mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 12:33:41 +00:00
a982bbbc1f
Addresses passed on to readl and writel are expected to be of the same size as a pointer. Change the parameter types of sunxi_spi0_read_data() to make the compiler happy and allow a warning-free aarch64 compile. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
287 lines
8.6 KiB
C
287 lines
8.6 KiB
C
/*
|
|
* Copyright (C) 2016 Siarhei Siamashka <siarhei.siamashka@gmail.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <spl.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/io.h>
|
|
|
|
#ifdef CONFIG_SPL_OS_BOOT
|
|
#error CONFIG_SPL_OS_BOOT is not supported yet
|
|
#endif
|
|
|
|
/*
|
|
* This is a very simple U-Boot image loading implementation, trying to
|
|
* replicate what the boot ROM is doing when loading the SPL. Because we
|
|
* know the exact pins where the SPI Flash is connected and also know
|
|
* that the Read Data Bytes (03h) command is supported, the hardware
|
|
* configuration is very simple and we don't need the extra flexibility
|
|
* of the SPI framework. Moreover, we rely on the default settings of
|
|
* the SPI controler hardware registers and only adjust what needs to
|
|
* be changed. This is good for the code size and this implementation
|
|
* adds less than 400 bytes to the SPL.
|
|
*
|
|
* There are two variants of the SPI controller in Allwinner SoCs:
|
|
* A10/A13/A20 (sun4i variant) and everything else (sun6i variant).
|
|
* Both of them are supported.
|
|
*
|
|
* The pin mixing part is SoC specific and only A10/A13/A20/H3/A64 are
|
|
* supported at the moment.
|
|
*/
|
|
|
|
/*****************************************************************************/
|
|
/* SUN4I variant of the SPI controller */
|
|
/*****************************************************************************/
|
|
|
|
#define SUN4I_SPI0_CCTL (0x01C05000 + 0x1C)
|
|
#define SUN4I_SPI0_CTL (0x01C05000 + 0x08)
|
|
#define SUN4I_SPI0_RX (0x01C05000 + 0x00)
|
|
#define SUN4I_SPI0_TX (0x01C05000 + 0x04)
|
|
#define SUN4I_SPI0_FIFO_STA (0x01C05000 + 0x28)
|
|
#define SUN4I_SPI0_BC (0x01C05000 + 0x20)
|
|
#define SUN4I_SPI0_TC (0x01C05000 + 0x24)
|
|
|
|
#define SUN4I_CTL_ENABLE BIT(0)
|
|
#define SUN4I_CTL_MASTER BIT(1)
|
|
#define SUN4I_CTL_TF_RST BIT(8)
|
|
#define SUN4I_CTL_RF_RST BIT(9)
|
|
#define SUN4I_CTL_XCH BIT(10)
|
|
|
|
/*****************************************************************************/
|
|
/* SUN6I variant of the SPI controller */
|
|
/*****************************************************************************/
|
|
|
|
#define SUN6I_SPI0_CCTL (0x01C68000 + 0x24)
|
|
#define SUN6I_SPI0_GCR (0x01C68000 + 0x04)
|
|
#define SUN6I_SPI0_TCR (0x01C68000 + 0x08)
|
|
#define SUN6I_SPI0_FIFO_STA (0x01C68000 + 0x1C)
|
|
#define SUN6I_SPI0_MBC (0x01C68000 + 0x30)
|
|
#define SUN6I_SPI0_MTC (0x01C68000 + 0x34)
|
|
#define SUN6I_SPI0_BCC (0x01C68000 + 0x38)
|
|
#define SUN6I_SPI0_TXD (0x01C68000 + 0x200)
|
|
#define SUN6I_SPI0_RXD (0x01C68000 + 0x300)
|
|
|
|
#define SUN6I_CTL_ENABLE BIT(0)
|
|
#define SUN6I_CTL_MASTER BIT(1)
|
|
#define SUN6I_CTL_SRST BIT(31)
|
|
#define SUN6I_TCR_XCH BIT(31)
|
|
|
|
/*****************************************************************************/
|
|
|
|
#define CCM_AHB_GATING0 (0x01C20000 + 0x60)
|
|
#define CCM_SPI0_CLK (0x01C20000 + 0xA0)
|
|
#define SUN6I_BUS_SOFT_RST_REG0 (0x01C20000 + 0x2C0)
|
|
|
|
#define AHB_RESET_SPI0_SHIFT 20
|
|
#define AHB_GATE_OFFSET_SPI0 20
|
|
|
|
#define SPI0_CLK_DIV_BY_2 0x1000
|
|
#define SPI0_CLK_DIV_BY_4 0x1001
|
|
|
|
/*****************************************************************************/
|
|
|
|
/*
|
|
* Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting
|
|
* from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3.
