u-boot/drivers/mtd/spi/sf_internal.h
Jagannadha Sutradharudu Teki 54ba653ab6 sf: Enable byte program support
Enabled byte program support for sst flashes in sf.

Few controllers will only support BP, so this patch gives
a tx transfer flag to set the BP so-that sf will operate
on byte program transfer.

A new TX operation mode SPI_OPM_TX_BP is introduced for such SPI
controller to use byte program op for SST flash.

Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2014-12-13 15:08:04 -07:00

224 lines
6.3 KiB
C

/*
* SPI flash internal definitions
*
* Copyright (C) 2008 Atmel Corporation
* Copyright (C) 2013 Jagannadha Sutradharudu Teki, Xilinx Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SF_INTERNAL_H_
#define _SF_INTERNAL_H_
#include <linux/types.h>
#include <linux/compiler.h>
/* Dual SPI flash memories - see SPI_COMM_DUAL_... */
enum spi_dual_flash {
SF_SINGLE_FLASH = 0,
SF_DUAL_STACKED_FLASH = 1 << 0,
SF_DUAL_PARALLEL_FLASH = 1 << 1,
};
/* Enum list - Full read commands */
enum spi_read_cmds {
ARRAY_SLOW = 1 << 0,
ARRAY_FAST = 1 << 1,
DUAL_OUTPUT_FAST = 1 << 2,
DUAL_IO_FAST = 1 << 3,
QUAD_OUTPUT_FAST = 1 << 4,
QUAD_IO_FAST = 1 << 5,
};
/* Normal - Extended - Full command set */
#define RD_NORM (ARRAY_SLOW | ARRAY_FAST)
#define RD_EXTN (RD_NORM | DUAL_OUTPUT_FAST | DUAL_IO_FAST)
#define RD_FULL (RD_EXTN | QUAD_OUTPUT_FAST | QUAD_IO_FAST)
/* sf param flags */
enum {
SECT_4K = 1 << 0,
SECT_32K = 1 << 1,
E_FSR = 1 << 2,
SST_BP = 1 << 3,
SST_WP = 1 << 4,
WR_QPP = 1 << 5,
};
#define SST_WR (SST_BP | SST_WP)
#define SPI_FLASH_3B_ADDR_LEN 3
#define SPI_FLASH_CMD_LEN (1 + SPI_FLASH_3B_ADDR_LEN)
#define SPI_FLASH_16MB_BOUN 0x1000000
/* CFI Manufacture ID's */
#define SPI_FLASH_CFI_MFR_SPANSION 0x01
#define SPI_FLASH_CFI_MFR_STMICRO 0x20
#define SPI_FLASH_CFI_MFR_MACRONIX 0xc2
#define SPI_FLASH_CFI_MFR_WINBOND 0xef
/* Erase commands */
#define CMD_ERASE_4K 0x20
#define CMD_ERASE_32K 0x52
#define CMD_ERASE_CHIP 0xc7
#define CMD_ERASE_64K 0xd8
/* Write commands */
#define CMD_WRITE_STATUS 0x01
#define CMD_PAGE_PROGRAM 0x02
#define CMD_WRITE_DISABLE 0x04
#define CMD_READ_STATUS 0x05
#define CMD_QUAD_PAGE_PROGRAM 0x32
#define CMD_READ_STATUS1 0x35
#define CMD_WRITE_ENABLE 0x06
#define CMD_READ_CONFIG 0x35
#define CMD_FLAG_STATUS 0x70
/* Read commands */
#define CMD_READ_ARRAY_SLOW 0x03
#define CMD_READ_ARRAY_FAST 0x0b
#define CMD_READ_DUAL_OUTPUT_FAST 0x3b
#define CMD_READ_DUAL_IO_FAST 0xbb
#define CMD_READ_QUAD_OUTPUT_FAST 0x6b
#define CMD_READ_QUAD_IO_FAST 0xeb
#define CMD_READ_ID 0x9f
/* Bank addr access commands */
#ifdef CONFIG_SPI_FLASH_BAR
# define CMD_BANKADDR_BRWR 0x17
# define CMD_BANKADDR_BRRD 0x16
# define CMD_EXTNADDR_WREAR 0xC5
# define CMD_EXTNADDR_RDEAR 0xC8
#endif
/* Common status */
#define STATUS_WIP (1 << 0)
#define STATUS_QEB_WINSPAN (1 << 1)
#define STATUS_QEB_MXIC (1 << 6)
#define STATUS_PEC (1 << 7)
#ifdef CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
#define STATUS_SRWD (1 << 7) /* SR write protect */
#endif
/* Flash timeout values */
#define SPI_FLASH_PROG_TIMEOUT (2 * CONFIG_SYS_HZ)
#define SPI_FLASH_PAGE_ERASE_TIMEOUT (5 * CONFIG_SYS_HZ)
#define SPI_FLASH_SECTOR_ERASE_TIMEOUT (10 * CONFIG_SYS_HZ)
/* SST specific */
#ifdef CONFIG_SPI_FLASH_SST
# define CMD_SST_BP 0x02 /* Byte Program */
# define CMD_SST_AAI_WP 0xAD /* Auto Address Incr Word Program */
int sst_write_wp(struct spi_flash *flash, u32 offset, size_t len,
