mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 15:37:23 +00:00
65aa31d2d0
Fixes this error message when USB is started. "ULPI: ulpi_reset: failed writing reset bit" It is pointless to manually reset the ULPI as the USB Host Reset and PHY RESET line should take care of that. Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Roger Quadros <rogerq@ti.com>
445 lines
13 KiB
C
445 lines
13 KiB
C
/*
|
|
* (C) Copyright 2006-2008
|
|
* Texas Instruments.
|
|
* Richard Woodruff <r-woodruff2@ti.com>
|
|
* Syed Mohammed Khasim <x0khasim@ti.com>
|
|
*
|
|
* Configuration settings for the TI OMAP3530 Beagle board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_OMAP 1 /* in a TI OMAP core */
|
|
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
|
|
#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
|
|
#define CONFIG_OMAP_GPIO
|
|
#define CONFIG_OMAP_COMMON
|
|
|
|
#define CONFIG_SDRC /* The chip has SDRC controller */
|
|
|
|
#include <asm/arch/cpu.h> /* get chip and board defs */
|
|
#include <asm/arch/omap3.h>
|
|
|
|
/*
|
|
* Display CPU and Board information
|
|
*/
|
|
#define CONFIG_DISPLAY_CPUINFO 1
|
|
#define CONFIG_DISPLAY_BOARDINFO 1
|
|
|
|
/* Clock Defines */
|
|
#define V_OSCK 26000000 /* Clock output from T2 */
|
|
#define V_SCLK (V_OSCK >> 1)
|
|
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
#define CONFIG_OF_LIBFDT
|
|
#define CONFIG_CMD_BOOTZ
|
|
|
|
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS 1
|
|
#define CONFIG_INITRD_TAG 1
|
|
#define CONFIG_REVISION_TAG 1
|
|
|
|
/*
|
|
* Size of malloc() pool
|
|
*/
|
|
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
|
|
/* Sector */
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
|
|
|
|
/*
|
|
* Hardware drivers
|
|
*/
|
|
|
|
/*
|
|
* NS16550 Configuration
|
|
*/
|
|
#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
|
|
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
|
|
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*/
|
|
#define CONFIG_CONS_INDEX 3
|
|
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
|
|
#define CONFIG_SERIAL3 3 /* UART3 on Beagle Rev 2 */
|
|
|
|
/* allow to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
#define CONFIG_BAUDRATE 115200
|
|
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
|
|
115200}
|
|
#define CONFIG_GENERIC_MMC 1
|
|
#define CONFIG_MMC 1
|
|
#define CONFIG_OMAP_HSMMC 1
|
|
#define CONFIG_DOS_PARTITION 1
|
|
|
|
/* Status LED */
|
|
#define CONFIG_STATUS_LED 1
|
|
#define CONFIG_BOARD_SPECIFIC_LED 1
|
|
#define STATUS_LED_BIT 0x01
|
|
#define STATUS_LED_STATE STATUS_LED_ON
|
|
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
|
|
#define STATUS_LED_BIT1 0x02
|
|
#define STATUS_LED_STATE1 STATUS_LED_ON
|
|
#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
|
|
#define STATUS_LED_BOOT STATUS_LED_BIT
|
|
#define STATUS_LED_GREEN STATUS_LED_BIT1
|
|
|
|
/* Enable Multi Bus support for I2C */
|
|
#define CONFIG_I2C_MULTI_BUS 1
|
|
|
|
/* Probe all devices */
|
|
#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}
|
|
|
|
/* USB */
|
|
#define CONFIG_MUSB_GADGET
|
|
#define CONFIG_USB_MUSB_OMAP2PLUS
|
|
#define CONFIG_MUSB_PIO_ONLY
|
|
#define CONFIG_USB_GADGET_DUALSPEED
|
|
#define CONFIG_TWL4030_USB 1
|
|
#define CONFIG_USB_ETHER
|
|
#define CONFIG_USB_ETHER_RNDIS
|
|
|
|
/* USB EHCI */
|
|
#define CONFIG_CMD_USB
|
|
#define CONFIG_USB_EHCI
|
|
|
|
#define CONFIG_USB_EHCI_OMAP
|
|
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
|
|
|
|
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