|
|
*/
|
|
static void spi0_pinmux_setup(unsigned int pin_function)
|
|
{
|
|
unsigned int pin;
|
|
|
|
for (pin = SUNXI_GPC(0); pin <= SUNXI_GPC(2); pin++)
|
|
sunxi_gpio_set_cfgpin(pin, pin_function);
|
|
|
|
if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I))
|
|
sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function);
|
|
else
|
|
sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function);
|
|
}
|
|
|
|
/*
|
|
* Setup 6 MHz from OSC24M (because the BROM is doing the same).
|
|
*/
|
|
static void spi0_enable_clock(void)
|
|
{
|
|
/* Deassert SPI0 reset on SUN6I */
|
|
if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I))
|
|
setbits_le32(SUN6I_BUS_SOFT_RST_REG0,
|
|
(1 << AHB_RESET_SPI0_SHIFT));
|
|
|
|
/* Open the SPI0 gate */
|
|
setbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
|
|
|
|
/* Divide by 4 */
|
|
writel(SPI0_CLK_DIV_BY_4, IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) ?
|
|
SUN6I_SPI0_CCTL : SUN4I_SPI0_CCTL);
|
|
/* 24MHz from OSC24M */
|
|
writel((1 << 31), CCM_SPI0_CLK);
|
|
|
|
if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) {
|
|
/* Enable SPI in the master mode and do a soft reset */
|
|
setbits_le32(SUN6I_SPI0_GCR, SUN6I_CTL_MASTER |
|
|
SUN6I_CTL_ENABLE |
|
|
SUN6I_CTL_SRST);
|
|
/* Wait for completion */
|
|
while (readl(SUN6I_SPI0_GCR) & SUN6I_CTL_SRST)
|
|
;
|
|
} else {
|
|
/* Enable SPI in the master mode and reset FIFO */
|
|
setbits_le32(SUN4I_SPI0_CTL, SUN4I_CTL_MASTER |
|
|
SUN4I_CTL_ENABLE |
|
|
SUN4I_CTL_TF_RST |
|
|
SUN4I_CTL_RF_RST);
|
|
}
|
|
}
|
|
|
|
static void spi0_disable_clock(void)
|
|
{
|
|
/* Disable the SPI0 controller */
|
|
if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I))
|
|
clrbits_le32(SUN6I_SPI0_GCR, SUN6I_CTL_MASTER |
|
|
SUN6I_CTL_ENABLE);
|
|
else
|
|
clrbits_le32(SUN4I_SPI0_CTL, SUN4I_CTL_MASTER |
|
|
SUN4I_CTL_ENABLE);
|
|
|
|
/* Disable the SPI0 clock */
|
|
writel(0, CCM_SPI0_CLK);
|
|
|
|
/* Close the SPI0 gate */
|
|
clrbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
|
|
|
|
/* Assert SPI0 reset on SUN6I */
|
|
if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I))
|
|
clrbits_le32(SUN6I_BUS_SOFT_RST_REG0,
|
|
(1 << AHB_RESET_SPI0_SHIFT));
|
|
}
|
|
|
|
static void spi0_init(void)
|
|
{
|
|
unsigned int pin_function = SUNXI_GPC_SPI0;
|
|
|
|
if (IS_ENABLED(CONFIG_MACH_SUN50I))
|
|
pin_function = SUN50I_GPC_SPI0;
|
|
|
|
spi0_pinmux_setup(pin_function);
|
|
spi0_enable_clock();
|
|
}
|
|
|
|
static void spi0_deinit(void)
|
|
{
|
|
/* New SoCs can disable pins, older could only set them as input */
|
|
unsigned int pin_function = SUNXI_GPIO_INPUT;
|
|
if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I))
|
|
pin_function = SUNXI_GPIO_DISABLE;
|
|
|
|
spi0_disable_clock();
|
|
spi0_pinmux_setup(pin_function);
|
|
}
|
|
|
|
/*****************************************************************************/
