mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-30 06:53:09 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
163 lines
3.7 KiB
C
163 lines
3.7 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2009
|
|
* Net Insight <www.netinsight.net>
|
|
* Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
|
*
|
|
* Based on sheevaplug.c:
|
|
* (C) Copyright 2009
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <miiphy.h>
|
|
#include <net.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/arch/mpp.h>
|
|
#include "openrd.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* default gpio configuration
|
|
* There are maximum 64 gpios controlled through 2 sets of registers
|
|
* the below configuration configures mainly initial LED status
|
|
*/
|
|
mvebu_config_gpio(OPENRD_OE_VAL_LOW,
|
|
OPENRD_OE_VAL_HIGH,
|
|
OPENRD_OE_LOW, OPENRD_OE_HIGH);
|
|
|
|
/* Multi-Purpose Pins Functionality configuration */
|
|
static const u32 kwmpp_config[] = {
|
|
MPP0_NF_IO2,
|
|
MPP1_NF_IO3,
|
|
MPP2_NF_IO4,
|
|
MPP3_NF_IO5,
|
|
MPP4_NF_IO6,
|
|
MPP5_NF_IO7,
|
|
MPP6_SYSRST_OUTn,
|
|
MPP7_GPO,
|
|
MPP8_TW_SDA,
|
|
MPP9_TW_SCK,
|
|
MPP10_UART0_TXD,
|
|
MPP11_UART0_RXD,
|
|
MPP12_SD_CLK,
|
|
MPP13_SD_CMD, /* Alt UART1_TXD */
|
|
MPP14_SD_D0, /* Alt UART1_RXD */
|
|
MPP15_SD_D1,
|
|
MPP16_SD_D2,
|
|
MPP17_SD_D3,
|
|
MPP18_NF_IO0,
|
|
MPP19_NF_IO1,
|
|
MPP20_GE1_0,
|
|
MPP21_GE1_1,
|
|
MPP22_GE1_2,
|
|
MPP23_GE1_3,
|
|
MPP24_GE1_4,
|
|
MPP25_GE1_5,
|
|
MPP26_GE1_6,
|
|
MPP27_GE1_7,
|
|
MPP28_GPIO,
|
|
MPP29_TSMP9,
|
|
MPP30_GE1_10,
|
|
MPP31_GE1_11,
|
|
MPP32_GE1_12,
|
|
MPP33_GE1_13,
|
|
MPP34_GPIO, /* UART1 / SD sel */
|
|
MPP35_TDM_CH0_TX_QL,
|
|
MPP36_TDM_SPI_CS1,
|
|
MPP37_TDM_CH2_TX_QL,
|
|
MPP38_TDM_CH2_RX_QL,
|
|
MPP39_AUDIO_I2SBCLK,
|
|
MPP40_AUDIO_I2SDO,
|
|
MPP41_AUDIO_I2SLRC,
|
|
MPP42_AUDIO_I2SMCLK,
|
|
MPP43_AUDIO_I2SDI,
|
|
MPP44_AUDIO_EXTCLK,
|
|
MPP45_TDM_PCLK,
|
|
MPP46_TDM_FS,
|
|
MPP47_TDM_DRX,
|
|
MPP48_TDM_DTX,
|
|
MPP49_TDM_CH0_RX_QL,
|
|
0
|
|
};
|
|
|
|
kirkwood_mpp_conf(kwmpp_config, NULL);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/*
|
|
* arch number of board
|
|
*/
|
|
#if defined(CONFIG_BOARD_IS_OPENRD_BASE)
|
|
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
|
|
#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT)
|
|
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT;
|
|
#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
|
|
gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE;
|
|
#endif
|
|
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_RESET_PHY_R
|
|
/* Configure and enable MV88E1116/88E1121 PHY */
|
|
void mv_phy_init(char *name)
|
|
{
|
|
u16 reg;
|
|
u16 devadr;
|
|
|
|
if (miiphy_set_current_dev(name))
|
|
return;
|
|
|
|
/* command to read PHY dev address */
|
|
if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) {
|
|
printf("Err..%s could not read PHY dev address\n", __func__);
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Enable RGMII delay on Tx and Rx for CPU port
|
|
* Ref: sec 4.7.2 of chip datasheet
|
|
*/
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
|
|
miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
|
|
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
|
|
miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
|
|
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
|
|
|
|
/* reset the phy */
|
|
miiphy_reset(name, devadr);
|
|
|
|
printf(PHY_NO" Initialized on %s\n", name);
|
|
}
|
|
|
|
void reset_phy(void)
|
|
{
|
|
mv_phy_init("egiga0");
|
|
|
|
#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
|
|
/* Kirkwood ethernet driver is written with the assumption that in case
|
|
* of multiple PHYs, their addresses are consecutive. But unfortunately
|
|
* in case of OpenRD-Client, PHY addresses are not consecutive.*/
|
|
miiphy_write("egiga1", 0xEE, 0xEE, 24);
|
|
#endif
|
|
|
|
#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \
|
|
defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
|
|
/* configure and initialize both PHY's */
|
|
mv_phy_init("egiga1");
|
|
#endif
|
|
}
|
|
#endif /* CONFIG_RESET_PHY_R */
|