mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-24 12:03:39 +00:00
04355de71d
When used with a device tree, this will extract the card detect and write protect pins from the device tree and configure them accordingly. This assumes the GPIO_ACTIVE_LOW/HIGH is supported by da8xx_gpio. Signed-off-by: Adam Ford <aford173@gmail.com>
568 lines
14 KiB
C
568 lines
14 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Davinci MMC Controller Driver
|
|
*
|
|
* Copyright (C) 2010 Texas Instruments Incorporated
|
|
*/
|
|
|
|
#include <config.h>
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <errno.h>
|
|
#include <mmc.h>
|
|
#include <command.h>
|
|
#include <part.h>
|
|
#include <malloc.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/sdmmc_defs.h>
|
|
#include <asm-generic/gpio.h>
|
|
|
|
#define DAVINCI_MAX_BLOCKS (32)
|
|
#define WATCHDOG_COUNT (100000)
|
|
|
|
#define get_val(addr) REG(addr)
|
|
#define set_val(addr, val) REG(addr) = (val)
|
|
#define set_bit(addr, val) set_val((addr), (get_val(addr) | (val)))
|
|
#define clear_bit(addr, val) set_val((addr), (get_val(addr) & ~(val)))
|
|
|
|
#ifdef CONFIG_DM_MMC
|
|
struct davinci_of_data {
|
|
const char *name;
|
|
u8 version;
|
|
};
|
|
|
|
/* Davinci MMC board definitions */
|
|
struct davinci_mmc_priv {
|
|
struct davinci_mmc_regs *reg_base; /* Register base address */
|
|
uint input_clk; /* Input clock to MMC controller */
|
|
uint version; /* MMC Controller version */
|
|
struct gpio_desc cd_gpio; /* Card Detect GPIO */
|
|
struct gpio_desc wp_gpio; /* Write Protect GPIO */
|
|
};
|
|
|
|
struct davinci_mmc_plat
|
|
{
|
|
struct mmc_config cfg;
|
|
struct mmc mmc;
|
|
};
|
|
#endif
|
|
|
|
/* Set davinci clock prescalar value based on the required clock in HZ */
|
|
#if !CONFIG_IS_ENABLED(DM_MMC)
|
|
static void dmmc_set_clock(struct mmc *mmc, uint clock)
|
|
{
|
|
struct davinci_mmc *host = mmc->priv;
|
|
#else
|
|
|
|
static void davinci_mmc_set_clock(struct udevice *dev, uint clock)
|
|
{
|
|
struct davinci_mmc_priv *host = dev_get_priv(dev);
|
|
struct mmc *mmc = mmc_get_mmc_dev(dev);
|
|
#endif
|
|
struct davinci_mmc_regs *regs = host->reg_base;
|
|
uint clkrt, sysclk2, act_clock;
|
|
|
|
if (clock < mmc->cfg->f_min)
|
|
clock = mmc->cfg->f_min;
|
|
if (clock > mmc->cfg->f_max)
|
|
clock = mmc->cfg->f_max;
|
|
|
|
set_val(®s->mmcclk, 0);
|
|
sysclk2 = host->input_clk;
|
|
clkrt = (sysclk2 / (2 * clock)) - 1;
|
|
|
|
/* Calculate the actual clock for the divider used */
|
|
act_clock = (sysclk2 / (2 * (clkrt + 1)));
|
|
|
|
/* Adjust divider if actual clock exceeds the required clock */
|
|
if (act_clock > clock)
|
|
clkrt++;
|
|
|
|
/* check clock divider boundary and correct it */
|
|