|
|
|
|
#define SPI_READ_MAX_SIZE 60 /* FIFO size, minus 4 bytes of the header */
|
|
|
|
static void sunxi_spi0_read_data(u8 *buf, u32 addr, u32 bufsize,
|
|
ulong spi_ctl_reg,
|
|
ulong spi_ctl_xch_bitmask,
|
|
ulong spi_fifo_reg,
|
|
ulong spi_tx_reg,
|
|
ulong spi_rx_reg,
|
|
ulong spi_bc_reg,
|
|
ulong spi_tc_reg,
|
|
ulong spi_bcc_reg)
|
|
{
|
|
writel(4 + bufsize, spi_bc_reg); /* Burst counter (total bytes) */
|
|
writel(4, spi_tc_reg); /* Transfer counter (bytes to send) */
|
|
if (spi_bcc_reg)
|
|
writel(4, spi_bcc_reg); /* SUN6I also needs this */
|
|
|
|
/* Send the Read Data Bytes (03h) command header */
|
|
writeb(0x03, spi_tx_reg);
|
|
writeb((u8)(addr >> 16), spi_tx_reg);
|
|
writeb((u8)(addr >> 8), spi_tx_reg);
|
|
writeb((u8)(addr), spi_tx_reg);
|
|
|
|
/* Start the data transfer */
|
|
setbits_le32(spi_ctl_reg, spi_ctl_xch_bitmask);
|
|
|
|
/* Wait until everything is received in the RX FIFO */
|
|
while ((readl(spi_fifo_reg) & 0x7F) < 4 + bufsize)
|
|
;
|
|
|
|
/* Skip 4 bytes */
|
|
readl(spi_rx_reg);
|
|
|
|
/* Read the data */
|
|
while (bufsize-- > 0)
|
|
*buf++ = readb(spi_rx_reg);
|
|
|
|
/* tSHSL time is up to 100 ns in various SPI flash datasheets */
|
|
udelay(1);
|
|
}
|
|
|
|
static void spi0_read_data(void *buf, u32 addr, u32 len)
|
|
{
|
|
u8 *buf8 = buf;
|
|
u32 chunk_len;
|
|
|
|
while (len > 0) {
|
|
chunk_len = len;
|
|
if (chunk_len > SPI_READ_MAX_SIZE)
|
|
chunk_len = SPI_READ_MAX_SIZE;
|
|
|
|
if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) {
|
|
sunxi_spi0_read_data(buf8, addr, chunk_len,
|
|
SUN6I_SPI0_TCR,
|
|
SUN6I_TCR_XCH,
|
|
SUN6I_SPI0_FIFO_STA,
|
|
SUN6I_SPI0_TXD,
|
|
SUN6I_SPI0_RXD,
|
|
SUN6I_SPI0_MBC,
|
|
SUN6I_SPI0_MTC,
|
|
SUN6I_SPI0_BCC);
|
|
} else {
|
|
sunxi_spi0_read_data(buf8, addr, chunk_len,
|
|
SUN4I_SPI0_CTL,
|
|
SUN4I_CTL_XCH,
|
|
SUN4I_SPI0_FIFO_STA,
|
|
SUN4I_SPI0_TX,
|
|
SUN4I_SPI0_RX,
|
|
SUN4I_SPI0_BC,
|
|
SUN4I_SPI0_TC,
|
|
0);
|
|
}
|
|
|
|
len -= chunk_len;
|
|
buf8 += chunk_len;
|
|
addr += chunk_len;
|
|
}
|
|
}
|
|
|
|
/*****************************************************************************/
|
|
|
|
static int spl_spi_load_image(struct spl_image_info *spl_image,
|
|
struct spl_boot_device *bootdev)
|
|
{
|
|
int err;
|
|
struct image_header *header;
|
|
header = (struct image_header *)(CONFIG_SYS_TEXT_BASE);
|
|
|
|
spi0_init();
|
|
|
|
spi0_read_data((void *)header, CONFIG_SYS_SPI_U_BOOT_OFFS, 0x40);
|
|
err = spl_parse_image_header(spl_image, header);
|
|
if (err)
|
|
return err;
|
|
|
|
spi0_read_data((void *)spl_image->load_addr, CONFIG_SYS_SPI_U_BOOT_OFFS,
|
|
spl_image->size);
|
|
|
|
spi0_deinit();
|
|
return 0;
|
|
}
|
|
/* Use priorty 0 to override the default if it happens to be linked in */
|
|
SPL_LOAD_IMAGE_METHOD("sunxi SPI", 0, BOOT_DEVICE_SPI, spl_spi_load_image);
|