct bd_info *bis)
|
|
{
|
|
int rv, n = 0;
|
|
uint8_t mac_addr[6];
|
|
uint32_t mac_hi, mac_lo;
|
|
|
|
/*
|
|
* Note here that we're using CPSW1 since that has a 1Gbit PHY while
|
|
* CSPW0 has a 100Mbit PHY.
|
|
*
|
|
* On product, CPSW1 maps to port labeled WAN.
|
|
*/
|
|
|
|
/* try reading mac address from efuse */
|
|
mac_lo = readl(&cdev->macid1l);
|
|
mac_hi = readl(&cdev->macid1h);
|
|
mac_addr[0] = mac_hi & 0xFF;
|
|
mac_addr[1] = (mac_hi & 0xFF00) >> 8;
|
|
mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
|
|
mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
|
|
mac_addr[4] = mac_lo & 0xFF;
|
|
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
|
|
|
|
#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
|
|
(defined(CONFIG_SPL_ETH) && defined(CONFIG_SPL_BUILD))
|
|
if (!env_get("ethaddr")) {
|
|
printf("<ethaddr> not set. Validating first E-fuse MAC\n");
|
|
|
|
if (is_valid_ethaddr(mac_addr))
|
|
eth_env_set_enetaddr("ethaddr", mac_addr);
|
|
}
|
|
|
|
#ifdef CONFIG_DRIVER_TI_CPSW
|
|
writel((GMII1_SEL_RMII | GMII2_SEL_RGMII | RGMII2_IDMODE), &cdev->miisel);
|
|
cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RGMII;
|
|
rv = cpsw_register(&cpsw_data);
|
|
if (rv < 0)
|
|
printf("Error %d registering CPSW switch\n", rv);
|
|
else
|
|
n += rv;
|
|
#endif
|
|
|
|
/*
|
|
*
|
|
* CPSW RGMII Internal Delay Mode is not supported in all PVT
|
|
* operating points. So we must set the TX clock delay feature
|
|
* in the AR8051 PHY. Since we only support a single ethernet
|
|
* device in U-Boot, we only do this for the first instance.
|
|
*/
|
|
#define AR8051_PHY_DEBUG_ADDR_REG 0x1d
|
|
#define AR8051_PHY_DEBUG_DATA_REG 0x1e
|
|
#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
|
|
#define AR8051_RGMII_TX_CLK_DLY 0x100
|
|
const char *devname;
|
|
devname = miiphy_get_current_dev();
|
|
|
|
miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_ADDR_REG,
|
|
AR8051_DEBUG_RGMII_CLK_DLY_REG);
|
|
miiphy_write(devname, 0x7, AR8051_PHY_DEBUG_DATA_REG,
|
|
AR8051_RGMII_TX_CLK_DLY);
|
|
#endif
|
|
return n;
|
|
}
|
|
#endif
|