mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-13 16:37:30 +00:00
a5f8ccaeab
- corvus board fix problems with toshiba nand chips on the corvus board problems with toshiba chips Manufacturer ID: 0x98 Chip ID: 0xdc encounterd. Solve this in the following way: - set other nand timings - enable CONFIG_SYS_NAND_READY_PIN - correct the MACH_TYPE setting Signed-off-by: Heiko Schocher <hs@denx.de>
282 lines
6.8 KiB
C
282 lines
6.8 KiB
C
/*
|
|
* Board functions for Siemens CORVUS (AT91SAM9G45) based board
|
|
* (C) Copyright 2013 Siemens AG
|
|
*
|
|
* Based on:
|
|
* U-Boot file: board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
|
|
* (C) Copyright 2007-2008
|
|
* Stelian Pop <stelian@popies.net>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/at91sam9g45_matrix.h>
|
|
#include <asm/arch/at91sam9_smc.h>
|
|
#include <asm/arch/at91_common.h>
|
|
#include <asm/arch/at91_pmc.h>
|
|
#include <asm/arch/at91_rstc.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/clk.h>
|
|
#include <lcd.h>
|
|
#include <atmel_lcdc.h>
|
|
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
|
|
#include <net.h>
|
|
#endif
|
|
#include <netdev.h>
|
|
#include <spi.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
static void corvus_nand_hw_init(void)
|
|
{
|
|
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
|
|
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
|
|
unsigned long csa;
|
|
|
|
/* Enable CS3 */
|
|
csa = readl(&matrix->ebicsa);
|
|
csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
|
|
writel(csa, &matrix->ebicsa);
|
|
|
|
/* Configure SMC CS3 for NAND/SmartMedia */
|
|
writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
|
|
AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
|
|
&smc->cs[3].setup);
|
|
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
|
|
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
|
|
&smc->cs[3].pulse);
|
|
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
|
|
&smc->cs[3].cycle);
|
|
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
|
|
AT91_SMC_MODE_EXNW_DISABLE |
|
|
#ifdef CONFIG_SYS_NAND_DBW_16
|
|
AT91_SMC_MODE_DBW_16 |
|
|
#else /* CONFIG_SYS_NAND_DBW_8 */
|
|
AT91_SMC_MODE_DBW_8 |
|
|
#endif
|
|
AT91_SMC_MODE_TDF_CYCLE(3),
|
|
&smc->cs[3].mode);
|
|
|
|
at91_periph_clk_enable(ATMEL_ID_PIOC);
|
|
at91_periph_clk_enable(ATMEL_ID_PIOA);
|
|
|
|
/* Enable NandFlash */
|
|
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
|
|
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
|
|
}
|
|
|
|
#if defined(CONFIG_SPL_BUILD)
|
|
#include <spl.h>
|
|
#include <nand.h>
|
|
|
|
void at91_spl_board_init(void)
|
|
{
|
|
/*
|
|
* For on the sam9m10g45ek board, the chip wm9711 stay in the test
|
|
* mode, so it need do some action to exit mode.