if (clkrt > 0xFF)
|
|
clkrt = 0xFF;
|
|
|
|
set_val(®s->mmcclk, (clkrt | MMCCLK_CLKEN));
|
|
}
|
|
|
|
/* Status bit wait loop for MMCST1 */
|
|
static int
|
|
dmmc_wait_fifo_status(volatile struct davinci_mmc_regs *regs, uint status)
|
|
{
|
|
uint wdog = WATCHDOG_COUNT;
|
|
|
|
while (--wdog && ((get_val(®s->mmcst1) & status) != status))
|
|
udelay(10);
|
|
|
|
if (!(get_val(®s->mmcctl) & MMCCTL_WIDTH_4_BIT))
|
|
udelay(100);
|
|
|
|
if (wdog == 0)
|
|
return -ECOMM;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Busy bit wait loop for MMCST1 */
|
|
static int dmmc_busy_wait(volatile struct davinci_mmc_regs *regs)
|
|
{
|
|
uint wdog = WATCHDOG_COUNT;
|
|
|
|
while (--wdog && (get_val(®s->mmcst1) & MMCST1_BUSY))
|
|
udelay(10);
|
|
|
|
if (wdog == 0)
|
|
return -ECOMM;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Status bit wait loop for MMCST0 - Checks for error bits as well */
|
|
static int dmmc_check_status(volatile struct davinci_mmc_regs *regs,
|
|
uint *cur_st, uint st_ready, uint st_error)
|
|
{
|
|
uint wdog = WATCHDOG_COUNT;
|
|
uint mmcstatus = *cur_st;
|
|
|
|
while (wdog--) {
|
|
if (mmcstatus & st_ready) {
|
|
*cur_st = mmcstatus;
|
|
mmcstatus = get_val(®s->mmcst1);
|
|
return 0;
|
|
} else if (mmcstatus & st_error) {
|
|
if (mmcstatus & MMCST0_TOUTRS)
|
|
return -ETIMEDOUT;
|
|
printf("[ ST0 ERROR %x]\n", mmcstatus);
|
|
/*
|
|
* Ignore CRC errors as some MMC cards fail to
|
|
* initialize on DM365-EVM on the SD1 slot
|
|
*/
|
|
if (mmcstatus & MMCST0_CRCRS)
|
|
return 0;
|
|
return -ECOMM;
|
|
}
|
|
udelay(10);
|
|
|
|
mmcstatus = get_val(®s->mmcst0);
|
|
}
|
|
|
|
printf("Status %x Timeout ST0:%x ST1:%x\n", st_ready, mmcstatus,
|
|
get_val(®s->mmcst1));
|
|
return -ECOMM;
|
|
}
|
|
|
|
/*
|
|
* Sends a command out on the bus. Takes the device pointer,
|
|
* a command pointer, and an optional data pointer.
|
|
*/
|
|
#if !CONFIG_IS_ENABLED(DM_MMC)
|
|
static int dmmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
|
|
{
|
|
struct davinci_mmc *host = mmc->priv;
|
|
#else
|
|
static int
|
|
davinci_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, struct mmc_data *data)
|
|
{
|
|
struct davinci_mmc_priv *host = dev_get_priv(dev);
|
|
#endif
|
|
volatile struct davinci_mmc_regs *regs = host->reg_base;
|
|
uint mmcstatus, status_rdy, status_err;
|
|
uint i, cmddata, bytes_left = 0;
|
|
int fifo_words, fifo_bytes, err;
|
|
char *data_buf = NULL;
|
|
|
|
/* Clear status registers */
|
|
mmcstatus = get_val(®s->mmcst0);
|
|
fifo_words = (host->version == MMC_CTLR_VERSION_2) ? 16 : 8;
|
|
fifo_bytes = fifo_words << 2;
|
|
|
|
/* Wait for any previous busy signal to be cleared */
|
|
dmmc_busy_wait(regs);
|
|
|
|
cmddata = cmd->cmdidx;
|
