u-boot/board/freescale/imx8mq_evk
Peng Fan 86ac7a9a5d imx: add i.MX8MQ EVK support
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy
firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to
DRAM.

The boot log with Arm trusted firmware console enabled:
"
U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
PMIC:  PFUZE100 ID=0x10
Normal Boot
Trying to boot from MMC2
NOTICE:  Configureing TZASC380
NOTICE:  BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty
NOTICE:  BL31: Built : 09:28:54, Nov  8 2018
lpddr4 swffc start
NOTICE:  sip svc init

U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)

CPU:   Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: Freescale i.MX8MQ EVK
DRAM:  3 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:
Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Hit any key to stop autoboot:  0
"

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-01-01 14:12:18 +01:00
..
imx8mq_evk.c imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00
Kconfig imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00
lpddr4_timing.c imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00
lpddr4_timing_b0.c imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00
MAINTAINERS imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00
Makefile imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00
README imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00
spl.c imx: add i.MX8MQ EVK support 2019-01-01 14:12:18 +01:00

U-Boot for the NXP i.MX8MQ EVK board

Quick Start
====================
- Build the ARM Trusted firmware binary
- Get ddr and hdmi fimware
- Build U-Boot
- Boot

Get and Build the ARM Trusted firmware
====================
Get ATF from: https://source.codeaurora.org/external/imx/imx-atf
branch: imx_4.14.62_1.0.0_beta
$ make PLAT=imx8mq bl31

Get the ddr and hdmi firmware
====================
Note: srctree is U-Boot source directory
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-7.9.bin
$ chmod +x firmware-imx-7.9.bin
$ cp firmware-imx-7.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(srctree)
$ cp firmware-imx-7.9/firmware-imx-7.9/firmware/ddr/synopsys/lpddr4*.bin $(srctee)

Build U-Boot
====================
$ export ARCH=arm64
$ export CROSS_COMPILE=aarch64-poky-linux-
$ make imx8mq_evk_defconfig
$ make flash.bin

Burn the flash.bin to MicroSD card offset 33KB
$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33

Boot
====================
Set Boot switch SW801: 1100 and Bmode: 10 to boot from Micro SD.