mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-30 00:21:06 +00:00
69c573ca89
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver and add new type for PCA9451A. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Marek Vasut <marex@denx.de>
326 lines
8.6 KiB
C
326 lines
8.6 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* NXP PCA9450 regulator driver
|
|
* Copyright (C) 2022 Marek Vasut <marex@denx.de>
|
|
*
|
|
* Largely based on:
|
|
* ROHM BD71837 regulator driver
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <log.h>
|
|
#include <linux/bitops.h>
|
|
#include <power/pca9450.h>
|
|
#include <power/pmic.h>
|
|
#include <power/regulator.h>
|
|
|
|
#define HW_STATE_CONTROL 0
|
|
#define DEBUG
|
|
|
|
/**
|
|
* struct pca9450_vrange - describe linear range of voltages
|
|
*
|
|
* @min_volt: smallest voltage in range
|
|
* @step: how much voltage changes at each selector step
|
|
* @min_sel: smallest selector in the range
|
|
* @max_sel: maximum selector in the range
|
|
*/
|
|
struct pca9450_vrange {
|
|
unsigned int min_volt;
|
|
unsigned int step;
|
|
u8 min_sel;
|
|
u8 max_sel;
|
|
};
|
|
|
|
/**
|
|
* struct pca9450_plat - describe regulator control registers
|
|
*
|
|
* @name: name of the regulator. Used for matching the dt-entry
|
|
* @enable_reg: register address used to enable/disable regulator
|
|
* @enablemask: register mask used to enable/disable regulator
|
|
* @volt_reg: register address used to configure regulator voltage
|
|
* @volt_mask: register mask used to configure regulator voltage
|
|
* @ranges: pointer to ranges of regulator voltages and matching register
|
|
* values
|
|
* @numranges: number of voltage ranges pointed by ranges
|
|
*/
|
|
struct pca9450_plat {
|
|
const char *name;
|
|
u8 enable_reg;
|
|
u8 enablemask;
|
|
u8 volt_reg;
|
|
u8 volt_mask;
|
|
struct pca9450_vrange *ranges;
|
|
unsigned int numranges;
|
|
};
|
|
|
|
#define PCA_RANGE(_min, _vstep, _sel_low, _sel_hi) \
|
|
{ \
|
|
.min_volt = (_min), .step = (_vstep), \
|
|
.min_sel = (_sel_low), .max_sel = (_sel_hi), \
|
|
}
|
|
|
|
#define PCA_DATA(_name, enreg, enmask, vreg, vmask, _range) \
|
|
{ \
|
|
.name = (_name), .enable_reg = (enreg), .enablemask = (enmask), \
|
|
.volt_reg = (vreg), .volt_mask = (vmask), .ranges = (_range), \
|
|
.numranges = ARRAY_SIZE(_range) \
|
|
}
|
|
|
|
static struct pca9450_vrange pca9450_buck123_vranges[] = {
|
|
PCA_RANGE(600000, 12500, 0, 0x7f),
|
|
};
|
|
|
|
static struct pca9450_vrange pca9450_buck456_vranges[] = {
|
|
PCA_RANGE(600000, 25000, 0, 0x70),
|
|
PCA_RANGE(3400000, 0, 0x71, 0x7f),
|
|
};
|
|
|
|
static struct pca9450_vrange pca9450_ldo1_vranges[] = {
|
|
PCA_RANGE(1600000, 100000, 0x0, 0x3),
|
|
PCA_RANGE(3000000, 100000, 0x4, 0x7),
|
|
};
|
|
|
|
static struct pca9450_vrange pca9450_ldo2_vranges[] = {
|
|
PCA_RANGE(800000, 50000, 0x0, 0x7),
|
|
};
|
|
|
|
static struct pca9450_vrange pca9450_ldo34_vranges[] = {
|
|
PCA_RANGE(800000, 100000, 0x0, 0x19),
|
|
PCA_RANGE(3300000, 0, 0x1a, 0x1f),
|
|
};
|
|
|
|
static struct pca9450_vrange pca9450_ldo5_vranges[] = {
|
|
PCA_RANGE(1800000, 100000, 0x0, 0xf),
|
|
};
|
|
|
|
/*
|
|
* We use enable mask 'HW_STATE_CONTROL' to indicate that this regulator
|
|
* must not be enabled or disabled by SW. The typical use-case for PCA9450
|
|
* is powering NXP i.MX8. In this use-case we (for now) only allow control
|
|
* for BUCK4, BUCK5, BUCK6 which are not boot critical.
