mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-24 21:54:01 +00:00
86ac7a9a5d
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to DRAM. The boot log with Arm trusted firmware console enabled: " U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) PMIC: PFUZE100 ID=0x10 Normal Boot Trying to boot from MMC2 NOTICE: Configureing TZASC380 NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty NOTICE: BL31: Built : 09:28:54, Nov 8 2018 lpddr4 swffc start NOTICE: sip svc init U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz Reset cause: POR Model: Freescale i.MX8MQ EVK DRAM: 3 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: Warning: ethernet@30be0000 using MAC address from ROM eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 " Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
246 lines
6 KiB
C
246 lines
6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2018 NXP
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <errno.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/ddr.h>
|
|
#include <asm/arch/imx8mq_pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/mach-imx/gpio.h>
|
|
#include <asm/mach-imx/mxc_i2c.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <mmc.h>
|
|
#include <power/pmic.h>
|
|
#include <power/pfuze100_pmic.h>
|
|
#include <spl.h>
|
|
#include "../common/pfuze.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
extern struct dram_timing_info dram_timing_b0;
|
|
|
|
void spl_dram_init(void)
|
|
{
|
|
/* ddr init */
|
|
if ((get_cpu_rev() & 0xfff) == CHIP_REV_2_1)
|
|
ddr_init(&dram_timing);
|
|
else
|
|
ddr_init(&dram_timing_b0);
|
|
}
|
|
|
|
#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
|
|
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
|
|
struct i2c_pads_info i2c_pad_info1 = {
|
|
.scl = {
|
|
.i2c_mode = IMX8MQ_PAD_I2C1_SCL__I2C1_SCL | PC,
|
|
.gpio_mode = IMX8MQ_PAD_I2C1_SCL__GPIO5_IO14 | PC,
|
|
.gp = IMX_GPIO_NR(5, 14),
|
|
},
|
|
.sda = {
|
|
.i2c_mode = IMX8MQ_PAD_I2C1_SDA__I2C1_SDA | PC,
|
|
.gpio_mode = IMX8MQ_PAD_I2C1_SDA__GPIO5_IO15 | PC,
|
|
.gp = IMX_GPIO_NR(5, 15),
|
|
},
|
|
};
|
|
|
|
#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 12)
|
|
#define USDHC1_PWR_GPIO IMX_GPIO_NR(2, 10)
|
|
#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
|
|
|
|
int board_mmc_getcd(struct mmc *mmc)
|
|
{
|
|
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
|
|
int ret = 0;
|
|
|
|
switch (cfg->esdhc_base) {
|
|
case USDHC1_BASE_ADDR:
|
|
ret = 1;
|
|
break;
|
|
case USDHC2_BASE_ADDR:
|
|
ret = !gpio_get_value(USDHC2_CD_GPIO);
|
|
return ret;
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
|
|
#define USDHC_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | \
|
|
PAD_CTL_FSEL2)
|
|
#define USDHC_GPIO_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_DSE1)
|
|
|
|
static iomux_v3_cfg_t const usdhc1_pads[] = {
|
|
IMX8MQ_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA4__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA5__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA6__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_DATA7__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
IMX8MQ_PAD_SD1_RESET_B__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const usdhc2_pads[] = {
|
|
IMX8MQ_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
|
|
IMX8MQ_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
|
|
IMX8MQ_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
|
|
IMX8MQ_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
|
|
IMX8MQ_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0x16 */
|
|
IMX8MQ_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), /* 0xd6 */
|
|
IMX8MQ_PAD_SD2_CD_B__GPIO2_IO12 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
|
|
IMX8MQ_PAD_SD2_RESET_B__GPIO2_IO19 | MUX_PAD_CTRL(USDHC_GPIO_PAD_CTRL),
|
|
};
|
|
|
|
static struct fsl_esdhc_cfg usdhc_cfg[2] = {
|
|
{USDHC1_BASE_ADDR, 0, 8},
|
|
{USDHC2_BASE_ADDR, 0, 4},
|
|
};
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
int i, ret;
|
|
/*
|
|
* According to the board_mmc_init() the following map is done:
|
|
* (U-Boot device node) (Physical Port)
|
|
* mmc0 USDHC1
|
|
* mmc1 USDHC2
|
|
*/
|
|
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
|
|
switch (i) {
|
|
case 0:
|
|
init_clk_usdhc(0);
|
|
usdhc_cfg[0].sdhc_clk = mxc_get_clock(USDHC1_CLK_ROOT);
|
|
imx_iomux_v3_setup_multiple_pads(usdhc1_pads,
|
|
ARRAY_SIZE(usdhc1_pads));
|
|
gpio_request(USDHC1_PWR_GPIO, "usdhc1_reset");
|
|
gpio_direction_output(USDHC1_PWR_GPIO, 0);
|
|
udelay(500);
|
|
gpio_direction_output(USDHC1_PWR_GPIO, 1);
|
|
break;
|
|
case 1:
|
|
init_clk_usdhc(1);
|
|
usdhc_cfg[1].sdhc_clk = mxc_get_clock(USDHC2_CLK_ROOT);
|
|
imx_iomux_v3_setup_multiple_pads(usdhc2_pads,
|
|
ARRAY_SIZE(usdhc2_pads));
|
|
gpio_request(USDHC2_PWR_GPIO, "usdhc2_reset");
|
|
gpio_direction_output(USDHC2_PWR_GPIO, 0);
|
|
udelay(500);
|
|
gpio_direction_output(USDHC2_PWR_GPIO, 1);
|
|
break;
|
|
default:
|
|
printf("Warning: you configured more USDHC controllers(%d) than supported by the board\n", i + 1);
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_POWER
|
|
#define I2C_PMIC 0
|
|
int power_init_board(void)
|
|
{
|
|
struct pmic *p;
|
|
int ret;
|
|
unsigned int reg;
|
|
|
|
ret = power_pfuze100_init(I2C_PMIC);
|
|
if (ret)
|
|
return -ENODEV;
|
|
|
|
p = pmic_get("PFUZE100");
|
|
ret = pmic_probe(p);
|
|
if (ret)
|
|
return -ENODEV;
|
|
|
|
pmic_reg_read(p, PFUZE100_DEVICEID, ®);
|
|
printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
|
|
|
|
pmic_reg_read(p, PFUZE100_SW3AVOL, ®);
|
|
if ((reg & 0x3f) != 0x18) {
|
|
reg &= ~0x3f;
|
|
reg |= 0x18;
|
|
pmic_reg_write(p, PFUZE100_SW3AVOL, reg);
|
|
}
|
|
|
|
ret = pfuze_mode_init(p, APS_PFM);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* set SW3A standby mode to off */
|
|
pmic_reg_read(p, PFUZE100_SW3AMODE, ®);
|
|
reg &= ~0xf;
|
|
reg |= APS_OFF;
|
|
pmic_reg_write(p, PFUZE100_SW3AMODE, reg);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
void spl_board_init(void)
|
|
{
|
|
puts("Normal Boot\n");
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_LOAD_FIT
|
|
int board_fit_config_name_match(const char *name)
|
|
{
|
|
/* Just empty function now - can't decide what to choose */
|
|
debug("%s: %s\n", __func__, name);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
int ret;
|
|
|
|
/* Clear global data */
|
|
memset((void *)gd, 0, sizeof(gd_t));
|
|
|
|
arch_cpu_init();
|
|
|
|
init_uart_clk(0);
|
|
|
|
board_early_init_f();
|
|
|
|
timer_init();
|
|
|
|
preloader_console_init();
|
|
|
|
/* Clear the BSS. */
|
|
memset(__bss_start, 0, __bss_end - __bss_start);
|
|
|
|
ret = spl_init();
|
|
if (ret) {
|
|
debug("spl_init() failed: %d\n", ret);
|
|
hang();
|
|
}
|
|
|
|
enable_tzc380();
|
|
|
|
/* Adjust pmic voltage to 1.0V for 800M */
|
|
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
|
|
|
|
power_init_board();
|
|
|
|
/* DDR initialization */
|
|
spl_dram_init();
|
|
|
|
board_init_r(NULL, 0);
|
|
}
|