u-boot/board/gateworks/gw_ventana/gw_ventana.c
Tim Harvey 59189a8b26 ventana: Add Gateworks Ventana family support
Gateworks Ventana is a product family based on the i.MX6.  This
patch adds support for all boards in the Ventana family. Where
possible, data from the boards EEPROM is used to determine various
details about the board at runtime.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-03-12 10:23:03 +01:00

1263 lines
33 KiB
C

/*
* Copyright (C) 2013 Gateworks Corporation
*
* Author: Tim Harvey <tharvey@gateworks.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/sata.h>
#include <jffs2/load_kernel.h>
#include <hwconfig.h>
#include <i2c.h>
#include <linux/ctype.h>
#include <fdt_support.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <mmc.h>
#include <mtd_node.h>
#include <netdev.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
#include <i2c.h>
#include <fdt_support.h>
#include <jffs2/load_kernel.h>
#include <spi_flash.h>
#include "gsc.h"
#include "ventana_eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
/* GPIO's common to all baseboards */
#define GP_PHY_RST IMX_GPIO_NR(1, 30)
#define GP_USB_OTG_PWR IMX_GPIO_NR(3, 22)
#define GP_SD3_CD IMX_GPIO_NR(7, 0)
#define GP_RS232_EN IMX_GPIO_NR(2, 11)
#define GP_MSATA_SEL IMX_GPIO_NR(2, 8)
/* I2C bus numbers */
#define I2C_GSC 0
#define I2C_PMIC 1
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define SPI_PAD_CTRL (PAD_CTL_HYS | \
PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
#define DIO_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST)
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
/*
* EEPROM board info struct populated by read_eeprom so that we only have to
* read it once.
*/
static struct ventana_board_info ventana_info;
enum {
GW54proto, /* original GW5400-A prototype */
GW51xx,
GW52xx,
GW53xx,
GW54xx,
GW_UNKNOWN,
};
int board_type;
/* UART1: Function varies per baseboard */
iomux_v3_cfg_t const uart1_pads[] = {
MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
/* UART2: Serial Console */
iomux_v3_cfg_t const uart2_pads[] = {
MX6_PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
MX6_PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
/* I2C1: GSC */
struct i2c_pads_info i2c_pad_info0 = {
.scl = {
.i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC,
.gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC,
.gp = IMX_GPIO_NR(3, 21)
},
.sda = {
.i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC,
.gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC,
.gp = IMX_GPIO_NR(3, 28)
}
};
/* I2C2: PMIC/PCIe Switch/PCIe Clock/Mezz */
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC,
.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC,
.gp = IMX_GPIO_NR(4, 12)
},
.sda = {
.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
.gp = IMX_GPIO_NR(4, 13)
}
};
/* I2C3: Misc/Expansion */
struct i2c_pads_info i2c_pad_info2 = {
.scl = {
.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC,
.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC,
.gp = IMX_GPIO_NR(1, 3)
},
.sda = {
.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
.gp = IMX_GPIO_NR(1, 6)
}
};
/* MMC */
iomux_v3_cfg_t const usdhc3_pads[] = {
MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
};
/* ENET */
iomux_v3_cfg_t const enet_pads[] = {
MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
/* PHY nRST */
MX6_PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
/* NAND */
iomux_v3_cfg_t const nfc_pads[] = {
MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
#ifdef CONFIG_CMD_NAND
static void setup_gpmi_nand(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* config gpmi nand iomux */
imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