const void *buf);
int sst_write_bp(struct spi_flash *flash, u32 offset, size_t len,
const void *buf);
#endif
/**
* struct spi_flash_params - SPI/QSPI flash device params structure
*
* @name: Device name ([MANUFLETTER][DEVTYPE][DENSITY][EXTRAINFO])
* @jedec: Device jedec ID (0x[1byte_manuf_id][2byte_dev_id])
* @ext_jedec: Device ext_jedec ID
* @sector_size: Sector size of this device
* @nr_sectors: No.of sectors on this device
* @e_rd_cmd: Enum list for read commands
* @flags: Important param, for flash specific behaviour
*/
struct spi_flash_params {
const char *name;
u32 jedec;
u16 ext_jedec;
u32 sector_size;
u32 nr_sectors;
u8 e_rd_cmd;
u16 flags;
};
extern const struct spi_flash_params spi_flash_params_table[];
/* Send a single-byte command to the device and read the response */
int spi_flash_cmd(struct spi_slave *spi, u8 cmd, void *response, size_t len);
/*
* Send a multi-byte command to the device and read the response. Used
* for flash array reads, etc.
*/
int spi_flash_cmd_read(struct spi_slave *spi, const u8 *cmd,
size_t cmd_len, void *data, size_t data_len);
/*
* Send a multi-byte command to the device followed by (optional)
* data. Used for programming the flash array, etc.
*/
int spi_flash_cmd_write(struct spi_slave *spi, const u8 *cmd, size_t cmd_len,
const void *data, size_t data_len);
/* Flash erase(sectors) operation, support all possible erase commands */
int spi_flash_cmd_erase_ops(struct spi_flash *flash, u32 offset, size_t len);
/* Read the status register */
int spi_flash_cmd_read_status(struct spi_flash *flash, u8 *rs);
/* Program the status register */
int spi_flash_cmd_write_status(struct spi_flash *flash, u8 ws);
/* Read the config register */
int spi_flash_cmd_read_config(struct spi_flash *flash, u8 *rc);
/* Program the config register */
int spi_flash_cmd_write_config(struct spi_flash *flash, u8 wc);
/* Enable writing on the SPI flash */
static inline int spi_flash_cmd_write_enable(struct spi_flash *flash)
{
return spi_flash_cmd(flash->spi, CMD_WRITE_ENABLE, NULL, 0);
}
/* Disable writing on the SPI flash */
static inline int spi_flash_cmd_write_disable(struct spi_flash *flash)
{
return spi_flash_cmd(flash->spi, CMD_WRITE_DISABLE, NULL, 0);
}
/*
* Send the read status command to the device and wait for the wip
* (write-in-progress) bit to clear itself.
*/
int spi_flash_cmd_wait_ready(struct spi_flash *flash, unsigned long timeout);
/*
* Used for spi_flash write operation
* - SPI claim
* - spi_flash_cmd_write_enable
* - spi_flash_cmd_write
* - spi_flash_cmd_wait_ready
* - SPI release
*/
int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd,
size_t cmd_len, const void *buf, size_t buf_len);
/*
* Flash write operation, support all possible write commands.
* Write the requested data out breaking it up into multiple write
* commands as needed per the write size.
*/
int spi_flash_cmd_write_ops(struct spi_flash *flash, u32 offset,
size_t len, const void *buf);
/*
* Same as spi_flash_cmd_read() except it also claims/releases the SPI
* bus. Used as common part of the ->read() operation.
*/
int spi_flash_read_common(struct spi_flash *flash, const u8 *cmd,
size_t cmd_len, void *data, size_t data_len);
/* Flash read operation, support all possible read commands */
int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
size_t len, void *data);
#endif /* _SF_INTERNAL_H_ */