u-boot/board/freescale/mpc8572ds/ddr.c
Haiying Wang 4ca06607d6 Add ddr interleaving suppport for MPC8572DS board
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.

* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.

* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-18 21:54:05 +02:00

150 lines
4.3 KiB
C

/*
* Copyright 2008 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <i2c.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
{
i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
}
unsigned int fsl_ddr_get_mem_data_rate(void)
{
return get_ddr_freq(0);
}
void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
unsigned int ctrl_num)
{
unsigned int i;
unsigned int i2c_address = 0;
for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
if (ctrl_num == 0 && i == 0) {
i2c_address = SPD_EEPROM_ADDRESS1;
}
if (ctrl_num == 1 && i == 0) {
i2c_address = SPD_EEPROM_ADDRESS2;
}
get_spd(&(ctrl_dimms_spd[i]), i2c_address);
}
}
typedef struct {
u32 datarate_mhz_low;
u32 datarate_mhz_high;
u32 n_ranks;
u32 clk_adjust;
u32 cpo;
u32 write_data_delay;
u32 force_2T;
} board_specific_parameters_t;
/* ranges for parameters:
* wr_data_delay = 0-6
* clk adjust = 0-8
* cpo 2-0x1E (30)
*/
/* XXX: these values need to be checked for all interleaving modes. */
/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
* seem reliable, but errors will appear when memory intensive
* program is run. */
/* XXX: Single rank at 800 MHz is OK. */
const board_specific_parameters_t board_specific_parameters[][20] = {
{
/* memory controller 0 */
/* lo| hi| num| clk| cpo|wrdata|2T */
/* mhz| mhz|ranks|adjst| | delay| */
{ 0, 333, 2, 6, 7, 3, 0},
{334, 400, 2, 6, 9, 3, 0},
{401, 549, 2, 6, 11, 3, 0},
{550, 680, 2, 1, 10, 5, 0},
{681, 850, 2, 1, 12, 5, 1},
{ 0, 333, 1, 6, 7, 3, 0},
{334, 400, 1, 6, 9, 3, 0},
{401, 549, 1, 6, 11, 3, 0},
{550, 680, 1, 1, 10, 5, 0},
{681, 850, 1, 1, 12, 5, 0}
},
{
/* memory controller 1 */
/* lo| hi| num| clk| cpo|wrdata|2T */
/* mhz| mhz|ranks|adjst| | delay| */
{ 0, 333, 2, 6, 7, 3, 0},
{334, 400, 2, 6, 9, 3, 0},
{401, 549, 2, 6, 11, 3, 0},
{550, 680, 2, 1, 11, 6, 0},
{681, 850, 2, 1, 13, 6, 1},
{ 0, 333, 1, 6, 7, 3, 0},
{334, 400, 1, 6, 9, 3, 0},
{401, 549, 1, 6, 11, 3, 0},
{550, 680, 1, 1, 11, 6, 0},
{681, 850, 1, 1, 13, 6, 0}
}
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
const board_specific_parameters_t *pbsp =
&(board_specific_parameters[ctrl_num][0]);
u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
sizeof(board_specific_parameters[0][0]);
u32 i;
ulong ddr_freq;
/* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
* that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
* there are two dimms in the controller, set odt_rd_cfg to 3 and
* odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
*/
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (i&1) { /* odd CS */
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 0;
} else { /* even CS */
if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 4;
} else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
popts->cs_local_opts[i].odt_rd_cfg = 3;
popts->cs_local_opts[i].odt_wr_cfg = 3;
}
}
}
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
for (i = 0; i < num_params; i++) {
if (ddr_freq >= pbsp->datarate_mhz_low &&
ddr_freq <= pbsp->datarate_mhz_high &&
pdimm->n_ranks == pbsp->n_ranks) {
popts->clk_adjust = pbsp->clk_adjust;
popts->cpo_override = pbsp->cpo;
popts->write_data_delay = pbsp->write_data_delay;
popts->twoT_en = pbsp->force_2T;
}
pbsp++;
}
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
}