/* config gpmi and bch clock to 100 MHz */
clrsetbits_le32(&mxc_ccm->cs2cdr,
MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
/* enable gpmi and bch clock gating */
setbits_le32(&mxc_ccm->CCGR4,
MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
/* enable apbh clock gating */
setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
}
#endif
static void setup_iomux_enet(void)
{
imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
/* toggle PHY_RST# */
gpio_direction_output(GP_PHY_RST, 0);
mdelay(2);
gpio_set_value(GP_PHY_RST, 1);
}
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
}
#ifdef CONFIG_USB_EHCI_MX6
iomux_v3_cfg_t const usb_pads[] = {
MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(DIO_PAD_CTRL),
MX6_PAD_KEY_COL4__USB_OTG_OC | MUX_PAD_CTRL(DIO_PAD_CTRL),
MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(DIO_PAD_CTRL), /* OTG PWR */
};
int board_ehci_hcd_init(int port)
{
struct ventana_board_info *info = &ventana_info;
imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads));
/* Reset USB HUB (present on GW54xx/GW53xx) */
switch (info->model[3]) {
case '3': /* GW53xx */
imx_iomux_v3_setup_pad(MX6_PAD_GPIO_9__GPIO1_IO09|
MUX_PAD_CTRL(NO_PAD_CTRL));
gpio_direction_output(IMX_GPIO_NR(1, 9), 0);
mdelay(2);
gpio_set_value(IMX_GPIO_NR(1, 9), 1);
break;
case '4': /* GW54xx */
imx_iomux_v3_setup_pad(MX6_PAD_SD1_DAT0__GPIO1_IO16 |
MUX_PAD_CTRL(NO_PAD_CTRL));
gpio_direction_output(IMX_GPIO_NR(1, 16), 0);
mdelay(2);
gpio_set_value(IMX_GPIO_NR(1, 16), 1);
break;
}
return 0;
}
int board_ehci_power(int port, int on)
{
if (port)
return 0;
gpio_set_value(GP_USB_OTG_PWR, on);
return 0;
}
#endif /* CONFIG_USB_EHCI_MX6 */
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg usdhc_cfg = { USDHC3_BASE_ADDR };
int board_mmc_getcd(struct mmc *mmc)
{
/* Card Detect */
gpio_direction_input(GP_SD3_CD);
return !gpio_get_value(GP_SD3_CD);
}
int board_mmc_init(bd_t *bis)
{
/* Only one USDHC controller on Ventana */
imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
usdhc_cfg.max_bus_width = 4;
return fsl_esdhc_initialize(bis, &usdhc_cfg);
}
#endif /* CONFIG_FSL_ESDHC */
#ifdef CONFIG_MXC_SPI
iomux_v3_cfg_t const ecspi1_pads[] = {
/* SS1 */
MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
};
static void setup_spi(void)
{
gpio_direction_output(CONFIG_SF_DEFAULT_CS, 1);
imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
ARRAY_SIZE(ecspi1_pads));
}
#endif
/* configure eth0 PHY board-specific LED behavior */
int board_phy_config(struct phy_device *phydev)
{
unsigned short val;
/* Marvel 88E1510 */
if (phydev->phy_id == 0x1410dd1) {
/*
* Page 3, Register 16: LED[2:0] Function Control Register
* LED[0] (SPD:Amber) R16_3.3:0 to 0111: on-GbE link
* LED[1] (LNK:Green) R16_3.7:4 to 0001: on-link, blink-activity
*/
phy_write(phydev, MDIO_DEVAD_NONE, 22, 3);
val = phy_read(phydev, MDIO_DEVAD_NONE, 16);
val &= 0xff00;
val |= 0x0017;
phy_write(phydev, MDIO_DEVAD_NONE, 16, val);
phy_write(phydev, MDIO_DEVAD_NONE, 22, 0);
}
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
int board_eth_init(bd_t *bis)
{
setup_iomux_enet();
#ifdef CONFIG_FEC_MXC
cpu_eth_init(bis);
#endif
#ifdef CONFIG_CI_UDC
/* For otg ethernet*/
usb_eth_initialize(bis);
#endif
return 0;
}
/* read ventana EEPROM, check for validity, and return baseboard type */
static int
read_eeprom(void)
{
int i;
int chksum;
char baseboard;
int type;
struct ventana_board_info *info = &ventana_info;
unsigned char *buf = (unsigned char *)&ventana_info;
memset(info, 0, sizeof(ventana_info));
/*
* On a board with a missing/depleted backup battery for GSC, the
* board may be ready to probe the GSC before its firmware is
* running. We will wait here indefinately for the GSC/EEPROM.
