mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-15 01:17:39 +00:00
efda93c6b5
There is little need to print the devstat information or when we exit a function during a typical boot. Remove them to reduce the noise during typical operation Signed-off-by: Bryan Brattlof <bb@ti.com>
285 lines
7.2 KiB
C
285 lines
7.2 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* AM62A7: SoC specific initialization
|
|
*
|
|
* Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
|
|
*/
|
|
|
|
#include <spl.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include "sysfw-loader.h"
|
|
#include "common.h"
|
|
#include <dm.h>
|
|
#include <dm/uclass-internal.h>
|
|
#include <dm/pinctrl.h>
|
|
|
|
struct fwl_data cbass_main_fwls[] = {
|
|
{ "FSS_DAT_REG3", 7, 8 },
|
|
};
|
|
|
|
/*
|
|
* This uninitialized global variable would normal end up in the .bss section,
|
|
* but the .bss is cleared between writing and reading this variable, so move
|
|
* it to the .data section.
|
|
*/
|
|
u32 bootindex __section(".data");
|
|
static struct rom_extended_boot_data bootdata __section(".data");
|
|
|
|
static void store_boot_info_from_rom(void)
|
|
{
|
|
bootindex = *(u32 *)(CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX);
|
|
|
|
if (IS_ENABLED(CONFIG_CPU_V7R)) {
|
|
memcpy(&bootdata, (uintptr_t *)ROM_ENTENDED_BOOT_DATA_INFO,
|
|
sizeof(struct rom_extended_boot_data));
|
|
}
|
|
}
|
|
|
|
static void ctrl_mmr_unlock(void)
|
|
{
|
|
/* Unlock all WKUP_CTRL_MMR0 module registers */
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 0);
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 1);
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 2);
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 3);
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 4);
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 5);
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 6);
|
|
mmr_unlock(WKUP_CTRL_MMR0_BASE, 7);
|
|
|
|
/* Unlock all CTRL_MMR0 module registers */
|
|
mmr_unlock(CTRL_MMR0_BASE, 0);
|
|
mmr_unlock(CTRL_MMR0_BASE, 1);
|
|
mmr_unlock(CTRL_MMR0_BASE, 2);
|
|
mmr_unlock(CTRL_MMR0_BASE, 4);
|
|
mmr_unlock(CTRL_MMR0_BASE, 5);
|
|
mmr_unlock(CTRL_MMR0_BASE, 6);
|
|
|
|
/* Unlock all MCU_CTRL_MMR0 module registers */
|
|
mmr_unlock(MCU_CTRL_MMR0_BASE, 0);
|
|
mmr_unlock(MCU_CTRL_MMR0_BASE, 1);
|
|
mmr_unlock(MCU_CTRL_MMR0_BASE, 2);
|
|
mmr_unlock(MCU_CTRL_MMR0_BASE, 3);
|
|
mmr_unlock(MCU_CTRL_MMR0_BASE, 4);
|
|
mmr_unlock(MCU_CTRL_MMR0_BASE, 6);
|
|
|
|
/* Unlock PADCFG_CTRL_MMR padconf registers */
|
|
mmr_unlock(PADCFG_MMR0_BASE, 1);
|
|
mmr_unlock(PADCFG_MMR1_BASE, 1);
|
|
}
|
|
|
|
#if (IS_ENABLED(CONFIG_CPU_V7R))
|
|
static void setup_qos(void)
|
|
{
|
|
u32 i;
|
|
|
|
for (i = 0; i < am62a_qos_count; i++)
|
|
writel(am62a_qos_data[i].val, (uintptr_t)am62a_qos_data[i].reg);
|
|
}
|
|
#else
|
|
static void setup_qos(void)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
#if defined(CONFIG_CPU_V7R)
|
|
setup_k3_mpu_regions();
|
|
#endif
|
|
|
|
/*
|
|
* Cannot delay this further as there is a chance that
|
|
* K3_BOOT_PARAM_TABLE_INDEX can be over written by SPL MALLOC section.