|
|
#define CONFIG_USB_HOST_ETHER
|
|
#define CONFIG_USB_ETHER_SMSC95XX
|
|
#define CONFIG_USB_ETHER_ASIX
|
|
|
|
|
|
/* commands to include */
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
|
|
#define CONFIG_CMD_CACHE
|
|
#define CONFIG_CMD_EXT2 /* EXT2 Support */
|
|
#define CONFIG_CMD_FAT /* FAT support */
|
|
#define CONFIG_CMD_FS_GENERIC /* Generic FS support */
|
|
#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
|
|
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
|
|
#define MTDIDS_DEFAULT "nand0=nand"
|
|
#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
|
|
"1920k(u-boot),128k(u-boot-env),"\
|
|
"4m(kernel),-(fs)"
|
|
|
|
#define CONFIG_CMD_I2C /* I2C serial bus support */
|
|
#define CONFIG_CMD_MMC /* MMC support */
|
|
#define CONFIG_USB_STORAGE /* USB storage support */
|
|
#define CONFIG_CMD_NAND /* NAND support */
|
|
#define CONFIG_CMD_LED /* LED support */
|
|
#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
|
|
#define CONFIG_CMD_NFS /* NFS support */
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_SETEXPR /* Evaluate expressions */
|
|
#define CONFIG_CMD_GPIO /* Enable gpio command */
|
|
|
|
#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
|
|
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
|
|
#undef CONFIG_CMD_IMI /* iminfo */
|
|
#undef CONFIG_CMD_IMLS /* List all found images */
|
|
|
|
#define CONFIG_SYS_NO_FLASH
|
|
#define CONFIG_HARD_I2C 1
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
#define CONFIG_SYS_I2C_SLAVE 1
|
|
#define CONFIG_I2C_MULTI_BUS 1
|
|
#define CONFIG_DRIVER_OMAP34XX_I2C 1
|
|
#define CONFIG_VIDEO_OMAP3 /* DSS Support */
|
|
|
|
/*
|
|
* TWL4030
|
|
*/
|
|
#define CONFIG_TWL4030_POWER 1
|
|
#define CONFIG_TWL4030_LED 1
|
|
|
|
/*
|
|
* Board NAND Info.
|
|
*/
|
|
#define CONFIG_SYS_NAND_QUIET_TEST 1
|
|
#define CONFIG_NAND_OMAP_GPMC
|
|
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
|
|
/* to access nand */
|
|
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
|
|
/* to access nand at */
|
|
/* CS0 */
|
|
#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
|
|
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
|
|
/* devices */
|
|
|
|
/* Environment information */
|
|
#define CONFIG_BOOTDELAY 3
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"loadaddr=0x80200000\0" \
|
|
"rdaddr=0x81000000\0" \
|
|
"fdt_high=0xffffffff\0" \
|
|
"fdtaddr=0x80f80000\0" \
|
|
"usbtty=cdc_acm\0" \
|
|
"bootfile=uImage\0" \
|
|
"ramdisk=ramdisk.gz\0" \
|
|
"bootdir=/boot\0" \
|
|
"bootpart=0:2\0" \
|
|
"console=ttyO2,115200n8\0" \
|
|
"mpurate=auto\0" \
|
|
"buddy=none\0" \
|
|
"optargs=\0" \
|
|
"camera=none\0" \
|
|
"vram=12M\0" \
|
|
"dvimode=640x480MR-16@60\0" \
|
|
"defaultdisplay=dvi\0" \
|
|
"mmcdev=0\0" \
|
|
"mmcroot=/dev/mmcblk0p2 rw\0" \
|
|
"mmcrootfstype=ext3 rootwait\0" \
|
|
"nandroot=ubi0:rootfs ubi.mtd=4\0" \
|
|
"nandrootfstype=ubifs\0" \
|
|
"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
|
|
"ramrootfstype=ext2\0" \
|
|
"mmcargs=setenv bootargs console=${console} " \
|
|
"${optargs} " \
|
|
"mpurate=${mpurate} " \
|
|
"buddy=${buddy} "\
|
|
"camera=${camera} "\
|
|
"vram=${vram} " \
|
|
"omapfb.mode=dvi:${dvimode} " \
|
|
"omapdss.def_disp=${defaultdisplay} " \
|
|
"root=${mmcroot} " \
|
|
"rootfstype=${mmcrootfstype}\0" \
|
|
"nandargs=setenv bootargs console=${console} " \
|
|
"${optargs} " \
|
|
"mpurate=${mpurate} " \
|
|
"buddy=${buddy} "\
|
|
"camera=${camera} "\
|
|
"vram=${vram} " \
|