*/
while (1) {
if (0 == i2c_set_bus_num(I2C_GSC) &&
0 == i2c_probe(GSC_EEPROM_ADDR))
break;
mdelay(1);
}
/* read eeprom config section */
if (gsc_i2c_read(GSC_EEPROM_ADDR, 0x00, 1, buf, sizeof(ventana_info))) {
puts("EEPROM: Failed to read EEPROM\n");
info->model[0] = 0;
return GW_UNKNOWN;
}
/* sanity checks */
if (info->model[0] != 'G' || info->model[1] != 'W') {
puts("EEPROM: Invalid Model in EEPROM\n");
info->model[0] = 0;
return GW_UNKNOWN;
}
/* validate checksum */
for (chksum = 0, i = 0; i < sizeof(*info)-2; i++)
chksum += buf[i];
if ((info->chksum[0] != chksum>>8) ||
(info->chksum[1] != (chksum&0xff))) {
puts("EEPROM: Failed EEPROM checksum\n");
info->model[0] = 0;
return GW_UNKNOWN;
}
/* original GW5400-A prototype */
baseboard = info->model[3];
if (strncasecmp((const char *)info->model, "GW5400-A", 8) == 0)
baseboard = '0';
switch (baseboard) {
case '0': /* original GW5400-A prototype */
type = GW54proto;
break;
case '1':
type = GW51xx;
break;
case '2':
type = GW52xx;
break;
case '3':
type = GW53xx;
break;
case '4':
type = GW54xx;
break;
default:
printf("EEPROM: Unknown model in EEPROM: %s\n", info->model);
type = GW_UNKNOWN;
break;
}
return type;
}
/*
* Baseboard specific GPIO
*/
/* common to add baseboards */
static iomux_v3_cfg_t const gw_gpio_pads[] = {
/* MSATA_EN */
MX6_PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* RS232_EN# */
MX6_PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
/* prototype */
static iomux_v3_cfg_t const gwproto_gpio_pads[] = {
/* PANLEDG# */
MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PANLEDR# */
MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* LOCLED# */
MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* RS485_EN */
MX6_PAD_SD3_DAT4__GPIO7_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_PWREN# */
MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_IRQ# */
MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* VID_EN */
MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* DIOI2C_DIS# */
MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PCICK_SSON */
MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PCI_RST# */
MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const gw51xx_gpio_pads[] = {
/* PANLEDG# */
MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PANLEDR# */
MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_PWREN# */
MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_IRQ# */
MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* GPS_SHDN */
MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* VID_PWR */
MX6_PAD_CSI0_DATA_EN__GPIO5_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PCI_RST# */
MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const gw52xx_gpio_pads[] = {
/* PANLEDG# */
MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PANLEDR# */
MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_PWREN# */
MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_IRQ# */
MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* MX6_LOCLED# */
MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* GPS_SHDN */
MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* USBOTG_SEL */
MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* VID_PWR */
MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PCI_RST# */
MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const gw53xx_gpio_pads[] = {
/* PANLEDG# */
MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PANLEDR# */
MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_PWREN# */
MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_IRQ# */
MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* MX6_LOCLED# */
MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* GPS_SHDN */
MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* VID_EN */
MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PCI_RST# */
MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const gw54xx_gpio_pads[] = {
/* PANLEDG# */
MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PANLEDR# */
MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* MX6_LOCLED# */
MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* MIPI_DIO */
MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* RS485_EN */
MX6_PAD_EIM_D24__GPIO3_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_PWREN# */
MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* IOEXP_IRQ# */
MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* DIOI2C_DIS# */
MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* DIOI2C_DIS# */
MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PCICK_SSON */
MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* PCI_RST# */
MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
/*
* each baseboard has 4 user configurable Digital IO lines which can
* be pinmuxed as a GPIO or in some cases a PWM
*/
struct dio_cfg {
iomux_v3_cfg_t gpio_padmux;
unsigned gpio_param;
iomux_v3_cfg_t pwm_padmux;
unsigned pwm_param;
};
struct ventana {
/* pinmux */
iomux_v3_cfg_t const *gpio_pads;
int num_pads;
/* DIO pinmux/val */
struct dio_cfg dio_cfg[4];
/* various gpios (0 if non-existent) */
int leds[3];
int pcie_rst;
int mezz_pwren;
int mezz_irq;
int rs485en;
int gps_shdn;
int vidin_en;
int dioi2c_en;
int pcie_sson;
int usb_sel;
};
struct ventana gpio_cfg[] = {
/* GW5400proto */
{
.gpio_pads = gw54xx_gpio_pads,
.num_pads = ARRAY_SIZE(gw54xx_gpio_pads),
.dio_cfg = {
{ MX6_PAD_GPIO_9__GPIO1_IO09, IMX_GPIO_NR(1, 9),
MX6_PAD_GPIO_9__PWM1_OUT, 1 },
{ MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
{ MX6_PAD_SD4_DAT1__GPIO2_IO09, IMX_GPIO_NR(2, 9),
MX6_PAD_SD4_DAT1__PWM3_OUT, 3 },
{ MX6_PAD_SD4_DAT2__GPIO2_IO10, IMX_GPIO_NR(2, 10),
MX6_PAD_SD4_DAT2__PWM4_OUT, 4 },
},
.leds = {
IMX_GPIO_NR(4, 6),
IMX_GPIO_NR(4, 10),
IMX_GPIO_NR(4, 15),
},
.pcie_rst = IMX_GPIO_NR(1, 29),
.mezz_pwren = IMX_GPIO_NR(4, 7),
.mezz_irq = IMX_GPIO_NR(4, 9),
.rs485en = IMX_GPIO_NR(3, 24),
.dioi2c_en = IMX_GPIO_NR(4, 5),
.pcie_sson = IMX_GPIO_NR(1, 20),
},
/* GW51xx */
{
.gpio_pads = gw51xx_gpio_pads,
.num_pads = ARRAY_SIZE(gw51xx_gpio_pads),
.dio_cfg = {
{ MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16),
0, 0 },
{ MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
{ MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17),
MX6_PAD_SD1_DAT1__PWM3_OUT, 3 },
{ MX6_PAD_SD1_CMD__GPIO1_IO18, IMX_GPIO_NR(1, 18),
MX6_PAD_SD1_CMD__PWM4_OUT, 4 },
},
.leds = {
IMX_GPIO_NR(4, 6),
IMX_GPIO_NR(4, 10),
},
.pcie_rst = IMX_GPIO_NR(1, 0),
.mezz_pwren = IMX_GPIO_NR(2, 19),
.mezz_irq = IMX_GPIO_NR(2, 18),
.gps_shdn = IMX_GPIO_NR(1, 2),
.vidin_en = IMX_GPIO_NR(5, 20),
},
/* GW52xx */
{
.gpio_pads = gw52xx_gpio_pads,
.num_pads = ARRAY_SIZE(gw52xx_gpio_pads),
.dio_cfg = {
{ MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16),
0, 0 },
{ MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
{ MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17),
MX6_PAD_SD1_DAT1__PWM3_OUT, 3 },
{ MX6_PAD_SD1_CLK__GPIO1_IO20, IMX_GPIO_NR(1, 20),
0, 0 },
},
.leds = {
IMX_GPIO_NR(4, 6),
IMX_GPIO_NR(4, 7),
IMX_GPIO_NR(4, 15),
},
.pcie_rst = IMX_GPIO_NR(1, 29),
.mezz_pwren = IMX_GPIO_NR(2, 19),
.mezz_irq = IMX_GPIO_NR(2, 18),
.gps_shdn = IMX_GPIO_NR(1, 27),
.vidin_en = IMX_GPIO_NR(3, 31),
.usb_sel = IMX_GPIO_NR(1, 2),
},
/* GW53xx */
{
.gpio_pads = gw53xx_gpio_pads,
.num_pads = ARRAY_SIZE(gw53xx_gpio_pads),
.dio_cfg = {
{ MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16),
0, 0 },
{ MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
{ MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17),
MX6_PAD_SD1_DAT1__PWM3_OUT, 3 },