|
|
*/
|
|
static struct pca9450_plat pca9450_reg_data[] = {
|
|
/* Bucks 1-3 which support dynamic voltage scaling */
|
|
PCA_DATA("BUCK1", PCA9450_BUCK1CTRL, HW_STATE_CONTROL,
|
|
PCA9450_BUCK1OUT_DVS0, PCA9450_DVS_BUCK_RUN_MASK,
|
|
pca9450_buck123_vranges),
|
|
PCA_DATA("BUCK2", PCA9450_BUCK2CTRL, HW_STATE_CONTROL,
|
|
PCA9450_BUCK2OUT_DVS0, PCA9450_DVS_BUCK_RUN_MASK,
|
|
pca9450_buck123_vranges),
|
|
PCA_DATA("BUCK3", PCA9450_BUCK3CTRL, HW_STATE_CONTROL,
|
|
PCA9450_BUCK3OUT_DVS0, PCA9450_DVS_BUCK_RUN_MASK,
|
|
pca9450_buck123_vranges),
|
|
/* Bucks 4-6 which do not support dynamic voltage scaling */
|
|
PCA_DATA("BUCK4", PCA9450_BUCK4CTRL, HW_STATE_CONTROL,
|
|
PCA9450_BUCK4OUT, PCA9450_DVS_BUCK_RUN_MASK,
|
|
pca9450_buck456_vranges),
|
|
PCA_DATA("BUCK5", PCA9450_BUCK5CTRL, HW_STATE_CONTROL,
|
|
PCA9450_BUCK5OUT, PCA9450_DVS_BUCK_RUN_MASK,
|
|
pca9450_buck456_vranges),
|
|
PCA_DATA("BUCK6", PCA9450_BUCK6CTRL, HW_STATE_CONTROL,
|
|
PCA9450_BUCK6OUT, PCA9450_DVS_BUCK_RUN_MASK,
|
|
pca9450_buck456_vranges),
|
|
/* LDOs */
|
|
PCA_DATA("LDO1", PCA9450_LDO1CTRL, HW_STATE_CONTROL,
|
|
PCA9450_LDO1CTRL, PCA9450_LDO12_MASK,
|
|
pca9450_ldo1_vranges),
|
|
PCA_DATA("LDO2", PCA9450_LDO2CTRL, HW_STATE_CONTROL,
|
|
PCA9450_LDO2CTRL, PCA9450_LDO12_MASK,
|
|
pca9450_ldo2_vranges),
|
|
PCA_DATA("LDO3", PCA9450_LDO3CTRL, HW_STATE_CONTROL,
|
|
PCA9450_LDO3CTRL, PCA9450_LDO34_MASK,
|
|
pca9450_ldo34_vranges),
|
|
PCA_DATA("LDO4", PCA9450_LDO4CTRL, HW_STATE_CONTROL,
|
|
PCA9450_LDO4CTRL, PCA9450_LDO34_MASK,
|
|
pca9450_ldo34_vranges),
|
|
PCA_DATA("LDO5", PCA9450_LDO5CTRL_H, HW_STATE_CONTROL,
|
|
PCA9450_LDO5CTRL_H, PCA9450_LDO5_MASK,
|
|
pca9450_ldo5_vranges),
|
|
};
|
|
|
|
static int vrange_find_value(struct pca9450_vrange *r, unsigned int sel,
|
|
unsigned int *val)
|
|
{
|
|
if (!val || sel < r->min_sel || sel > r->max_sel)
|
|
return -EINVAL;
|
|
|
|
*val = r->min_volt + r->step * (sel - r->min_sel);
|
|
return 0;
|
|
}
|
|
|
|
static int vrange_find_selector(struct pca9450_vrange *r, int val,
|
|
unsigned int *sel)
|
|
{
|
|
int ret = -EINVAL;
|
|
int num_vals = r->max_sel - r->min_sel + 1;
|
|
|
|
if (val >= r->min_volt &&
|
|
val <= r->min_volt + r->step * (num_vals - 1)) {
|
|
if (r->step) {
|
|
*sel = r->min_sel + ((val - r->min_volt) / r->step);
|
|
ret = 0;
|
|
} else {
|
|
*sel = r->min_sel;
|
|
ret = 0;
|
|
}
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static int pca9450_get_enable(struct udevice *dev)
|
|
{
|
|
struct pca9450_plat *plat = dev_get_plat(dev);
|
|
int val;
|
|
|
|
/*
|
|
* boot critical regulators on pca9450 must not be controlled by sw
|
|
* due to the 'feature' which leaves power rails down if pca9450 is
|
|
* reseted to snvs state. hence we can't get the state here.
|
|
*
|
|
* if we are alive it means we probably are on run state and
|
|
* if the regulator can't be controlled we can assume it is
|
|
* enabled.
|
|
*/
|
|
if (plat->enablemask == HW_STATE_CONTROL)
|
|
return 1;
|
|
|
|
val = pmic_reg_read(dev->parent, plat->enable_reg);
|
|
if (val < 0)
|
|
return val;
|
|
|
|
return (val & plat->enablemask);
|
|
}
|
|
|
|
static int pca9450_set_enable(struct udevice *dev, bool enable)
|
|
{
|
|
int val = 0;
|
|
struct pca9450_plat *plat = dev_get_plat(dev);
|
|
|
|
/*
|
|
* boot critical regulators on pca9450 must not be controlled by sw
|
|
* due to the 'feature' which leaves power rails down if pca9450 is
|
|
* reseted to snvs state. Hence we can't set the state here.
