u-boot/board/freescale/corenet_ds/ddr.c
York Sun 939e5bf9b3 powerpc/mpc85xx: Display a warning for unsupported DDR data rates
If DDR initialziation uses a speed table and the speed is not matched,
print a warning message instead of silently ignoring.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00

261 lines
6.8 KiB
C

/*
* Copyright 2009-2011 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Fixed sdram init -- doesn't use serial presence detect.
*/
extern fixed_ddr_parm_t fixed_ddr_parm_0[];
#if (CONFIG_NUM_DDR_CONTROLLERS == 2)
extern fixed_ddr_parm_t fixed_ddr_parm_1[];
#endif
phys_size_t fixed_sdram(void)
{
int i;
char buf[32];
fsl_ddr_cfg_regs_t ddr_cfg_regs;
phys_size_t ddr_size;
unsigned int lawbar1_target_id;
ulong ddr_freq, ddr_freq_mhz;
ddr_freq = get_ddr_freq(0);
ddr_freq_mhz = ddr_freq / 1000000;
printf("Configuring DDR for %s MT/s data rate\n",
strmhz(buf, ddr_freq));
for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
(ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
memcpy(&ddr_cfg_regs,
fixed_ddr_parm_0[i].ddr_settings,
sizeof(ddr_cfg_regs));
break;
}
}
if (fixed_ddr_parm_0[i].max_freq == 0)
panic("Unsupported DDR data rate %s MT/s data rate\n",
strmhz(buf, ddr_freq));
ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN;
fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
#if (CONFIG_NUM_DDR_CONTROLLERS == 2)
memcpy(&ddr_cfg_regs,
fixed_ddr_parm_1[i].ddr_settings,
sizeof(ddr_cfg_regs));
ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN;
fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 1);
#endif
/*
* setup laws for DDR. If not interleaving, presuming half memory on
* DDR1 and the other half on DDR2
*/
if (fixed_ddr_parm_0[i].ddr_settings->cs[0].config & 0x20000000) {
if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
ddr_size,
LAW_TRGT_IF_DDR_INTRLV) < 0) {
printf("ERROR setting Local Access Windows for DDR\n");
return 0;
}
} else {
#if (CONFIG_NUM_DDR_CONTROLLERS == 2)
/* We require both controllers have identical DIMMs */
lawbar1_target_id = LAW_TRGT_IF_DDR_1;
if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
ddr_size / 2,
lawbar1_target_id) < 0) {
printf("ERROR setting Local Access Windows for DDR\n");
return 0;
}
lawbar1_target_id = LAW_TRGT_IF_DDR_2;
if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE + ddr_size / 2,
ddr_size / 2,
lawbar1_target_id) < 0) {
printf("ERROR setting Local Access Windows for DDR\n");
return 0;
}
#else
lawbar1_target_id = LAW_TRGT_IF_DDR_1;
if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
ddr_size,
lawbar1_target_id) < 0) {
printf("ERROR setting Local Access Windows for DDR\n");
return 0;
}
#endif
}
return ddr_size;
}
typedef struct {
u32 datarate_mhz_low;
u32 datarate_mhz_high;
u32 n_ranks;
u32 clk_adjust;
u32 wrlvl_start;
u32 cpo;
u32 write_data_delay;
u32 force_2T;
} board_specific_parameters_t;
/* ranges for parameters:
* wr_data_delay = 0-6
* clk adjust = 0-8
* cpo 2-0x1E (30)
*/
/* XXX: these values need to be checked for all interleaving modes. */
/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
* seem reliable, but errors will appear when memory intensive
* program is run. */
/* XXX: Single rank at 800 MHz is OK. */
const board_specific_parameters_t board_specific_parameters[][30] = {
{
/*
* memory controller 0
* lo| hi| num| clk| wrlvl | cpo |wrdata|2T
* mhz| mhz|ranks|adjst| start | delay|
*/
{ 0, 850, 4, 4, 6, 0xff, 2, 0},
{851, 950, 4, 5, 7, 0xff, 2, 0},
{951, 1050, 4, 5, 8, 0xff, 2, 0},
{1051, 1250, 4, 5, 10, 0xff, 2, 0},
{1251, 1350, 4, 5, 11, 0xff, 2, 0},
{ 0, 850, 2, 5, 6, 0xff, 2, 0},
{851, 950, 2, 5, 7, 0xff, 2, 0},
{951, 1050, 2, 5, 7, 0xff, 2, 0},
{1051, 1250, 2, 4, 6, 0xff, 2, 0},
{1251, 1350, 2, 5, 7, 0xff, 2, 0},
},
{
/*
* memory controller 1
* lo| hi| num| clk| wrlvl | cpo |wrdata|2T
* mhz| mhz|ranks|adjst| start | delay|
*/
{ 0, 850, 4, 4, 6, 0xff, 2, 0},
{851, 950, 4, 5, 7, 0xff, 2, 0},
{951, 1050, 4, 5, 8, 0xff, 2, 0},
{1051, 1250, 4, 5, 10, 0xff, 2, 0},
{1251, 1350, 4, 5, 11, 0xff, 2, 0},
{ 0, 850, 2, 5, 6, 0xff, 2, 0},
{851, 950, 2, 5, 7, 0xff, 2, 0},
{951, 1050, 2, 5, 7, 0xff, 2, 0},
{1051, 1250, 2, 4, 6, 0xff, 2, 0},
{1251, 1350, 2, 5, 7, 0xff, 2, 0},
}
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
const board_specific_parameters_t *pbsp =
&(board_specific_parameters[ctrl_num][0]);
u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
sizeof(board_specific_parameters[0][0]);
u32 i;
ulong ddr_freq;
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
for (i = 0; i < num_params; i++) {
if (ddr_freq >= pbsp->datarate_mhz_low &&
ddr_freq <= pbsp->datarate_mhz_high &&
pdimm[0].n_ranks == pbsp->n_ranks) {
popts->cpo_override = pbsp->cpo;
popts->write_data_delay = pbsp->write_data_delay;
popts->clk_adjust = pbsp->clk_adjust;
popts->wrlvl_start = pbsp->wrlvl_start;
popts->twoT_en = pbsp->force_2T;
break;
}
pbsp++;
}
if (i == num_params) {
printf("Warning: board specific timing not found "
"for data rate %lu MT/s!\n", ddr_freq);
}
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
/*
* Write leveling override
*/
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xf;
/*
* Rtt and Rtt_WR override
*/
popts->rtt_override = 0;
/* Enable ZQ calibration */
popts->zq_en = 1;
/* DHC_EN =1, ODT = 60 Ohm */
popts->ddr_cdr1 = DDR_CDR1_DHC_EN;
/* override SPD values. rcw_2 should vary at differnt speed */
if (pdimm[0].registered_dimm == 1) {
popts->rcw_override = 1;
popts->rcw_1 = 0x000a5a00;
if (ddr_freq <= 800)
popts->rcw_2 = 0x00000000;
else if (ddr_freq <= 1066)
popts->rcw_2 = 0x00100000;
else if (ddr_freq <= 1333)
popts->rcw_2 = 0x00200000;
else
popts->rcw_2 = 0x00300000;
}
}
phys_size_t initdram(int board_type)
{
phys_size_t dram_size;
puts("Initializing....");
if (fsl_use_spd()) {
puts("using SPD\n");
dram_size = fsl_ddr_sdram();
} else {
puts("using fixed parameters\n");
dram_size = fixed_sdram();
}
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
puts(" DDR: ");
return dram_size;
}