{ MX6_PAD_SD1_CLK__GPIO1_IO20, IMX_GPIO_NR(1, 20),
0, 0 },
},
.leds = {
IMX_GPIO_NR(4, 6),
IMX_GPIO_NR(4, 7),
IMX_GPIO_NR(4, 15),
},
.pcie_rst = IMX_GPIO_NR(1, 29),
.mezz_pwren = IMX_GPIO_NR(2, 19),
.mezz_irq = IMX_GPIO_NR(2, 18),
.gps_shdn = IMX_GPIO_NR(1, 27),
.vidin_en = IMX_GPIO_NR(3, 31),
},
/* GW54xx */
{
.gpio_pads = gw54xx_gpio_pads,
.num_pads = ARRAY_SIZE(gw54xx_gpio_pads),
.dio_cfg = {
{ MX6_PAD_GPIO_9__GPIO1_IO09, IMX_GPIO_NR(1, 9),
MX6_PAD_GPIO_9__PWM1_OUT, 1 },
{ MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
{ MX6_PAD_SD4_DAT1__GPIO2_IO09, IMX_GPIO_NR(2, 9),
MX6_PAD_SD4_DAT1__PWM3_OUT, 3 },
{ MX6_PAD_SD4_DAT2__GPIO2_IO10, IMX_GPIO_NR(2, 10),
MX6_PAD_SD4_DAT2__PWM4_OUT, 4 },
},
.leds = {
IMX_GPIO_NR(4, 6),
IMX_GPIO_NR(4, 7),
IMX_GPIO_NR(4, 15),
},
.pcie_rst = IMX_GPIO_NR(1, 29),
.mezz_pwren = IMX_GPIO_NR(2, 19),
.mezz_irq = IMX_GPIO_NR(2, 18),
.rs485en = IMX_GPIO_NR(7, 1),
.vidin_en = IMX_GPIO_NR(3, 31),
.dioi2c_en = IMX_GPIO_NR(4, 5),
.pcie_sson = IMX_GPIO_NR(1, 20),
},
};
/* setup GPIO pinmux and default configuration per baseboard */
static void setup_board_gpio(int board)
{
struct ventana_board_info *info = &ventana_info;
const char *s;
char arg[10];
size_t len;
int i;
int quiet = simple_strtol(getenv("quiet"), NULL, 10);
if (board >= GW_UNKNOWN)
return;
/* RS232_EN# */
gpio_direction_output(GP_RS232_EN, (hwconfig("rs232")) ? 0 : 1);
/* MSATA Enable */
if (is_cpu_type(MXC_CPU_MX6Q) &&
test_bit(EECONFIG_SATA, info->config)) {
gpio_direction_output(GP_MSATA_SEL,
(hwconfig("msata")) ? 1 : 0);
} else {
gpio_direction_output(GP_MSATA_SEL, 0);
}
/*
* assert PCI_RST# (released by OS when clock is valid)
* TODO: figure out why leaving this de-asserted from PCI scan on boot
* causes linux pcie driver to hang during enumeration
*/
gpio_direction_output(gpio_cfg[board].pcie_rst, 0);
/* turn off (active-high) user LED's */
for (i = 0; i < 4; i++) {
if (gpio_cfg[board].leds[i])
gpio_direction_output(gpio_cfg[board].leds[i], 1);
}
/* Expansion Mezzanine IO */
gpio_direction_output(gpio_cfg[board].mezz_pwren, 0);
gpio_direction_input(gpio_cfg[board].mezz_irq);
/* RS485 Transmit Enable */
if (gpio_cfg[board].rs485en)
gpio_direction_output(gpio_cfg[board].rs485en, 0);
/* GPS_SHDN */
if (gpio_cfg[board].gps_shdn)
gpio_direction_output(gpio_cfg[board].gps_shdn, 1);
/* Analog video codec power enable */
if (gpio_cfg[board].vidin_en)
gpio_direction_output(gpio_cfg[board].vidin_en, 1);
/* DIOI2C_DIS# */
if (gpio_cfg[board].dioi2c_en)
gpio_direction_output(gpio_cfg[board].dioi2c_en, 0);
/* PCICK_SSON: disable spread-spectrum clock */
if (gpio_cfg[board].pcie_sson)
gpio_direction_output(gpio_cfg[board].pcie_sson, 0);
/* USBOTG Select (PCISKT or FrontPanel) */
if (gpio_cfg[board].usb_sel)
gpio_direction_output(gpio_cfg[board].usb_sel, 0);
/*
* Configure DIO pinmux/padctl registers
* see IMX6DQRM/IMX6SDLRM IOMUXC_SW_PAD_CTL_PAD_* register definitions
*/
for (i = 0; i < 4; i++) {
struct dio_cfg *cfg = &gpio_cfg[board].dio_cfg[i];
unsigned ctrl = DIO_PAD_CTRL;
sprintf(arg, "dio%d", i);
if (!hwconfig(arg))
continue;
s = hwconfig_subarg(arg, "padctrl", &len);
if (s)
ctrl = simple_strtoul(s, NULL, 16) & 0x3ffff;
if (hwconfig_subarg_cmp(arg, "mode", "gpio")) {
if (!quiet) {
printf("DIO%d: GPIO%d_IO%02d (gpio-%d)\n", i,
(cfg->gpio_param/32)+1,
cfg->gpio_param%32,
cfg->gpio_param);
}
imx_iomux_v3_setup_pad(cfg->gpio_padmux |
MUX_PAD_CTRL(ctrl));
gpio_direction_input(cfg->gpio_param);
} else if (hwconfig_subarg_cmp("dio2", "mode", "pwm") &&
cfg->pwm_padmux) {
if (!quiet)
printf("DIO%d: pwm%d\n", i, cfg->pwm_param);
imx_iomux_v3_setup_pad(cfg->pwm_padmux |
MUX_PAD_CTRL(ctrl));
}
}
if (!quiet) {
if (is_cpu_type(MXC_CPU_MX6Q) &&
(test_bit(EECONFIG_SATA, info->config))) {
printf("MSATA: %s\n", (hwconfig("msata") ?
