u-boot/board/variscite/dart_6ul
Parthiban Nallathambi d8d33b6d4d imx: Add variscite DART-6UL Evaluation Kit
Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.

CPU:   Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial@02020000
Out:   serial@02020000
Err:   serial@02020000
Net:   FEC0

Working:
 - Eth0
 - i2c
 - MMC/SD
 - eMMC
 - USB host
 - UART 1

Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html

Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
2019-04-25 19:16:24 +02:00
..
dart_6ul.c imx: Add variscite DART-6UL Evaluation Kit 2019-04-25 19:16:24 +02:00
Kconfig imx: Add variscite DART-6UL Evaluation Kit 2019-04-25 19:16:24 +02:00
MAINTAINERS imx: Add variscite DART-6UL Evaluation Kit 2019-04-25 19:16:24 +02:00
Makefile imx: Add variscite DART-6UL Evaluation Kit 2019-04-25 19:16:24 +02:00
README imx: Add variscite DART-6UL Evaluation Kit 2019-04-25 19:16:24 +02:00
spl.c imx: Add variscite DART-6UL Evaluation Kit 2019-04-25 19:16:24 +02:00

How to use U-Boot on variscite DART-6UL Evaluation Kit
------------------------------------------------------

- Configure and build U-Boot for DART-6UL iMX6ULL:

    $ make mrproper
    $ make variscite_dart6ul_defconfig
    $ make

  This will generate SPL and u-boot-dtb.img images.

Boot from MMC/SD:
- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:

    $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync

- Boot mode settings:

  Boot switch position: SW1 -> 0
			SW2 -> 0

Boot from eMMC:
- if bootpart is not enabled by default, to enable under Linux
	echo 0 >/sys/block/mmcblk1boot0/force_ro
	mmc bootpart enable 1 1 /dev/mmcblk1boot0

- Flash the SPL and u-boot-dtb.img to mmcblk1boot0
    $ sudo dd if=SPL of=/dev/mmcblk1boot0 bs=1k seek=1; sync
    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk1boot0 bs=1k seek=69; sync

- Boot mode settings:

  Boot switch position: SW1 -> 0
			SW2 -> 1

- Connect the Serial cable to UART0 and the PC for the console.

- Insert the micro SD card in the board and power it up.

- U-Boot messages should come up.