|
|
*/
|
|
at91_set_gpio_output(AT91_PIN_PD7, 0);
|
|
at91_set_gpio_output(AT91_PIN_PD8, 0);
|
|
at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
|
|
at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 12, 1);
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 13, 1);
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 15, 1);
|
|
|
|
corvus_nand_hw_init();
|
|
|
|
/* Configure recovery button PINs */
|
|
at91_set_gpio_input(AT91_PIN_PB7, 1);
|
|
|
|
/* check if button is pressed */
|
|
if (at91_get_gpio_value(AT91_PIN_PB7) == 0) {
|
|
u32 boot_device;
|
|
|
|
debug("Recovery button pressed\n");
|
|
boot_device = spl_boot_device();
|
|
switch (boot_device) {
|
|
#ifdef CONFIG_SPL_NAND_SUPPORT
|
|
case BOOT_DEVICE_NAND:
|
|
nand_init();
|
|
spl_nand_erase_one(0, 0);
|
|
break;
|
|
#endif
|
|
}
|
|
}
|
|
}
|
|
|
|
#include <asm/arch/atmel_mpddrc.h>
|
|
static void ddr2_conf(struct atmel_mpddr *ddr2)
|
|
{
|
|
ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
|
|
|
|
ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
|
|
ATMEL_MPDDRC_CR_NR_ROW_14 |
|
|
ATMEL_MPDDRC_CR_DIC_DS |
|
|
ATMEL_MPDDRC_CR_DQMS_SHARED |
|
|
ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
|
|
ddr2->rtr = 0x24b;
|
|
|
|
ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
|
|
2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
|
|
2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
|
|
8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 75 ns */
|
|
2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
|
|
1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
|
|
1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
|
|
2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
|
|
|
|
ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
|
|
200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
|
|
16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
|
|
14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
|
|
|
|
ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
|
|
0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
|
|
7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
|
|
2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
|
|
}
|
|
|
|
void mem_init(void)
|
|
{
|
|
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
|
|
struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
|
|
struct atmel_mpddr ddr2;
|
|
unsigned long csa;
|
|
|
|
ddr2_conf(&ddr2);
|
|
|
|
/* enable DDR2 clock */
|
|
writel(0x4, &pmc->scer);
|
|
|
|
/* Chip select 1 is for DDR2/SDRAM */
|
|
csa = readl(&mat->ebicsa);
|
|
csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
|
|
csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
|
|
writel(csa, &mat->ebicsa);
|
|
|
|
/* DDRAM2 Controller initialize */
|
|
ddr2_init(ATMEL_BASE_CS6, &ddr2);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_CMD_USB
|
|
static void taurus_usb_hw_init(void)
|
|
{
|
|
at91_periph_clk_enable(ATMEL_ID_PIODE);
|
|
|
|
at91_set_gpio_output(AT91_PIN_PD1, 0);
|
|
at91_set_gpio_output(AT91_PIN_PD3, 0);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_MACB
|
|
static void corvus_macb_hw_init(void)
|
|
{
|
|
/* Enable clock */
|
|
at91_periph_clk_enable(ATMEL_ID_EMAC);
|
|
|
|
/*
|
|
* Disable pull-up on:
|
|
* RXDV (PA15) => PHY normal mode (not Test mode)
|
|
* ERX0 (PA12) => PHY ADDR0
|
|
* ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
|
|
*
|
|
* PHY has internal pull-down
|
|
*/
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 15, 0);
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 12, 0);
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 13, 0);
|
|
|
|
at91_phy_reset();
|
|
|
|
/* Re-enable pull-up */
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 15, 1);
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 12, 1);
|
|
at91_set_pio_pullup(AT91_PIO_PORTA, 13, 1);
|
|
|
|
/* And the pins. */
|
|
at91_macb_hw_init();
|
|
}
|
|
#endif
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
at91_seriald_hw_init();
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
|
|
|
|
#ifdef CONFIG_CMD_NAND
|
|
corvus_nand_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_ATMEL_SPI
|
|
at91_spi0_hw_init(1 << 4);
|
|
#endif
|
|
#ifdef CONFIG_HAS_DATAFLASH
|
|
at91_spi0_hw_init(1 << 0);
|
|
#endif
|
|
#ifdef CONFIG_MACB
|
|
corvus_macb_hw_init();
|
|
#endif
|
|
#ifdef CONFIG_CMD_USB
|
|
taurus_usb_hw_init();
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
|
|
CONFIG_SYS_SDRAM_SIZE);
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
int rc = 0;
|
|
#ifdef CONFIG_MACB
|
|
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
|
|
#endif
|
|
return rc;
|
|
}
|
|
|
|
/* SPI chip select control */
|
|
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
|
|
{
|
|
return bus == 0 && cs < 2;
|
|
}
|
|
|
|
void spi_cs_activate(struct spi_slave *slave)
|
|
{
|
|
switch (slave->cs) {
|
|
case 1:
|
|
at91_set_gpio_output(AT91_PIN_PB18, 0);
|
|
break;
|
|
case 0:
|
|
default:
|
|
at91_set_gpio_output(AT91_PIN_PB3, 0);
|
|
break;
|
|
}
|
|
}
|
|
|
|
void spi_cs_deactivate(struct spi_slave *slave)
|
|
{
|
|
switch (slave->cs) {
|
|
case 1:
|
|
at91_set_gpio_output(AT91_PIN_PB18, 1);
|
|
break;
|
|
case 0:
|
|
default:
|
|
at91_set_gpio_output(AT91_PIN_PB3, 1);
|
|
break;
|
|
}
|
|
}
|