|
|
*/
|
|
store_boot_info_from_rom();
|
|
|
|
ctrl_mmr_unlock();
|
|
|
|
/* Init DM early */
|
|
spl_early_init();
|
|
|
|
/*
|
|
* Process pinctrl for the serial0 and serial3, aka WKUP_UART0 and
|
|
* MAIN_UART1 modules and continue regardless of the result of pinctrl.
|
|
* Do this without probing the device, but instead by searching the
|
|
* device that would request the given sequence number if probed. The
|
|
* UARTs will be used by the DM firmware and TIFS firmware images
|
|
* respectively and the firmware depend on SPL to initialize the pin
|
|
* settings.
|
|
*/
|
|
ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, &dev);
|
|
if (!ret)
|
|
pinctrl_select_state(dev, "default");
|
|
|
|
ret = uclass_find_device_by_seq(UCLASS_SERIAL, 3, &dev);
|
|
if (!ret)
|
|
pinctrl_select_state(dev, "default");
|
|
|
|
#ifdef CONFIG_K3_EARLY_CONS
|
|
/*
|
|
* Allow establishing an early console as required for example when
|
|
* doing a UART-based boot. Note that this console may not "survive"
|
|
* through a SYSFW PM-init step and will need a re-init in some way
|
|
* due to changing module clock frequencies.
|
|
*/
|
|
early_console_init();
|
|
#endif
|
|
|
|
#if defined(CONFIG_K3_LOAD_SYSFW)
|
|
/*
|
|
* Configure and start up system controller firmware. Provide
|
|
* the U-Boot console init function to the SYSFW post-PM configuration
|
|
* callback hook, effectively switching on (or over) the console
|
|
* output.
|
|
*/
|
|
ret = is_rom_loaded_sysfw(&bootdata);
|
|
if (!ret)
|
|
panic("ROM has not loaded TIFS firmware\n");
|
|
|
|
k3_sysfw_loader(true, NULL, NULL);
|
|
#endif
|
|
|
|
#if defined(CONFIG_CPU_V7R)
|
|
/*
|
|
* Relocate boot information to OCRAM (after TIFS has opend this
|
|
* region for us) so the next bootloader stages can keep access to
|
|
* primary vs backup bootmodes.
|
|
*/
|
|
writel(bootindex, K3_BOOT_PARAM_TABLE_INDEX_OCRAM);
|
|
#endif
|
|
|
|
/*
|
|
* Force probe of clk_k3 driver here to ensure basic default clock
|
|
* configuration is always done.
|
|
*/
|
|
if (IS_ENABLED(CONFIG_SPL_CLK_K3)) {
|
|
ret = uclass_get_device_by_driver(UCLASS_CLK,
|
|
DM_DRIVER_GET(ti_clk),
|
|
&dev);
|
|
if (ret)
|
|
printf("Failed to initialize clk-k3!\n");
|
|
}
|
|
|
|
preloader_console_init();
|
|
|
|
/* Output System Firmware version info */
|
|
k3_sysfw_print_ver();
|
|
|
|
/* Disable ROM configured firewalls right after loading sysfw */
|
|
remove_fwl_configs(cbass_main_fwls, ARRAY_SIZE(cbass_main_fwls));
|
|
|
|
#if defined(CONFIG_K3_AM62A_DDRSS)
|
|
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
|
|
if (ret)
|
|
panic("DRAM init failed: %d\n", ret);
|
|
#endif
|
|
|
|
setup_qos();
|
|
|
|
debug("am62a_init: %s done\n", __func__);
|
