mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-07 21:54:45 +00:00
711f2dc08d
This enables the use of the MSCC serial GPIO driver to control the LEDs on the MSCC VCoreIII 'luton' SoC. Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
72 lines
1.4 KiB
C
72 lines
1.4 KiB
C
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Copyright (c) 2018 Microsemi Corporation
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <led.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
enum {
|
|
BOARD_TYPE_PCB090 = 0xAABBCD00,
|
|
BOARD_TYPE_PCB091,
|
|
};
|
|
|
|
void board_debug_uart_init(void)
|
|
{
|
|
/* too early for the pinctrl driver, so configure the UART pins here */
|
|
mscc_gpio_set_alternate(30, 1);
|
|
mscc_gpio_set_alternate(31, 1);
|
|
}
|
|
|
|
int board_early_init_r(void)
|
|
{
|
|
/* Prepare SPI controller to be used in master mode */
|
|
writel(0, BASE_CFG + ICPU_SW_MODE);
|
|
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE;
|
|
|
|
/* LED setup */
|
|
if (IS_ENABLED(CONFIG_LED))
|
|
led_default_state();
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void do_board_detect(void)
|
|
{
|
|
u32 chipid = (readl(BASE_DEVCPU_GCB + CHIP_ID) >> 12) & 0xFFFF;
|
|
|
|
if (chipid == 0x7428 || chipid == 0x7424)
|
|
gd->board_type = BOARD_TYPE_PCB091; // Lu10
|
|
else
|
|
gd->board_type = BOARD_TYPE_PCB090; // Lu26
|
|
}
|
|
|
|
#if defined(CONFIG_MULTI_DTB_FIT)
|
|
int board_fit_config_name_match(const char *name)
|
|
{
|
|
if (gd->board_type == BOARD_TYPE_PCB090 &&
|
|
strcmp(name, "luton_pcb090") == 0)
|
|
return 0;
|
|
|
|
if (gd->board_type == BOARD_TYPE_PCB091 &&
|
|
strcmp(name, "luton_pcb091") == 0)
|
|
return 0;
|
|
|
|
return -1;
|
|
}
|
|
#endif
|
|
|
|
#if defined(CONFIG_DTB_RESELECT)
|
|
int embedded_dtb_select(void)
|
|
{
|
|
do_board_detect();
|
|
fdtdec_setup();
|
|
|
|
return 0;
|
|
}
|
|
#endif
|