u-boot/arch/arm/include/asm/arch-omap5/sys_proto.h
pekon gupta 6aff050988 mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00

118 lines
3 KiB
C

/*
* (C) Copyright 2010
* Texas Instruments, <www.ti.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
#include <asm/arch/omap.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/omap_common.h>
#include <linux/mtd/omap_gpmc.h>
#include <asm/arch/clock.h>
DECLARE_GLOBAL_DATA_PTR;
struct pad_conf_entry {
u32 offset;
u32 val;
};
struct omap_sysinfo {
char *board_string;
};
extern const struct omap_sysinfo sysinfo;
void gpmc_init(void);
void watchdog_init(void);
u32 get_device_type(void);
void do_set_mux(u32 base, struct pad_conf_entry const *array, int size);
void set_muxconf_regs_essential(void);
void sr32(void *, u32, u32, u32);
u32 wait_on_value(u32, u32, void *, u32);
void sdelay(unsigned long);
void setup_clocks_for_console(void);
void prcm_init(void);
void bypass_dpll(u32 const base);
void freq_update_core(void);
u32 get_sys_clk_freq(void);
u32 omap5_ddr_clk(void);
void cancel_out(u32 *num, u32 *den, u32 den_limit);
void sdram_init(void);
u32 omap_sdram_size(void);
u32 cortex_rev(void);
void save_omap_boot_params(void);
void init_omap_revision(void);
void do_io_settings(void);
void sri2c_init(void);
void gpi2c_init(void);
int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data);
u32 warm_reset(void);
void force_emif_self_refresh(void);
void get_ioregs(const struct ctrl_ioregs **regs);
void srcomp_enable(void);
void setup_warmreset_time(void);
static inline u32 running_from_sdram(void)
{
u32 pc;
asm volatile ("mov %0, pc" : "=r" (pc));
return ((pc >= OMAP54XX_DRAM_ADDR_SPACE_START) &&
(pc < OMAP54XX_DRAM_ADDR_SPACE_END));
}
static inline u8 uboot_loaded_by_spl(void)
{
/*
* u-boot can be running from sdram either because of configuration
* Header or by SPL. If because of CH, then the romcode sets the
* CHSETTINGS executed bit to true in the boot parameter structure that
* it passes to the bootloader.This parameter is stored in the ch_flags
* variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
* mandatory section if CH is present.
*/
if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
return 0;
else
return running_from_sdram();
}
/*
* The basic hardware init of OMAP(s_init()) can happen in 4
* different contexts:
* 1. SPL running from SRAM
* 2. U-Boot running from FLASH
* 3. Non-XIP U-Boot loaded to SDRAM by SPL
* 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
* Configuration Header feature
*
* This function finds this context.
* Defining as inline may help in compiling out unused functions in SPL
*/
static inline u32 omap_hw_init_context(void)
{
#ifdef CONFIG_SPL_BUILD
return OMAP_INIT_CONTEXT_SPL;
#else
if (uboot_loaded_by_spl())
return OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL;
else if (running_from_sdram())
return OMAP_INIT_CONTEXT_UBOOT_AFTER_CH;
else
return OMAP_INIT_CONTEXT_UBOOT_FROM_NOR;
#endif
}
static inline u32 div_round_up(u32 num, u32 den)
{
return (num + den - 1)/den;
}
static inline u32 usec_to_32k(u32 usec)
{
return div_round_up(32768 * usec, 1000000);
}
#endif