mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-09-22 23:52:03 +00:00
2226ca1734
Now that proper load and execution addresses are set in v1 kwbimage we can use it for loading and booting U-Boot proper. Use the new spl_parse_board_header() function to implement parsing the kwbimage v1 header. Use information from this header to locate offset and size of the U-Boot proper binary, instead of using the legacy U-Boot header which is prepended to the U-Boot proper binary stored at fixed offset. This has the advantage that we do not need to relay on legacy U-Boot header anymore and therefore U-Boot proper binary can be stored at any offset, as is the case when loading & booting U-Boot proper by BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL code anymore. Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case BootROM is used for loading and executing U-Boot proper. This reduces the size of U-Boot's SPL image. By default these config options are enabled and so BootROM loading is not used. In some cases BootROM reads from SPI NOR at lower speed than U-Boot SPL. So people can decide whether they want to have smaller SPL binary at the cost of slower boot. Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO, CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT, CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply" (which can be selectivelly turned off and causes booting via BootROM). Options CONFIG_SYS_SPI_U_BOOT_OFFS, CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to zero as they define the location where kwbimage header starts. It is the location where BootROM expects start of the kwbimage from which it reads, parses and executes SPL part. The same applies to option CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one. Update all config files to set correct values of these options and set CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot proper starts. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> |
||
|---|---|---|
| .. | ||
| clearfog.c | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Update from original Marvell U-Boot to mainline U-Boot:
-------------------------------------------------------
Generate the U-Boot image with these commands:
$ make clearfog_defconfig
$ make
The resulting image including the SPL binary with the
full DDR setup is "u-boot-spl.kwb".
Now all you need to do is copy this image on a SD card.
For example with this command:
$ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1
Please use the correct device node for your setup instead
of "/dev/sdX" here!
Install U-Boot on eMMC:
-----------------------
To make SPL load the main U-Boot image from the eMMC boot partition enable
eMMC boot acknowledgement and boot partition with the following U-Boot
command:
mmc partconf 0 1 1 0
Install U-Boot on eMMC boot partition from Linux running on Clearfog:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=u-boot-spl.kwb of=/dev/mmcblk0boot0
Note that the SD card is not accessible when the Clearfog SOM has eMMC.
Consider initial boot from UART (see below).
Install U-Boot on SATA:
-----------------------
When loading the main U-Boot image from raw SATA sector, set
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR to 0x141.
Boot selection:
---------------
Before powering up the board, boot selection should be done via the SW1 dip
switch (0: OFF, 1: ON):
- SPI: 00010
- SD/eMMC: 00111
- M.2 SSD: 11100
- UART: 01001 [1]
[1]: According to SolidRun's manual, 11110 should be used for UART booting on
the ClearFog 'Pro' variant.
However, this doesn't work (anymore) at least on Rev. 2.1 (but '01001' as
mentionend for the 'Base' variant does).
Boot from UART:
---------------
Connect the on-board micro-USB (CF Pro: CON11, CF Base: CON5)
to your host.
Set the SW1 DIP switches to UART boot (see above).
Run the following command to initiate U-Boot download:
./tools/kwboot -b u-boot-spl.kwb /dev/ttyUSBX
Use the correct UART device node for /dev/ttyUSBX.
When download finishes start your favorite terminal emulator
on /dev/ttyUSBX.