|
"omapfb.mode=dvi:${dvimode} " \
|
|
"omapdss.def_disp=${defaultdisplay} " \
|
|
"root=${nandroot} " \
|
|
"rootfstype=${nandrootfstype}\0" \
|
|
"findfdt=" \
|
|
"if test $beaglerev = AxBx; then " \
|
|
"setenv fdtfile omap3-beagle.dtb; fi; " \
|
|
"if test $beaglerev = Cx; then " \
|
|
"setenv fdtfile omap3-beagle.dtb; fi; " \
|
|
"if test $beaglerev = xMAB; then " \
|
|
"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
|
|
"if test $beaglerev = xMC; then " \
|
|
"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
|
|
"if test $fdtfile = undefined; then " \
|
|
"echo WARNING: Could not determine device tree to use; fi; \0" \
|
|
"bootenv=uEnv.txt\0" \
|
|
"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
|
|
"importbootenv=echo Importing environment from mmc ...; " \
|
|
"env import -t $loadaddr $filesize\0" \
|
|
"ramargs=setenv bootargs console=${console} " \
|
|
"${optargs} " \
|
|
"mpurate=${mpurate} " \
|
|
"buddy=${buddy} "\
|
|
"vram=${vram} " \
|
|
"omapfb.mode=dvi:${dvimode} " \
|
|
"omapdss.def_disp=${defaultdisplay} " \
|
|
"root=${ramroot} " \
|
|
"rootfstype=${ramrootfstype}\0" \
|
|
"loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
|
|
"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
|
|
"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
|
|
"mmcboot=echo Booting from mmc ...; " \
|
|
"run mmcargs; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
|
|
"run mmcargs; " \
|
|
"bootz ${loadaddr} - ${fdtaddr}\0" \
|
|
"nandboot=echo Booting from nand ...; " \
|
|
"run nandargs; " \
|
|
"nand read ${loadaddr} 280000 400000; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"ramboot=echo Booting from ramdisk ...; " \
|
|
"run ramargs; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"userbutton=if gpio input 173; then run userbutton_xm; " \
|
|
"else run userbutton_nonxm; fi;\0" \
|
|
"userbutton_xm=gpio input 4;\0" \
|
|
"userbutton_nonxm=gpio input 7;\0"
|
|
/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"run findfdt; " \
|
|
"mmc dev ${mmcdev}; if mmc rescan; then " \
|
|
"if run userbutton; then " \
|
|
"setenv bootenv uEnv.txt;" \
|
|
"else " \
|
|
"setenv bootenv user.txt;" \
|
|
"fi;" \
|
|
"echo SD/MMC found on device ${mmcdev};" \
|
|
"if run loadbootenv; then " \
|
|
"echo Loaded environment from ${bootenv};" \
|
|
"run importbootenv;" \
|
|
"fi;" \
|
|
"if test -n $uenvcmd; then " \
|
|
"echo Running uenvcmd ...;" \
|
|
"run uenvcmd;" \
|
|
"fi;" \
|
|
"if run loadimage; then " \
|
|
"run mmcboot;" \
|
|
"fi;" \
|
|
"fi;" \
|
|
"run nandboot;" \
|
|
"setenv bootfile zImage;" \
|
|
"if run loadimage; then " \
|
|
"run loadfdt;" \
|
|
"run mmcbootz; " \
|
|
"fi; " \
|
|
|
|
#define CONFIG_AUTO_COMPLETE 1
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
|
|
#define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # "
|
|
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
|
|
sizeof(CONFIG_SYS_PROMPT) + 16)
|
|
#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
|
|
/* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
|
|
|
|
#define CONFIG_SYS_ALT_MEMTEST 1
|
|
#define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */
|
|
/* defaults */
|
|
#define CONFIG_SYS_MEMTEST_END (0x87FFFFFF) /* 128MB */
|
|
#define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
|
|
/* load address */
|
|
|
|
/*
|
|
* OMAP3 has 12 GP timers, they can be driven by the system clock
|
|
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
|
|
* This rate is divided by a local divisor.
