mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-27 15:12:21 +00:00
2ac07f75d1
This is based on the davinci da850evm. It can boot from either the on-board 16MB flash or from a microSD card. It also reads board information from an I2C EEPROM. The EV3 itself initally boots from write-protected EEPROM, so no u-boot SPL is needed. Signed-off-by: David Lechner <david@lechnology.com> Reviewed-by: Tom Rini <trini@konsulko.com>
176 lines
4 KiB
C
176 lines
4 KiB
C
/*
|
|
* Copyright (C) 2016 David Lechner <david@lechnology.com>
|
|
*
|
|
* Based on da850evm.c
|
|
*
|
|
* Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* Based on da830evm.c. Original Copyrights follow:
|
|
*
|
|
* Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
|
|
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <spi.h>
|
|
#include <spi_flash.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/arch/pinmux_defs.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/davinci_misc.h>
|
|
#include <asm/errno.h>
|
|
#include <hwconfig.h>
|
|
|
|
#ifdef CONFIG_DAVINCI_MMC
|
|
#include <mmc.h>
|
|
#include <asm/arch/sdmmc_defs.h>
|
|
#endif
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
u8 board_rev;
|
|
|
|
#define EEPROM_I2C_ADDR 0x50
|
|
#define EEPROM_REV_OFFSET 0x3F00
|
|
#define EEPROM_MAC_OFFSET 0x3F06
|
|
|
|
#ifdef CONFIG_DAVINCI_MMC
|
|
static struct davinci_mmc mmc_sd0 = {
|
|
.reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
|
|
.host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
|
|
.voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
|
|
.version = MMC_CTLR_VERSION_2,
|
|
};
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
mmc_sd0.input_clk = clk_get(DAVINCI_MMCSD_CLKID);
|
|
|
|
/* Add slot-0 to mmc subsystem */
|
|
return davinci_mmc_init(bis, &mmc_sd0);
|
|
}
|
|
#endif
|
|
|
|
const struct pinmux_resource pinmuxes[] = {
|
|
PINMUX_ITEM(spi0_pins_base),
|
|
PINMUX_ITEM(spi0_pins_scs0),
|
|
PINMUX_ITEM(uart1_pins_txrx),
|
|
PINMUX_ITEM(i2c0_pins),
|
|
PINMUX_ITEM(mmc0_pins),
|
|
};
|
|
|
|
const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
|
|
|
|
const struct lpsc_resource lpsc[] = {
|
|
{ DAVINCI_LPSC_SPI0 }, /* Serial Flash */
|
|
{ DAVINCI_LPSC_UART1 }, /* console */
|
|
{ DAVINCI_LPSC_MMC_SD },
|
|
};
|
|
|
|
const int lpsc_size = ARRAY_SIZE(lpsc);
|
|
|
|
u32 get_board_rev(void)
|
|
{
|
|
u8 buf[2];
|
|
|
|
if (!board_rev) {
|
|
if (i2c_read(EEPROM_I2C_ADDR, EEPROM_REV_OFFSET, 2, buf, 2)) {
|
|
printf("\nBoard revision read failed!\n");
|
|
} else {
|
|
/*
|
|
* Board rev 3 has MAC address at EEPROM_REV_OFFSET.
|
|
* Other revisions have checksum at EEPROM_REV_OFFSET+1
|
|
* to detect this.
|
|
*/
|
|
if ((buf[0] ^ buf[1]) == 0xFF)
|
|
board_rev = buf[0];
|
|
else
|
|
board_rev = 3;
|
|
}
|
|
}
|
|
|
|
return board_rev;
|
|
}
|
|
|
|
/*
|
|
* The Bluetooth MAC address serves as the board serial number.
|
|
*/
|
|
void get_board_serial(struct tag_serialnr *serialnr)
|
|
{
|
|
u32 offset;
|
|
u8 buf[6];
|
|
|
|
if (!board_rev)
|
|
board_rev = get_board_rev();
|
|
|
|
/* Board rev 3 has MAC address where rev should be */
|
|
offset = (board_rev == 3) ? EEPROM_REV_OFFSET : EEPROM_MAC_OFFSET;
|
|
|
|
if (i2c_read(EEPROM_I2C_ADDR, offset, 2, buf, 6)) {
|
|
printf("\nBoard serial read failed!\n");
|
|
} else {
|
|
u8 *nr;
|
|
|
|
nr = (u8 *)&serialnr->low;
|
|
nr[0] = buf[5];
|
|
nr[1] = buf[4];
|
|
nr[2] = buf[3];
|
|
nr[3] = buf[2];
|
|
nr = (u8 *)&serialnr->high;
|
|
nr[0] = buf[1];
|
|
nr[1] = buf[0];
|
|
nr[2] = 0;
|
|
nr[3] = 0;
|
|
}
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* Power on required peripherals
|
|
* ARM does not have access by default to PSC0 and PSC1
|
|
* assuming here that the DSP bootloader has set the IOPU
|
|
* such that PSC access is available to ARM
|
|
*/
|
|
if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
|
|
return 1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
#ifndef CONFIG_USE_IRQ
|
|
irq_init();
|
|
#endif
|
|
|
|
/* arch number of the board */
|
|
/* LEGO didn't register for a unique number and uses da850evm */
|
|
gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM;
|
|
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
|
|
|
|
/* setup the SUSPSRC for ARM to control emulation suspend */
|
|
writel(readl(&davinci_syscfg_regs->suspsrc) &
|
|
~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
|
|
DAVINCI_SYSCFG_SUSPSRC_SPI0 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
|
|
DAVINCI_SYSCFG_SUSPSRC_UART1),
|
|
&davinci_syscfg_regs->suspsrc);
|
|
|
|
/* configure pinmux settings */
|
|
if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
|
|
return 1;
|
|
|
|
/* enable the console UART */
|
|
writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
|
|
DAVINCI_UART_PWREMU_MGMT_UTRST),
|
|
&davinci_uart1_ctrl_regs->pwremu_mgmt);
|
|
|
|
return 0;
|
|
}
|