"enabled" : "disabled"));
}
printf("RS232: %s\n", (hwconfig("rs232")) ?
"enabled" : "disabled");
}
}
#if defined(CONFIG_CMD_PCI)
int imx6_pcie_toggle_reset(void)
{
if (board_type < GW_UNKNOWN) {
gpio_direction_output(gpio_cfg[board_type].pcie_rst, 0);
mdelay(50);
gpio_direction_output(gpio_cfg[board_type].pcie_rst, 1);
}
return 0;
}
#endif /* CONFIG_CMD_PCI */
#ifdef CONFIG_SERIAL_TAG
/*
* called when setting up ATAGS before booting kernel
* populate serialnum from the following (in order of priority):
* serial# env var
* eeprom
*/
void get_board_serial(struct tag_serialnr *serialnr)
{
char *serial = getenv("serial#");
if (serial) {
serialnr->high = 0;
serialnr->low = simple_strtoul(serial, NULL, 10);
} else if (ventana_info.model[0]) {
serialnr->high = 0;
serialnr->low = ventana_info.serial;
} else {
serialnr->high = 0;
serialnr->low = 0;
}
}
#endif
/*
* Board Support
*/
int board_early_init_f(void)
{
setup_iomux_uart();
gpio_direction_output(GP_USB_OTG_PWR, 0); /* OTG power off */
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
CONFIG_DDR_MB*1024*1024);
return 0;
}
int board_init(void)
{
struct iomuxc_base_regs *const iomuxc_regs
= (struct iomuxc_base_regs *)IOMUXC_BASE_ADDR;
clrsetbits_le32(&iomuxc_regs->gpr[1],
IOMUXC_GPR1_OTG_ID_MASK,
IOMUXC_GPR1_OTG_ID_GPIO1);
/* address of linux boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_CMD_NAND
setup_gpmi_nand();
#endif
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
#ifdef CONFIG_CMD_SATA
setup_sata();
#endif
/* read Gateworks EEPROM into global struct (used later) */
board_type = read_eeprom();
/* board-specifc GPIO iomux */
if (board_type < GW_UNKNOWN) {
imx_iomux_v3_setup_multiple_pads(gw_gpio_pads,
ARRAY_SIZE(gw_gpio_pads));
imx_iomux_v3_setup_multiple_pads(gpio_cfg[board_type].gpio_pads,
gpio_cfg[board_type].num_pads);
}
return 0;
}
#if defined(CONFIG_DISPLAY_BOARDINFO_LATE)
/*
* called during late init (after relocation and after board_init())
* by virtue of CONFIG_DISPLAY_BOARDINFO_LATE as we needed i2c initialized and
* EEPROM read.