|
cmddata |= MMCCMD_PPLEN;
|
|
|
|
/* Send init clock for CMD0 */
|
|
if (cmd->cmdidx == MMC_CMD_GO_IDLE_STATE)
|
|
cmddata |= MMCCMD_INITCK;
|
|
|
|
switch (cmd->resp_type) {
|
|
case MMC_RSP_R1b:
|
|
cmddata |= MMCCMD_BSYEXP;
|
|
/* Fall-through */
|
|
case MMC_RSP_R1: /* R1, R1b, R5, R6, R7 */
|
|
cmddata |= MMCCMD_RSPFMT_R1567;
|
|
break;
|
|
case MMC_RSP_R2:
|
|
cmddata |= MMCCMD_RSPFMT_R2;
|
|
break;
|
|
case MMC_RSP_R3: /* R3, R4 */
|
|
cmddata |= MMCCMD_RSPFMT_R3;
|
|
break;
|
|
}
|
|
|
|
set_val(®s->mmcim, 0);
|
|
|
|
if (data) {
|
|
/* clear previous data transfer if any and set new one */
|
|
bytes_left = (data->blocksize * data->blocks);
|
|
|
|
/* Reset FIFO - Always use 32 byte fifo threshold */
|
|
set_val(®s->mmcfifoctl,
|
|
(MMCFIFOCTL_FIFOLEV | MMCFIFOCTL_FIFORST));
|
|
|
|
if (host->version == MMC_CTLR_VERSION_2)
|
|
cmddata |= MMCCMD_DMATRIG;
|
|
|
|
cmddata |= MMCCMD_WDATX;
|
|
if (data->flags == MMC_DATA_READ) {
|
|
set_val(®s->mmcfifoctl, MMCFIFOCTL_FIFOLEV);
|
|
} else if (data->flags == MMC_DATA_WRITE) {
|
|
set_val(®s->mmcfifoctl,
|
|
(MMCFIFOCTL_FIFOLEV |
|
|
MMCFIFOCTL_FIFODIR));
|
|
cmddata |= MMCCMD_DTRW;
|
|
}
|
|
|
|
set_val(®s->mmctod, 0xFFFF);
|
|
set_val(®s->mmcnblk, (data->blocks & MMCNBLK_NBLK_MASK));
|
|
set_val(®s->mmcblen, (data->blocksize & MMCBLEN_BLEN_MASK));
|
|
|
|
if (data->flags == MMC_DATA_WRITE) {
|
|
uint val;
|
|
data_buf = (char *)data->src;
|
|
/* For write, fill FIFO with data before issue of CMD */
|
|
for (i = 0; (i < fifo_words) && bytes_left; i++) {
|
|
memcpy((char *)&val, data_buf, 4);
|
|
set_val(®s->mmcdxr, val);
|
|
data_buf += 4;
|
|
bytes_left -= 4;
|
|
}
|
|
}
|
|
} else {
|
|
set_val(®s->mmcblen, 0);
|
|
set_val(®s->mmcnblk, 0);
|
|
}
|
|
|
|
set_val(®s->mmctor, 0x1FFF);
|
|
|
|
/* Send the command */
|
|
set_val(®s->mmcarghl, cmd->cmdarg);
|
|
set_val(®s->mmccmd, cmddata);
|
|
|
|
status_rdy = MMCST0_RSPDNE;
|
|
status_err = (MMCST0_TOUTRS | MMCST0_TOUTRD |
|
|
MMCST0_CRCWR | MMCST0_CRCRD);
|
|
if (cmd->resp_type & MMC_RSP_CRC)
|
|
status_err |= MMCST0_CRCRS;
|
|
|
|
mmcstatus = get_val(®s->mmcst0);
|
|
err = dmmc_check_status(regs, &mmcstatus, status_rdy, status_err);
|
|
if (err)
|
|
return err;
|
|
|
|
/* For R1b wait for busy done */
|
|
if (cmd->resp_type == MMC_RSP_R1b)
|
|
dmmc_busy_wait(regs);
|
|
|
|
/* Collect response from controller for specific commands */
|
|
if (mmcstatus & MMCST0_RSPDNE) {
|
|
/* Copy the response to the response buffer */
|
|
if (cmd->resp_type & MMC_RSP_136) {
|
|
cmd->response[0] = get_val(®s->mmcrsp67);
|
|
cmd->response[1] = get_val(®s->mmcrsp45);
|
|
cmd->response[2] = get_val(®s->mmcrsp23);
|
|
cmd->response[3] = get_val(®s->mmcrsp01);
|
|
