u-boot/include/configs/mx31pdk.h
Wolfgang Denk 87a5d60103 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
2011-10-28 00:15:19 +02:00

234 lines
7 KiB
C

/*
* (C) Copyright 2008 Magnus Lilja <lilja.magnus@gmail.com>
*
* (C) Copyright 2004
* Texas Instruments.
* Richard Woodruff <r-woodruff2@ti.com>
* Kshitij Gupta <kshitij@ti.com>
*
* Configuration settings for the Freescale i.MX31 PDK board.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
#define CONFIG_ARM1136 /* This is an arm1136 CPU core */
#define CONFIG_MX31 /* in a mx31 */
#define CONFIG_MX31_HCLK_FREQ 26000000
#define CONFIG_MX31_CLK32 32768
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_MACH_TYPE MACH_TYPE_MX31_3DS
#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (2*CONFIG_ENV_SIZE + 2 * 128 * 1024)
/*
* Hardware drivers
*/
#define CONFIG_MXC_UART
#define CONFIG_SYS_MX31_UART1
#define CONFIG_HW_WATCHDOG
#define CONFIG_MXC_GPIO
#define CONFIG_HARD_SPI
#define CONFIG_MXC_SPI
#define CONFIG_DEFAULT_SPI_BUS 1
#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
/* PMIC Controller */
#define CONFIG_PMIC
#define CONFIG_PMIC_SPI
#define CONFIG_PMIC_FSL
#define CONFIG_FSL_PMIC_BUS 1
#define CONFIG_FSL_PMIC_CS 2
#define CONFIG_FSL_PMIC_CLK 1000000
#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
#define CONFIG_FSL_PMIC_BITLEN 32
#define CONFIG_RTC_MC13783
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/***********************************************************
* Command definition
***********************************************************/
#include <config_cmd_default.h>
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SPI
#define CONFIG_CMD_DATE
#define CONFIG_CMD_NAND
/*
* Disabled due to compilation errors in cmd_bootm.c (IMLS seems to require
* that CFG_NO_FLASH is undefined).
*/
#undef CONFIG_CMD_IMLS
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_BOOTDELAY 3
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
"bootargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs " \
"ip=dhcp nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \
"bootcmd=run bootcmd_net\0" \
"bootcmd_net=run bootargs_base bootargs_mtd bootargs_nfs; " \
"tftpboot 0x81000000 uImage-mx31; bootm\0" \
"prg_uboot=tftpboot 0x81000000 u-boot-nand.bin; " \
"nand erase 0x0 0x40000; " \
"nand write 0x81000000 0x0 0x40000\0"
#define CONFIG_SMC911X
#define CONFIG_SMC911X_BASE 0xB6000000
#define CONFIG_SMC911X_32_BIT
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "MX31PDK U-Boot > "
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT)+16)
/* max number of command args */
#define CONFIG_SYS_MAXARGS 16
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x10000
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x81000000
#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING
/*-----------------------------------------------------------------------
* Stack sizes
*
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE
#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_GBL_DATA_OFFSET)
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
/* No NOR flash present */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x40000
#define CONFIG_ENV_OFFSET_REDUND 0x60000
#define CONFIG_ENV_SIZE (128 * 1024)
/*
* NAND driver
*/
#define CONFIG_NAND_MXC
#define CONFIG_MXC_NAND_REGS_BASE NFC_BASE_ADDR
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR
#define CONFIG_MXC_NAND_HWECC
#define CONFIG_SYS_NAND_LARGEPAGE
/* NAND configuration for the NAND_SPL */
/* Start copying real U-boot from the second page */
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x800
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x30000
/* Load U-Boot to this address */
#define CONFIG_SYS_NAND_U_BOOT_DST 0x87f00000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_SIZE (256 * 1024 * 1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
/* Configuration of lowlevel_init.S (clocks and SDRAM) */
#define CCM_CCMR_SETUP 0x074B0BF5
#define CCM_PDR0_SETUP_532MHZ (PDR0_CSI_PODF(0x1ff) | PDR0_PER_PODF(7) | \
PDR0_HSP_PODF(3) | PDR0_NFC_PODF(5) | \
PDR0_IPG_PODF(1) | PDR0_MAX_PODF(3) | \
PDR0_MCU_PODF(0))
#define CCM_MPCTL_SETUP_532MHZ (PLL_PD(0) | PLL_MFD(51) | PLL_MFI(10) | \
PLL_MFN(12))
#define ESDMISC_MDDR_SETUP 0x00000004
#define ESDMISC_MDDR_RESET_DL 0x0000000c
#define ESDCFG0_MDDR_SETUP 0x006ac73a
#define ESDCTL_ROW_COL (ESDCTL_SDE | ESDCTL_ROW(2) | ESDCTL_COL(2))
#define ESDCTL_SETTINGS (ESDCTL_ROW_COL | ESDCTL_SREFR(3) | \
ESDCTL_DSIZ(2) | ESDCTL_BL(1))
#define ESDCTL_PRECHARGE (ESDCTL_ROW_COL | ESDCTL_CMD_PRECHARGE)
#define ESDCTL_AUTOREFRESH (ESDCTL_ROW_COL | ESDCTL_CMD_AUTOREFRESH)
#define ESDCTL_LOADMODEREG (ESDCTL_ROW_COL | ESDCTL_CMD_LOADMODEREG)
#define ESDCTL_RW ESDCTL_SETTINGS
#endif /* __CONFIG_H */