*/
int checkboard(void)
{
struct ventana_board_info *info = &ventana_info;
unsigned char buf[4];
const char *p;
int quiet; /* Quiet or minimal output mode */
quiet = 0;
p = getenv("quiet");
if (p)
quiet = simple_strtol(p, NULL, 10);
else
setenv("quiet", "0");
puts("\nGateworks Corporation Copyright 2014\n");
if (info->model[0]) {
printf("Model: %s\n", info->model);
printf("MFGDate: %02x-%02x-%02x%02x\n",
info->mfgdate[0], info->mfgdate[1],
info->mfgdate[2], info->mfgdate[3]);
printf("Serial:%d\n", info->serial);
} else {
puts("Invalid EEPROM - board will not function fully\n");
}
if (quiet)
return 0;
/* Display GSC firmware revision/CRC/status */
i2c_set_bus_num(I2C_GSC);
if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_FWVER, 1, buf, 1)) {
printf("GSC: v%d", buf[0]);
if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_STATUS, 1, buf, 4)) {
printf(" 0x%04x", buf[2] | buf[3]<<8); /* CRC */
printf(" 0x%02x", buf[0]); /* irq status */
}
puts("\n");
}
/* Display RTC */
if (!gsc_i2c_read(GSC_RTC_ADDR, 0x00, 1, buf, 4)) {
printf("RTC: %d\n",
buf[0] | buf[1]<<8 | buf[2]<<16 | buf[3]<<24);
}
return 0;
}
#endif
#ifdef CONFIG_CMD_BMODE
/*
* BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4
* see Table 8-11 and Table 5-9
* BOOT_CFG1[7] = 1 (boot from NAND)
* BOOT_CFG1[5] = 0 - raw NAND
* BOOT_CFG1[4] = 0 - default pad settings
* BOOT_CFG1[3:2] = 00 - devices = 1
* BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3
* BOOT_CFG2[4:3] = 00 - Boot Search Count = 2
* BOOT_CFG2[2:1] = 01 - Pages In Block = 64
* BOOT_CFG2[0] = 0 - Reset time 12ms
*/
static const struct boot_mode board_boot_modes[] = {
/* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */
{ "nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00) },
{ NULL, 0 },
};
#endif
/* late init */
int misc_init_r(void)
{
struct ventana_board_info *info = &ventana_info;
unsigned char reg;
/* set env vars based on EEPROM data */
if (ventana_info.model[0]) {
char str[16], fdt[36];
char *p;
const char *cputype = "";
int i;
/*
* FDT name will be prefixed with CPU type. Three versions
* will be created each increasingly generic and bootloader
* env scripts will try loading each from most specific to
* least.
*/
if (is_cpu_type(MXC_CPU_MX6Q))
cputype = "imx6q";
else if (is_cpu_type(MXC_CPU_MX6DL))
cputype = "imx6dl";
memset(str, 0, sizeof(str));
for (i = 0; i < (sizeof(str)-1) && info->model[i]; i++)
str[i] = tolower(info->model[i]);
if (!getenv("model"))
setenv("model", str);
if (!getenv("fdt_file")) {
sprintf(fdt, "%s-%s.dtb", cputype, str);
setenv("fdt_file", fdt);
}
p = strchr(str, '-');
if (p) {
*p++ = 0;
setenv("model_base", str);
if (!getenv("fdt_file1")) {
sprintf(fdt, "%s-%s.dtb", cputype, str);
setenv("fdt_file1", fdt);
}
str[4] = 'x';
str[5] = 'x';
str[6] = 0;
if (!getenv("fdt_file2")) {
sprintf(fdt, "%s-%s.dtb", cputype, str);
setenv("fdt_file2", fdt);
}
}
/* initialize env from EEPROM */
if (test_bit(EECONFIG_ETH0, info->config) &&
!getenv("ethaddr")) {
eth_setenv_enetaddr("ethaddr", info->mac0);
}
if (test_bit(EECONFIG_ETH1, info->config) &&
!getenv("eth1addr")) {
eth_setenv_enetaddr("eth1addr", info->mac1);
}
/* board serial-number */
sprintf(str, "%6d", info->serial);
setenv("serial#", str);
}
/* configure PFUZE100 PMIC (not used on all Ventana baseboards) */
if ((board_type == GW54xx || board_type == GW54proto) &&
!pmic_init(I2C_PMIC)) {
struct pmic *p = pmic_get("PFUZE100_PMIC");
u32 reg;
if (p && !pmic_probe(p)) {
pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
/* Set VGEN1 to 1.5V and enable */
pmic_reg_read(p, PFUZE100_VGEN1VOL, &reg);
reg &= ~(LDO_VOL_MASK);
reg |= (LDOA_1_50V | LDO_EN);