|
}
|
|
|
|
static u32 __get_backup_bootmedia(u32 devstat)
|
|
{
|
|
u32 bkup_bootmode = (devstat & MAIN_DEVSTAT_BACKUP_BOOTMODE_MASK) >>
|
|
MAIN_DEVSTAT_BACKUP_BOOTMODE_SHIFT;
|
|
u32 bkup_bootmode_cfg =
|
|
(devstat & MAIN_DEVSTAT_BACKUP_BOOTMODE_CFG_MASK) >>
|
|
MAIN_DEVSTAT_BACKUP_BOOTMODE_CFG_SHIFT;
|
|
|
|
switch (bkup_bootmode) {
|
|
case BACKUP_BOOT_DEVICE_UART:
|
|
return BOOT_DEVICE_UART;
|
|
|
|
case BACKUP_BOOT_DEVICE_USB:
|
|
return BOOT_DEVICE_USB;
|
|
|
|
case BACKUP_BOOT_DEVICE_ETHERNET:
|
|
return BOOT_DEVICE_ETHERNET;
|
|
|
|
case BACKUP_BOOT_DEVICE_MMC:
|
|
if (bkup_bootmode_cfg)
|
|
return BOOT_DEVICE_MMC2;
|
|
return BOOT_DEVICE_MMC1;
|
|
|
|
case BACKUP_BOOT_DEVICE_SPI:
|
|
return BOOT_DEVICE_SPI;
|
|
|
|
case BACKUP_BOOT_DEVICE_I2C:
|
|
return BOOT_DEVICE_I2C;
|
|
|
|
case BACKUP_BOOT_DEVICE_DFU:
|
|
if (bkup_bootmode_cfg & MAIN_DEVSTAT_BACKUP_USB_MODE_MASK)
|
|
return BOOT_DEVICE_USB;
|
|
return BOOT_DEVICE_DFU;
|
|
};
|
|
|
|
return BOOT_DEVICE_RAM;
|
|
}
|
|
|
|
static u32 __get_primary_bootmedia(u32 devstat)
|
|
{
|
|
u32 bootmode = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_MASK) >>
|
|
MAIN_DEVSTAT_PRIMARY_BOOTMODE_SHIFT;
|
|
u32 bootmode_cfg = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_MASK) >>
|
|
MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_SHIFT;
|
|
|
|
switch (bootmode) {
|
|
case BOOT_DEVICE_OSPI:
|
|
fallthrough;
|
|
case BOOT_DEVICE_QSPI:
|
|
fallthrough;
|
|
case BOOT_DEVICE_XSPI:
|
|
fallthrough;
|
|
case BOOT_DEVICE_SPI:
|
|
return BOOT_DEVICE_SPI;
|
|
|
|
case BOOT_DEVICE_ETHERNET_RGMII:
|
|
fallthrough;
|
|
case BOOT_DEVICE_ETHERNET_RMII:
|
|
return BOOT_DEVICE_ETHERNET;
|
|
|
|
case BOOT_DEVICE_EMMC:
|
|
return BOOT_DEVICE_MMC1;
|
|
|
|
case BOOT_DEVICE_SPI_NAND:
|
|
return BOOT_DEVICE_SPINAND;
|
|
|
|
case BOOT_DEVICE_MMC:
|
|
if ((bootmode_cfg & MAIN_DEVSTAT_PRIMARY_MMC_PORT_MASK) >>
|
|
MAIN_DEVSTAT_PRIMARY_MMC_PORT_SHIFT)
|
|
return BOOT_DEVICE_MMC2;
|
|
return BOOT_DEVICE_MMC1;
|
|
|
|
case BOOT_DEVICE_DFU:
|
|
if ((bootmode_cfg & MAIN_DEVSTAT_PRIMARY_USB_MODE_MASK) >>
|
|
MAIN_DEVSTAT_PRIMARY_USB_MODE_SHIFT)
|
|
return BOOT_DEVICE_USB;
|
|
return BOOT_DEVICE_DFU;
|
|
|
|
case BOOT_DEVICE_NOBOOT:
|
|
return BOOT_DEVICE_RAM;
|
|
}
|
|
|
|
return bootmode;
|
|
}
|
|
|
|
u32 spl_boot_device(void)
|
|
{
|
|
u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT);
|
|
u32 bootmedia;
|
|
|
|
if (bootindex == K3_PRIMARY_BOOTMODE)
|
|
bootmedia = __get_primary_bootmedia(devstat);
|
|
else
|
|
bootmedia = __get_backup_bootmedia(devstat);
|
|
|
|
debug("am62a_init: %s: devstat = 0x%x bootmedia = 0x%x bootindex = %d\n",
|
|
__func__, devstat, bootmedia, bootindex);
|
|
return bootmedia;
|
|
}
|