} else if (cmd->resp_type & MMC_RSP_PRESENT) {
|
|
cmd->response[0] = get_val(®s->mmcrsp67);
|
|
}
|
|
}
|
|
|
|
if (data == NULL)
|
|
return 0;
|
|
|
|
if (data->flags == MMC_DATA_READ) {
|
|
/* check for DATDNE along with DRRDY as the controller might
|
|
* set the DATDNE without DRRDY for smaller transfers with
|
|
* less than FIFO threshold bytes
|
|
*/
|
|
status_rdy = MMCST0_DRRDY | MMCST0_DATDNE;
|
|
status_err = MMCST0_TOUTRD | MMCST0_CRCRD;
|
|
data_buf = data->dest;
|
|
} else {
|
|
status_rdy = MMCST0_DXRDY | MMCST0_DATDNE;
|
|
status_err = MMCST0_CRCWR;
|
|
}
|
|
|
|
/* Wait until all of the blocks are transferred */
|
|
while (bytes_left) {
|
|
err = dmmc_check_status(regs, &mmcstatus, status_rdy,
|
|
status_err);
|
|
if (err)
|
|
return err;
|
|
|
|
if (data->flags == MMC_DATA_READ) {
|
|
/*
|
|
* MMC controller sets the Data receive ready bit
|
|
* (DRRDY) in MMCST0 even before the entire FIFO is
|
|
* full. This results in erratic behavior if we start
|
|
* reading the FIFO soon after DRRDY. Wait for the
|
|
* FIFO full bit in MMCST1 for proper FIFO clearing.
|
|
*/
|
|
if (bytes_left > fifo_bytes)
|
|
dmmc_wait_fifo_status(regs, 0x4a);
|
|
else if (bytes_left == fifo_bytes) {
|
|
dmmc_wait_fifo_status(regs, 0x40);
|
|
if (cmd->cmdidx == MMC_CMD_SEND_EXT_CSD)
|
|
udelay(600);
|
|
}
|
|
|
|
for (i = 0; bytes_left && (i < fifo_words); i++) {
|
|
cmddata = get_val(®s->mmcdrr);
|
|
memcpy(data_buf, (char *)&cmddata, 4);
|
|
data_buf += 4;
|
|
bytes_left -= 4;
|
|
}
|
|
} else {
|
|
/*
|
|
* MMC controller sets the Data transmit ready bit
|
|
* (DXRDY) in MMCST0 even before the entire FIFO is
|
|
* empty. This results in erratic behavior if we start
|
|
* writing the FIFO soon after DXRDY. Wait for the
|
|
* FIFO empty bit in MMCST1 for proper FIFO clearing.
|
|
*/
|
|
dmmc_wait_fifo_status(regs, MMCST1_FIFOEMP);
|
|
for (i = 0; bytes_left && (i < fifo_words); i++) {
|
|
memcpy((char *)&cmddata, data_buf, 4);
|
|
set_val(®s->mmcdxr, cmddata);
|
|
data_buf += 4;
|
|
bytes_left -= 4;
|
|
}
|
|
dmmc_busy_wait(regs);
|
|
}
|
|
}
|
|
|
|
err = dmmc_check_status(regs, &mmcstatus, MMCST0_DATDNE, status_err);
|
|
if (err)
|
|
return err;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Initialize Davinci MMC controller */
|
|
#if !CONFIG_IS_ENABLED(DM_MMC)
|
|
static int dmmc_init(struct mmc *mmc)
|
|
{
|
|
struct davinci_mmc *host = mmc->priv;
|
|
#else
|
|
static int davinci_dm_mmc_init(struct udevice *dev)
|
|
{
|
|
struct davinci_mmc_priv *host = dev_get_priv(dev);
|
|
#endif
|
|
struct davinci_mmc_regs *regs = host->reg_base;
|
|
|
|
/* Clear status registers explicitly - soft reset doesn't clear it
|
|
* If Uboot is invoked from UBL with SDMMC Support, the status
|
|