|
|
*/
|
|
if (plat->enablemask == HW_STATE_CONTROL)
|
|
return enable ? 0 : -EINVAL;
|
|
|
|
if (enable)
|
|
val = plat->enablemask;
|
|
|
|
return pmic_clrsetbits(dev->parent, plat->enable_reg, plat->enablemask,
|
|
val);
|
|
}
|
|
|
|
static int pca9450_get_value(struct udevice *dev)
|
|
{
|
|
struct pca9450_plat *plat = dev_get_plat(dev);
|
|
unsigned int reg, tmp;
|
|
int i, ret;
|
|
|
|
ret = pmic_reg_read(dev->parent, plat->volt_reg);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
reg = ret;
|
|
reg &= plat->volt_mask;
|
|
|
|
for (i = 0; i < plat->numranges; i++) {
|
|
struct pca9450_vrange *r = &plat->ranges[i];
|
|
|
|
if (!vrange_find_value(r, reg, &tmp))
|
|
return tmp;
|
|
}
|
|
|
|
pr_err("Unknown voltage value read from pmic\n");
|
|
|
|
return -EINVAL;
|
|
}
|
|
|
|
static int pca9450_set_value(struct udevice *dev, int uvolt)
|
|
{
|
|
struct pca9450_plat *plat = dev_get_plat(dev);
|
|
unsigned int sel;
|
|
int i, found = 0;
|
|
|
|
for (i = 0; i < plat->numranges; i++) {
|
|
struct pca9450_vrange *r = &plat->ranges[i];
|
|
|
|
found = !vrange_find_selector(r, uvolt, &sel);
|
|
if (found) {
|
|
unsigned int tmp;
|
|
|
|
/*
|
|
* We require exactly the requested value to be
|
|
* supported - this can be changed later if needed
|
|
*/
|
|
found = !vrange_find_value(r, sel, &tmp);
|
|
if (found && tmp == uvolt)
|
|
break;
|
|
found = 0;
|
|
}
|
|
}
|
|
|
|
if (!found)
|
|
return -EINVAL;
|
|
|
|
return pmic_clrsetbits(dev->parent, plat->volt_reg,
|
|
plat->volt_mask, sel);
|
|
}
|
|
|
|
static int pca9450_regulator_probe(struct udevice *dev)
|
|
{
|
|
struct pca9450_plat *plat = dev_get_plat(dev);
|
|
int i, type;
|
|
|
|
type = dev_get_driver_data(dev_get_parent(dev));
|
|
|
|
if (type != NXP_CHIP_TYPE_PCA9450A && type != NXP_CHIP_TYPE_PCA9450BC &&
|
|
type != NXP_CHIP_TYPE_PCA9451A) {
|
|
debug("Unknown PMIC type\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
for (i = 0; i < ARRAY_SIZE(pca9450_reg_data); i++) {
|
|
if (strcmp(dev->name, pca9450_reg_data[i].name))
|
|
continue;
|
|
|
|
/* PCA9450B/PCA9450C uses BUCK1 and BUCK3 in dual-phase */
|
|
if (type == NXP_CHIP_TYPE_PCA9450BC &&
|
|
!strcmp(pca9450_reg_data[i].name, "BUCK3")) {
|
|
continue;
|
|
}
|
|
|
|
/* PCA9451A uses BUCK3 in dual-phase and don't have LDO2 and LDO3 */
|
|
if (type == NXP_CHIP_TYPE_PCA9451A &&
|
|
(!strcmp(pca9450_reg_data[i].name, "BUCK3") ||
|
|
!strcmp(pca9450_reg_data[i].name, "LDO2") ||
|
|
!strcmp(pca9450_reg_data[i].name, "LDO3"))) {
|
|
continue;
|
|
}
|
|
|
|
*plat = pca9450_reg_data[i];
|
|
|
|
return 0;
|
|
}
|
|
|
|
pr_err("Unknown regulator '%s'\n", dev->name);
|
|
|
|
return -ENOENT;
|
|
}
|
|
|
|
static const struct dm_regulator_ops pca9450_regulator_ops = {
|
|
.get_value = pca9450_get_value,
|
|
.set_value = pca9450_set_value,
|
|
.get_enable = pca9450_get_enable,
|
|
.set_enable = pca9450_set_enable,
|
|
};
|
|
|
|
U_BOOT_DRIVER(pca9450_regulator) = {
|
|
.name = PCA9450_REGULATOR_DRIVER,
|
|
.id = UCLASS_REGULATOR,
|
|
.ops = &pca9450_regulator_ops,
|
|
.probe = pca9450_regulator_probe,
|
|
.plat_auto = sizeof(struct pca9450_plat),
|
|
};
|