u-boot/arch/arm/mach-mvebu/spl.c
Stefan Roese 09e89ab4af arm: mvebu: Add basic support for the Marvell Armada 375 SoC
This patch adds basic support for the Armada 375. Please note that
currently the SerDes and DDR3 init code for the A375 is not
included / enabled. This will be done in a later, follow-up patch.

Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:

=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-04-04 11:22:05 +02:00

124 lines
2.7 KiB
C

/*
* Copyright (C) 2014-2016 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <dm.h>
#include <debug_uart.h>
#include <fdtdec.h>
#include <spl.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
DECLARE_GLOBAL_DATA_PTR;
static u32 get_boot_device(void)
{
u32 val;
u32 boot_device;
/*
* First check, if UART boot-mode is active. This can only
* be done, via the bootrom error register. Here the
* MSB marks if the UART mode is active.
*/
val = readl(CONFIG_BOOTROM_ERR_REG);
boot_device = (val & BOOTROM_ERR_MODE_MASK) >> BOOTROM_ERR_MODE_OFFS;
debug("BOOTROM_REG=0x%08x boot_device=0x%x\n", val, boot_device);
if (boot_device == BOOTROM_ERR_MODE_UART)
return BOOT_DEVICE_UART;
/*
* Now check the SAR register for the strapped boot-device
*/
val = readl(CONFIG_SAR_REG); /* SAR - Sample At Reset */
boot_device = (val & BOOT_DEV_SEL_MASK) >> BOOT_DEV_SEL_OFFS;
debug("SAR_REG=0x%08x boot_device=0x%x\n", val, boot_device);
switch (boot_device) {
#ifdef CONFIG_SPL_MMC_SUPPORT
case BOOT_FROM_MMC:
case BOOT_FROM_MMC_ALT:
return BOOT_DEVICE_MMC1;
#endif
case BOOT_FROM_UART:
return BOOT_DEVICE_UART;
case BOOT_FROM_SPI:
default:
return BOOT_DEVICE_SPI;
};
}
u32 spl_boot_device(void)
{
return get_boot_device();
}
#ifdef CONFIG_SPL_MMC_SUPPORT
u32 spl_boot_mode(void)
{
return MMCSD_MODE_RAW;
}
#endif
void board_init_f(ulong dummy)
{
int ret;
/*
* Pin muxing needs to be done before UART output, since
* on A38x the UART pins need some re-muxing for output
* to work.
*/
board_early_init_f();
/* Example code showing how to enable the debug UART on MVEBU */
#ifdef EARLY_UART
/*
* Debug UART can be used from here if required:
*
* debug_uart_init();
* printch('a');
* printhex8(0x1234);
* printascii("string");
*/
#endif
ret = spl_init();
if (ret) {
debug("spl_init() failed: %d\n", ret);
hang();
}
/* Use special translation offset for SPL */
dm_set_translation_offset(0xd0000000 - 0xf1000000);
preloader_console_init();
timer_init();
/* Armada 375 does not support SerDes and DDR3 init yet */
#if !defined(CONFIG_ARMADA_375)
/* First init the serdes PHY's */
serdes_phy_config();
/* Setup DDR */
ddr3_init();
#endif
/*
* Return to the BootROM to continue the Marvell xmodem
* UART boot protocol. As initiated by the kwboot tool.
*
* This can only be done by the BootROM and not by the
* U-Boot SPL infrastructure, since the beginning of the
* image is already read and interpreted by the BootROM.
* SPL has no chance to receive this information. So we
* need to return to the BootROM to enable this xmodem
* UART download.
*/
if (get_boot_device() == BOOT_DEVICE_UART)
return_to_bootrom();
}