* registers can have uncleared bits
|
|
*/
|
|
get_val(®s->mmcst0);
|
|
get_val(®s->mmcst1);
|
|
|
|
/* Hold software reset */
|
|
set_bit(®s->mmcctl, MMCCTL_DATRST);
|
|
set_bit(®s->mmcctl, MMCCTL_CMDRST);
|
|
udelay(10);
|
|
|
|
set_val(®s->mmcclk, 0x0);
|
|
set_val(®s->mmctor, 0x1FFF);
|
|
set_val(®s->mmctod, 0xFFFF);
|
|
|
|
/* Clear software reset */
|
|
clear_bit(®s->mmcctl, MMCCTL_DATRST);
|
|
clear_bit(®s->mmcctl, MMCCTL_CMDRST);
|
|
|
|
udelay(10);
|
|
|
|
/* Reset FIFO - Always use the maximum fifo threshold */
|
|
set_val(®s->mmcfifoctl, (MMCFIFOCTL_FIFOLEV | MMCFIFOCTL_FIFORST));
|
|
set_val(®s->mmcfifoctl, MMCFIFOCTL_FIFOLEV);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Set buswidth or clock as indicated by the MMC framework */
|
|
#if !CONFIG_IS_ENABLED(DM_MMC)
|
|
static int dmmc_set_ios(struct mmc *mmc)
|
|
{
|
|
struct davinci_mmc *host = mmc->priv;
|
|
struct davinci_mmc_regs *regs = host->reg_base;
|
|
#else
|
|
static int davinci_mmc_set_ios(struct udevice *dev)
|
|
{
|
|
struct mmc *mmc = mmc_get_mmc_dev(dev);
|
|
|
|
struct davinci_mmc_priv *host = dev_get_priv(dev);
|
|
struct davinci_mmc_regs *regs = host->reg_base;
|
|
#endif
|
|
/* Set the bus width */
|
|
if (mmc->bus_width == 4)
|
|
set_bit(®s->mmcctl, MMCCTL_WIDTH_4_BIT);
|
|
else
|
|
clear_bit(®s->mmcctl, MMCCTL_WIDTH_4_BIT);
|
|
|
|
/* Set clock speed */
|
|
if (mmc->clock) {
|
|
#if !CONFIG_IS_ENABLED(DM_MMC)
|
|
dmmc_set_clock(mmc, mmc->clock);
|
|
#else
|
|
davinci_mmc_set_clock(dev, mmc->clock);
|
|
#endif
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
#if !CONFIG_IS_ENABLED(DM_MMC)
|
|
static const struct mmc_ops dmmc_ops = {
|
|
.send_cmd = dmmc_send_cmd,
|
|
.set_ios = dmmc_set_ios,
|
|
.init = dmmc_init,
|
|
};
|
|
#else
|
|
|
|
static int davinci_mmc_getcd(struct udevice *dev)
|
|
{
|
|
int value = -1;
|
|
#if CONFIG_IS_ENABLED(DM_GPIO)
|
|
struct davinci_mmc_priv *priv = dev_get_priv(dev);
|
|
value = dm_gpio_get_value(&priv->cd_gpio);
|
|
#endif
|
|
/* if no CD return as 1 */
|
|
if (value < 0)
|
|
return 1;
|
|
|
|
return value;
|
|
}
|
|
|
|
static int davinci_mmc_getwp(struct udevice *dev)
|
|
{
|
|
int value = -1;
|
|
#if CONFIG_IS_ENABLED(DM_GPIO)
|
|
struct davinci_mmc_priv *priv = dev_get_priv(dev);
|
|
|
|
value = dm_gpio_get_value(&priv->wp_gpio);
|
|
#endif
|
|
/* if no WP return as 0 */
|
|
if (value < 0)
|
|
return 0;
|
|
|
|
return value;
|
|
}
|
|
|
|
static const struct dm_mmc_ops davinci_mmc_ops = {
|
|
.send_cmd = davinci_mmc_send_cmd,
|
|
.set_ios = davinci_mmc_set_ios,
|
|
.get_cd = davinci_mmc_getcd,
|
|
.get_wp = davinci_mmc_getwp,
|
|
};
|
|
#endif
|
|
|
|
#if !CONFIG_IS_ENABLED(DM_MMC)
|
|
/* Called from board_mmc_init during startup. Can be called multiple times