|
|
*/
|
|
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
|
|
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Physical Memory Map
|
|
*/
|
|
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
|
|
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
|
|
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH and environment organization
|
|
*/
|
|
|
|
/* **** PISMO SUPPORT *** */
|
|
|
|
/* Configure the PISMO */
|
|
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
|
|
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
|
|
|
|
#if defined(CONFIG_CMD_NAND)
|
|
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
|
|
#endif
|
|
|
|
/* Monitor at start of flash */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
|
|
|
|
#define CONFIG_ENV_IS_IN_NAND 1
|
|
#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
|
|
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
|
|
|
|
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
|
|
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
|
|
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
|
|
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
|
|
#define CONFIG_OMAP3_SPI
|
|
|
|
#define CONFIG_SYS_CACHELINE_SIZE 64
|
|
|
|
/* Defines for SPL */
|
|
#define CONFIG_SPL
|
|
#define CONFIG_SPL_FRAMEWORK
|
|
#define CONFIG_SPL_NAND_SIMPLE
|
|
#define CONFIG_SPL_TEXT_BASE 0x40200800
|
|
#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
|
|
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
|
|
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
|
|
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
|
|
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
|
|
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
|
|
#define CONFIG_SPL_BOARD_INIT
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
|
#define CONFIG_SPL_LIBDISK_SUPPORT
|
|
#define CONFIG_SPL_I2C_SUPPORT
|
|
#define CONFIG_SPL_LIBGENERIC_SUPPORT
|
|
#define CONFIG_SPL_MMC_SUPPORT
|
|
#define CONFIG_SPL_FAT_SUPPORT
|
|
#define CONFIG_SPL_SERIAL_SUPPORT
|
|
#define CONFIG_SPL_NAND_SUPPORT
|
|
#define CONFIG_SPL_NAND_BASE
|
|
#define CONFIG_SPL_NAND_DRIVERS
|
|
#define CONFIG_SPL_NAND_ECC
|
|
#define CONFIG_SPL_GPIO_SUPPORT
|
|
#define CONFIG_SPL_POWER_SUPPORT
|
|
#define CONFIG_SPL_OMAP3_ID_NAND
|
|
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
|
|
|
|
/* NAND boot config */
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_PAGE_COUNT 64
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
|
|
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
|
|
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
|
|
10, 11, 12, 13}
|
|
#define CONFIG_SYS_NAND_ECCSIZE 512
|
|
#define CONFIG_SYS_NAND_ECCBYTES 3
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
|
|
|
|
/*
|
|
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
|
|
* 64 bytes before this address should be set aside for u-boot.img's
|
|
* header. That is 0x800FFFC0--0x80100000 should not be used for any
|
|
* other needs.
|
|
*/
|
|
#define CONFIG_SYS_TEXT_BASE 0x80100000
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
|
|
|
|
#endif /* __CONFIG_H */
|