u-boot/board/firefly/roc-pc-rk3399/roc-pc-rk3399.c
Jagan Teki 6d06ea6c94 rockchip: roc-rk3399-pc: Set LED only during POR and pwr_key=y
ROC-RK3399-PC has specific set of configurations for
on-board led setup.

Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.

All this needs to happen only during power-on-reset not
for soft reset or WDT.

Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.

So, user need to press Power key only
- during POR
- pwr_key=y

Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-07-22 20:55:13 +08:00

78 lines
1.7 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2016 Rockchip Electronics Co., Ltd
*/
#include <common.h>
#include <dm.h>
#include <env.h>
#include <log.h>
#include <spl_gpio.h>
#include <asm/io.h>
#include <power/regulator.h>
#include <asm/arch-rockchip/cru.h>
#include <asm/arch-rockchip/gpio.h>
#include <asm/arch-rockchip/grf_rk3399.h>
#ifndef CONFIG_SPL_BUILD
int board_early_init_f(void)
{
struct udevice *regulator;
int ret;
ret = regulator_get_by_platname("vcc5v0_host", &regulator);
if (ret) {
debug("%s vcc5v0_host init fail! ret %d\n", __func__, ret);
goto out;
}
ret = regulator_set_enable(regulator, true);
if (ret)
debug("%s vcc5v0-host-en set fail! ret %d\n", __func__, ret);
out:
return 0;
}
#else
#define PMUGRF_BASE 0xff320000
#define GPIO0_BASE 0xff720000
/**
* LED setup for roc-rk3399-pc
*
* 1. Set the low power leds (only during POR, pwr_key env is 'y')
* glow yellow LED, termed as low power
* poll for on board power key press
* once powe key pressed, turn off yellow
* 2. Turn on red LED, indicating full power mode
*/
void led_setup(void)
{
struct rockchip_gpio_regs * const gpio0 = (void *)GPIO0_BASE;
struct rk3399_pmugrf_regs * const pmugrf = (void *)PMUGRF_BASE;
bool press_pwr_key = false;
if (IS_ENABLED(CONFIG_SPL_ENV_SUPPORT)) {
env_init();
env_load();
if (env_get_yesno("pwr_key") == 1)
press_pwr_key = true;
}
if (press_pwr_key && !strcmp(get_reset_cause(), "POR")) {
spl_gpio_output(gpio0, GPIO(BANK_A, 2), 1);
spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_A, 5),
GPIO_PULL_NORMAL);
while (readl(&gpio0->ext_port) & 0x20)
;
spl_gpio_output(gpio0, GPIO(BANK_A, 2), 0);
}
spl_gpio_output(gpio0, GPIO(BANK_B, 5), 1);
}
#endif