mirror of
https://github.com/AsahiLinux/u-boot
synced 2025-01-06 02:08:59 +00:00
56d2050f40
Add DEK blob encapsulation support for IMX8M through "dek_blob" command. On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob for encrypted boot. The DEK blob is encapsulated by OP-TEE through a trusted application call. U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE dynamic shared memory. To enable the DEK blob encapsulation, add to the defconfig: CONFIG_SECURE_BOOT=y CONFIG_FAT_WRITE=y CONFIG_CMD_DEKBLOB=y Signed-off-by: Clement Faure <clement.faure@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
153 lines
1.5 KiB
Text
153 lines
1.5 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2019 NXP
|
|
*/
|
|
|
|
/ {
|
|
wdt-reboot {
|
|
compatible = "wdt-reboot";
|
|
wdt = <&wdog1>;
|
|
u-boot,dm-spl;
|
|
};
|
|
firmware {
|
|
optee {
|
|
compatible = "linaro,optee-tz";
|
|
method = "smc";
|
|
};
|
|
};
|
|
};
|
|
|
|
&{/soc@0} {
|
|
u-boot,dm-pre-reloc;
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&clk {
|
|
u-boot,dm-spl;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&osc_32k {
|
|
u-boot,dm-spl;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&osc_24m {
|
|
u-boot,dm-spl;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&aips1 {
|
|
u-boot,dm-spl;
|
|
u-boot,dm-pre-reloc;
|
|
};
|
|
|
|
&aips2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&aips3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&iomuxc {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
®_usdhc2_vmmc {
|
|
u-boot,off-on-delay-us = <20000>;
|
|
};
|
|
|
|
®_usdhc2_vmmc {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_uart2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc2_gpio {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&pinctrl_usdhc3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio4 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&gpio5 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&uart2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&i2c1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&i2c2 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&i2c3 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&i2c4 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&i2c5 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&i2c6 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usdhc1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&usdhc2 {
|
|
u-boot,dm-spl;
|
|
sd-uhs-sdr104;
|
|
sd-uhs-ddr50;
|
|
};
|
|
|
|
&usdhc3 {
|
|
u-boot,dm-spl;
|
|
mmc-hs400-1_8v;
|
|
mmc-hs400-enhanced-strobe;
|
|
};
|
|
|
|
&wdog1 {
|
|
u-boot,dm-spl;
|
|
};
|
|
|
|
&fec {
|
|
phy-reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
|
|
phy-reset-duration = <15>;
|
|
phy-reset-post-delay = <100>;
|
|
};
|