u-boot/drivers/hwmon/lm75.c
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

143 lines
3.1 KiB
C

/*
* (C) Copyright 2001
* Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* On Semiconductor's LM75 Temperature Sensor
*/
#include <common.h>
#include <i2c.h>
#include <dtt.h>
/*
* Device code
*/
#if defined(CONFIG_SYS_I2C_DTT_ADDR)
#define DTT_I2C_DEV_CODE CONFIG_SYS_I2C_DTT_ADDR
#else
#define DTT_I2C_DEV_CODE 0x48 /* ON Semi's LM75 device */
#endif
#define DTT_READ_TEMP 0x0
#define DTT_CONFIG 0x1
#define DTT_TEMP_HYST 0x2
#define DTT_TEMP_SET 0x3
int dtt_read(int sensor, int reg)
{
int dlen;
uchar data[2];
#ifdef CONFIG_DTT_AD7414
/*
* On AD7414 the first value upon bootup is not read correctly.
* This is most likely because of the 800ms update time of the
* temp register in normal update mode. To get current values
* each time we issue the "dtt" command including upon powerup
* we switch into one-short mode.
*
* Issue one-shot mode command
*/
dtt_write(sensor, DTT_CONFIG, 0x64);
#endif
/* Validate 'reg' param */
if((reg < 0) || (reg > 3))
return -1;
/* Calculate sensor address and register. */
sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
/* Prepare to handle 2 byte result. */
if ((reg == DTT_READ_TEMP) ||
(reg == DTT_TEMP_HYST) ||
(reg == DTT_TEMP_SET))
dlen = 2;
else
dlen = 1;
/* Now try to read the register. */
if (i2c_read(sensor, reg, 1, data, dlen) != 0)
return -1;
/* Handle 2 byte result. */
if (dlen == 2)
return ((int)((short)data[1] + (((short)data[0]) << 8)));
return (int)data[0];
} /* dtt_read() */
int dtt_write(int sensor, int reg, int val)
{
int dlen;
uchar data[2];
/* Validate 'reg' param */
if ((reg < 0) || (reg > 3))
return 1;
/* Calculate sensor address and register. */
sensor = DTT_I2C_DEV_CODE + (sensor & 0x07);
/* Handle 2 byte values. */
if ((reg == DTT_READ_TEMP) ||
(reg == DTT_TEMP_HYST) ||
(reg == DTT_TEMP_SET)) {
dlen = 2;
data[0] = (char)((val >> 8) & 0xff); /* MSB first */
data[1] = (char)(val & 0xff);
} else {
dlen = 1;
data[0] = (char)(val & 0xff);
}
/* Write value to register. */
if (i2c_write(sensor, reg, 1, data, dlen) != 0)
return 1;
return 0;
} /* dtt_write() */
int dtt_init_one(int sensor)
{
int val;
/* Setup TSET ( trip point ) register */
val = ((CONFIG_SYS_DTT_MAX_TEMP * 2) << 7) & 0xff80; /* trip */
if (dtt_write(sensor, DTT_TEMP_SET, val) != 0)
return 1;
/* Setup THYST ( untrip point ) register - Hysteresis */
val = (((CONFIG_SYS_DTT_MAX_TEMP - CONFIG_SYS_DTT_HYSTERESIS) * 2) << 7) & 0xff80;
if (dtt_write(sensor, DTT_TEMP_HYST, val) != 0)
return 1;
/* Setup configuraton register */
#ifdef CONFIG_DTT_AD7414
/* config = alert active low and disabled */
val = 0x60;
#else
/* config = 6 sample integration, int mode, active low, and enable */
val = 0x18;
#endif
if (dtt_write(sensor, DTT_CONFIG, val) != 0)
return 1;
return 0;
} /* dtt_init_one() */
int dtt_get_temp(int sensor)
{
int const ret = dtt_read(sensor, DTT_READ_TEMP);
if (ret < 0) {
printf("DTT temperature read failed.\n");
return 0;
}
return (int)((int16_t) ret / 256);
} /* dtt_get_temp() */