u-boot/include/configs/imx8mp_dhcom_pdk2.h
Tom Rini 9b5f9aeb3b Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BSS_MAX_SIZE
   CONFIG_SPL_MAX_FOOTPRINT

Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:10 -04:00

104 lines
3 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2022 Marek Vasut <marex@denx.de>
*/
#ifndef __IMX8MP_DHCOM_PDK2_H
#define __IMX8MP_DHCOM_PDK2_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>
#define CONFIG_SYS_BOOTM_LEN SZ_128M
#define CONFIG_SYS_MONITOR_LEN SZ_1M
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_STACK 0x96FC00
#define CONFIG_SPL_BSS_START_ADDR 0x0096FC00
#define CONFIG_SYS_SPL_MALLOC_START 0x4c000000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K /* 512 kiB */
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#endif
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x200000
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE 0x20000000 /* Minimum 512 MiB DDR */
#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
/* PHY needs a longer autonegotiation timeout after reset */
#define PHY_ANEG_TIMEOUT 20000
#define FEC_QUIRK_ENET_MAC
/* USDHC */
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#if !defined(CONFIG_SPL_BUILD)
#define CONFIG_EXTRA_ENV_SETTINGS \
"altbootcmd=run bootcmd ; reset\0" \
"bootlimit=3\0" \
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"pxefile_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"ramdisk_addr_r=0x58000000\0" \
"scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
/* Give slow devices beyond USB HUB chance to come up. */ \
"usb_pgood_delay=2000\0" \
"dfu_alt_info=" \
/* RAM block at DRAM offset 256..768 MiB */ \
"ram ram0=ram ram 0x50000000 0x20000000&" \
/* 16 MiB SPI NOR */ \
"mtd nor0=sf raw 0x0 0x1000000\0" \
"dh_update_env=" \
"setenv dh_update_env true ; saveenv ; saveenv\0" \
"dh_update_sf_gen_fcfb=" \
"setexpr sfaddr ${loadaddr} - 0x1000 ; " \
"base ${sfaddr} ; " \
"mw 0 0 0x400 ; " \
"mw 0x400 0x42464346 ; " \
"mw 0x404 0x56010000 ; " \
"mw 0x40c 00030300 ; " \
"mw 0x444 0x00020101 ; " \
"mw 0x450 0x10000000 ; " \
"mw 0x480 0x0818040b ; " \
"mw 0x484 0x24043008 ; " \
"mw 0x5c0 0x100 ; " \
"mw 0x5c4 0x10000 ; " \
"base 0\0" \
"dh_update_sf_write_data=" \
"setexpr sfaddr ${loadaddr} - 0x1000 ; " \
"setexpr filesize ${filesize} + 0x1000 ; " \
"sf probe && sf update ${sfaddr} 0 ${filesize}\0" \
"dh_update_sd_to_sf=" \
"load mmc 0:1 ${loadaddr} boot/flash.bin && " \
"run dh_update_sf_gen_fcfb dh_update_sf_write_data\0" \
"dh_update_emmc_to_sf=" \
"load mmc 1:1 ${loadaddr} boot/flash.bin && " \
"run dh_update_sf_gen_fcfb dh_update_sf_write_data\0" \
BOOTENV
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(MMC, mmc, 1) \
func(USB, usb, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#endif
#endif