pmic_reg_write(p, PFUZE100_VGEN1VOL, reg);
/* Set SWBST to 5.0V and enable */
pmic_reg_read(p, PFUZE100_SWBSTCON1, &reg);
reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK);
reg |= (SWBST_5_00V | SWBST_MODE_AUTO);
pmic_reg_write(p, PFUZE100_SWBSTCON1, reg);
}
}
/* setup baseboard specific GPIO pinmux and config */
setup_board_gpio(board_type);
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
/*
* The Gateworks System Controller implements a boot
* watchdog (always enabled) as a workaround for IMX6 boot related
* errata such as:
* ERR005768 - no fix
* ERR006282 - fixed in silicon r1.3
* ERR007117 - fixed in silicon r1.3
* ERR007220 - fixed in silicon r1.3
* see http://cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf
*
* Disable the boot watchdog and display/clear the timeout flag if set
*/
i2c_set_bus_num(I2C_GSC);
if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1)) {
reg |= (1 << GSC_SC_CTRL1_WDDIS);
if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1))
puts("Error: could not disable GSC Watchdog\n");
} else {
puts("Error: could not disable GSC Watchdog\n");
}
if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_STATUS, 1, &reg, 1)) {
if (reg & (1 << GSC_SC_IRQ_WATCHDOG)) { /* watchdog timeout */
puts("GSC boot watchdog timeout detected");
reg &= ~(1 << GSC_SC_IRQ_WATCHDOG); /* clear flag */
gsc_i2c_write(GSC_SC_ADDR, GSC_SC_STATUS, 1, &reg, 1);
}
}
return 0;
}
#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
/* FDT aliases associated with EEPROM config bits */
const char *fdt_aliases[] = {
"ethernet0",
"ethernet1",
"hdmi_out",
"ahci0",
"pcie",
"ssi0",
"ssi1",
"lcd0",
"lvds0",
"lvds1",
"usb0",
"usb1",
"mmc0",
"mmc1",
"mmc2",
"mmc3",
"uart0",
"uart1",
"uart2",
"uart3",
"uart4",
"ipu0",
"ipu1",
"can0",
"mipi_dsi",
"mipi_csi",
"tzasc0",
"tzasc1",
"i2c0",
"i2c1",
"i2c2",
"vpu",
"csi0",
"csi1",
"caam",
NULL,
NULL,
NULL,
NULL,
NULL,
"spi0",
"spi1",
"spi2",
"spi3",
"spi4",
"spi5",
NULL,
NULL,
"pps",
NULL,
NULL,
NULL,
"hdmi_in",
"cvbs_out",
"cvbs_in",
"nand",
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
NULL,
};
/*
* called prior to booting kernel or by 'fdt boardsetup' command
*
* unless 'fdt_noauto' env var is set we will update the following in the DTB:
* - mtd partitions based on mtdparts/mtdids env
* - system-serial (board serial num from EEPROM)
* - board (full model from EEPROM)
* - peripherals removed from DTB if not loaded on board (per EEPROM config)
*/
void ft_board_setup(void *blob, bd_t *bd)
{
int bit;
struct ventana_board_info *info = &ventana_info;
struct node_info nodes[] = {
{ "sst,w25q256", MTD_DEV_TYPE_NOR, }, /* SPI flash */
{ "fsl,imx6q-gpmi-nand", MTD_DEV_TYPE_NAND, }, /* NAND flash */
};
const char *model = getenv("model");
if (getenv("fdt_noauto")) {
puts(" Skiping ft_board_setup (fdt_noauto defined)\n");
return;
}
/* Update partition nodes using info from mtdparts env var */
puts(" Updating MTD partitions...\n");
fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
if (!model) {
puts("invalid board info: Leaving FDT fully enabled\n");
return;
}
printf(" Adjusting FDT per EEPROM for %s...\n", model);
/* board serial number */
fdt_setprop(blob, 0, "system-serial", getenv("serial#"),
strlen(getenv("serial#") + 1));
/* board (model contains model from device-tree) */
fdt_setprop(blob, 0, "board", info->model,
strlen((const char *)info->model) + 1);
/*
* Peripheral Config:
* remove nodes by alias path if EEPROM config tells us the
* peripheral is not loaded on the board.
*/
for (bit = 0; bit < 64; bit++) {
if (!test_bit(bit, info->config))
fdt_del_node_and_alias(blob, fdt_aliases[bit]);
}
}
#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */