u-boot/board/freescale/m5271evb/m5271evb.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

115 lines
2.8 KiB
C

/*
* (C) Copyright 2000-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/immap.h>
int checkboard (void) {
puts ("Board: Freescale M5271EVB\n");
return 0;
};
phys_size_t initdram (int board_type) {
int i;
/* Enable Address lines 23-21 and lower 16bits of data path */
mbar_writeByte(MCF_GPIO_PAR_AD, MCF_GPIO_AD_ADDR23 |
MCF_GPIO_AD_ADDR22 | MCF_GPIO_AD_ADDR21 |
MCF_GPIO_AD_DATAL);
/* Set CS2 pin to be SD_CS0 */
mbar_writeByte(MCF_GPIO_PAR_CS, mbar_readByte(MCF_GPIO_PAR_CS)
| MCF_GPIO_PAR_CS_PAR_CS2);
/* Configure SDRAM Control Pin Assignemnt Register */
mbar_writeByte(MCF_GPIO_PAR_SDRAM, MCF_GPIO_SDRAM_CSSDCS_00 |
MCF_GPIO_SDRAM_SDWE | MCF_GPIO_SDRAM_SCAS |
MCF_GPIO_SDRAM_SRAS | MCF_GPIO_SDRAM_SCKE |
MCF_GPIO_SDRAM_SDCS_11);
asm(" nop");
/*
* Check to see if the SDRAM has already been initialized
* by a run control tool
*/
if (!(mbar_readLong(MCF_SDRAMC_DACR0) & MCF_SDRAMC_DACRn_RE)) {
/* Initialize DRAM Control Register: DCR */
mbar_writeShort(MCF_SDRAMC_DCR,
MCF_SDRAMC_DCR_RTIM(2)
| MCF_SDRAMC_DCR_RC(0x2E));
asm(" nop");
/*
* Initialize DACR0
*
* CASL: 01
* CBM: cmd at A20, bank select bits 21 and up
* PS: 32bit port size
*/
mbar_writeLong(MCF_SDRAMC_DACR0,
MCF_SDRAMC_DACRn_BA(CONFIG_SYS_SDRAM_BASE>>18)
| MCF_SDRAMC_DACRn_CASL(1)
| MCF_SDRAMC_DACRn_CBM(3)
| MCF_SDRAMC_DACRn_PS(0));
asm(" nop");
/* Initialize DMR0 */
mbar_writeLong(MCF_SDRAMC_DMR0,
MCF_SDRAMC_DMRn_BAM_16M
| MCF_SDRAMC_DMRn_V);
asm(" nop");
/* Set IP bit in DACR */
mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
| MCF_SDRAMC_DACRn_IP);
asm(" nop");
/* Wait at least 20ns to allow banks to precharge */
for (i = 0; i < 5; i++)
asm(" nop");
/* Write to this block to initiate precharge */
*(u32 *)(CONFIG_SYS_SDRAM_BASE) = 0xa5a5a5a5;
asm(" nop");
/* Set RE bit in DACR */
mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
| MCF_SDRAMC_DACRn_RE);
/* Wait for at least 8 auto refresh cycles to occur */
for (i = 0; i < 2000; i++)
asm(" nop");
/* Finish the configuration by issuing the MRS */
mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
| MCF_SDRAMC_DACRn_MRS);
asm(" nop");
/*
* Write to the SDRAM Mode Register A0-A11 = 0x400
*
* Write Burst Mode = Programmed Burst Length
* Op Mode = Standard Op
* CAS Latency = 2
* Burst Type = Sequential
* Burst Length = 1
*/
*(u32 *)(CONFIG_SYS_SDRAM_BASE + 0x400) = 0xa5a5a5a5;
asm(" nop");
}
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
};
int testdram (void) {
/* TODO: XXX XXX XXX */
printf ("DRAM test not implemented!\n");
return (0);
}