|
|
* depending on the number of slots available on board and controller
|
|
*/
|
|
int davinci_mmc_init(bd_t *bis, struct davinci_mmc *host)
|
|
{
|
|
host->cfg.name = "davinci";
|
|
host->cfg.ops = &dmmc_ops;
|
|
host->cfg.f_min = 200000;
|
|
host->cfg.f_max = 25000000;
|
|
host->cfg.voltages = host->voltages;
|
|
host->cfg.host_caps = host->host_caps;
|
|
|
|
host->cfg.b_max = DAVINCI_MAX_BLOCKS;
|
|
|
|
mmc_create(&host->cfg, host);
|
|
|
|
return 0;
|
|
}
|
|
#else
|
|
|
|
|
|
static int davinci_mmc_probe(struct udevice *dev)
|
|
{
|
|
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
|
|
struct davinci_mmc_plat *plat = dev_get_platdata(dev);
|
|
struct davinci_mmc_priv *priv = dev_get_priv(dev);
|
|
struct mmc_config *cfg = &plat->cfg;
|
|
struct davinci_of_data *data =
|
|
(struct davinci_of_data *)dev_get_driver_data(dev);
|
|
cfg->f_min = 200000;
|
|
cfg->f_max = 25000000;
|
|
cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
|
|
cfg->host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
|
|
cfg->b_max = DAVINCI_MAX_BLOCKS;
|
|
|
|
if (data) {
|
|
cfg->name = data->name;
|
|
priv->version = data->version;
|
|
}
|
|
|
|
priv->reg_base = (struct davinci_mmc_regs *)dev_read_addr(dev);
|
|
priv->input_clk = clk_get(DAVINCI_MMCSD_CLKID);
|
|
|
|
#if CONFIG_IS_ENABLED(DM_GPIO)
|
|
/* These GPIOs are optional */
|
|
gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, GPIOD_IS_IN);
|
|
gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio, GPIOD_IS_IN);
|
|
#endif
|
|
|
|
upriv->mmc = &plat->mmc;
|
|
|
|
return davinci_dm_mmc_init(dev);
|
|
}
|
|
|
|
static int davinci_mmc_bind(struct udevice *dev)
|
|
{
|
|
struct davinci_mmc_plat *plat = dev_get_platdata(dev);
|
|
|
|
return mmc_bind(dev, &plat->mmc, &plat->cfg);
|
|
}
|
|
|
|
|
|
const struct davinci_of_data davinci_mmc_host_info[] = {
|
|
{
|
|
.name = "dm6441-mmc",
|
|
.version = MMC_CTLR_VERSION_1,
|
|
},
|
|
{
|
|
.name = "da830-mmc",
|
|
.version = MMC_CTLR_VERSION_2,
|
|
},
|
|
{},
|
|
};
|
|
|
|
static const struct udevice_id davinci_mmc_ids[] = {
|
|
{
|
|
.compatible = "ti,dm6441-mmc",
|
|
.data = (ulong) &davinci_mmc_host_info[MMC_CTLR_VERSION_1]
|
|
},
|
|
{
|
|
.compatible = "ti,da830-mmc",
|
|
.data = (ulong) &davinci_mmc_host_info[MMC_CTLR_VERSION_2]
|
|
},
|
|
{},
|
|
};
|
|
|
|
U_BOOT_DRIVER(davinci_mmc_drv) = {
|
|
.name = "davinci_mmc",
|
|
.id = UCLASS_MMC,
|
|
.of_match = davinci_mmc_ids,
|
|
#if CONFIG_BLK
|
|
.bind = davinci_mmc_bind,
|
|
#endif
|
|
.probe = davinci_mmc_probe,
|
|
.ops = &davinci_mmc_ops,
|
|
.platdata_auto_alloc_size = sizeof(struct davinci_mmc_plat),
|
|
.priv_auto_alloc_size = sizeof(struct davinci_mmc_priv),
|
|
};
|
|
#endif
|